Hello, I have a connection issue between my wireless card and my router. Basically the first time it connects fine, then for some reason it disconnects and then it is quite hard to reconnect. With wicd, it would just not see any network anymore. I switched to network manager and thought the issue was solved but when I have this issue it keeps popping up asking me for the password to use to connect (I am using wep2 personal). rmmod ath9k modprobe ath9 fixes the issue in most case. Here is my setup: I have a wifi card with an atheros chip: 05:04.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) I am using the module in the kernel that gets loaded automatically: ath9k 77563 0 ath9k_common 4902 1 ath9k ath9k_hw 286570 2 ath9k,ath9k_common ath 8822 2 ath9k,ath9k_hw mac80211 189270 2 ath9k,ath9k_common cfg80211 144231 4 ath9k,ath9k_common,ath,mac80211 led_class 2363 1 ath9k Linux 2.6.35-ARCH #1 SMP PREEMPT Wed Sep 29 08:45:18 CEST 2010 x86_64 Intel(R) Core(TM) i5 CPU 750 @ 2.67GHz GenuineIntel GNU/Linux I see this in dmesg: TCP: Peer 121.223.98.212:18563/57886 unexpectedly shrunk window 2511361533:2511363096 (repaired) No probe response from AP *MACADDRESS* after 500ms, disconnecting. cfg80211: Calling CRDA to update world regulatory domain [drm:output_poll_execute] *ERROR* delayed enqueue failed -125 ath9k 0000:05:04.0: PCI INT A disabled ath9k: Driver unloaded ath9k 0000:05:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 ath: EEPROM regdomain: 0x809c ath: EEPROM indicates we should expect a country code ath: doing EEPROM country->regdmn map search ath: country maps to regdmn code: 0x52 ath: Country alpha2 being used: CN ath: Regpair used: 0x52 phy1: Selected rate control algorithm 'ath9k_rate_control' cfg80211: Calling CRDA for country: CN Registered led device: ath9k-phy1::radio Registered led device: ath9k-phy1::assoc Registered led device: ath9k-phy1::tx Registered led device: ath9k-phy1::rx phy1: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81 mem=0xffffc900040c0000, irq=16 wlan0: authenticate with *MACADDRESS* (try 1) wlan0: authenticated wlan0: associate with *MACADDRESS* (try 1) wlan0: RX AssocResp from *MACADDRESS* (capab=0x411 status=0 aid=1) wlan0: associated [drm:output_poll_execute] *ERROR* delayed enqueue failed -125 [drm:output_poll_execute] *ERROR* delayed enqueue failed -125 [drm:output_poll_execute] *ERROR* delayed enqueue failed -125 [drm:output_poll_execute] *ERROR* delayed enqueue failed -125 [drm:output_poll_execute] *ERROR* delayed enqueue failed -125 [drm:output_poll_execute] *ERROR* delayed enqueue failed -125 No probe response from AP *MACADDRESS* after 500ms, disconnecting. cfg80211: Calling CRDA to update world regulatory domain I am in the USA, not sure why it says the country code is CN. Since I did not get that issue with my previous linksys / broadcom card I am guessing the issue lies within ath9k but I could be wrong... This is NM version: 0.8.1-1 Not sure what else to report... Thank you! John -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html