On Fri, 2010-06-25 at 18:01 +0200, Denis 'GNUtoo' Carikli wrote: > [ 2132.599578] wl1251: cmd configure > [ 2132.619567] wl1251: acx wake up conditions > [ 2132.619628] wl1251: cmd configure > [ 2132.639587] wl1251: cmd set ps mode > [ 2132.640747] wl1251: sleep auth psm/elp > [ 2132.640808] wl1251: acx sleep auth > [ 2132.640808] wl1251: cmd configure > [ 2132.650268] wl1251: elp work > [ 2132.650299] wl1251: chip to elp > [ 2133.239471] wl1251: IRQ > [ 2133.239654] wl1251: IRQ work > [ 2133.239654] wl1251: waking up chip from elp > [ 2133.239715] wl1251: wakeup time: 0 ms does it mean that here it works? > [ 2133.239868] wl1251: intr: 0x3 > [ 2133.239929] wl1251: RX: FW +1 > [ 2133.239929] wl1251: RX counter: 7 > [ 2133.239959] wl1251: WL1251_ACX_INTR_RX0_DATA > [ 2133.240081] wl1251: rx skb 0xc61c3480: 88 B > [ 2133.240203] wl1251: WL1251_ACX_INTR_TX_RESULT > [ 2133.240478] wl1251: tx status id 0 skb 0xc635f480 failures 0 rate > 0x1 > status 0x0 () > [ 2133.251251] wl1251: elp work > [ 2133.264434] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2133.479278] wlan0: no IPv6 routers present > [ 2134.269470] mmc0: Command CRC error > [ 2134.269561] mmc0:0001: error -84 reading SDIO_CCCR_INTx > [ 2135.284484] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2136.289428] mmc0: Command CRC error > [ 2136.289489] mmc0:0001: error -84 reading SDIO_CCCR_INTx > [ 2137.304504] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2138.309478] mmc0: Command CRC error > [ 2138.309539] mmc0:0001: error -84 reading SDIO_CCCR_INTx > [ 2139.324523] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2140.329437] mmc0: Command CRC error > [ 2140.329498] mmc0:0001: error -84 reading SDIO_CCCR_INTx > [ 2141.344512] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2142.349456] mmc0: Command CRC error > [ 2142.349548] mmc0:0001: error -84 reading SDIO_CCCR_INTx > [ 2143.364501] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2144.369476] mmc0: Command CRC error > [ 2144.369537] mmc0:0001: error -84 reading SDIO_CCCR_INTx > [ 2145.384490] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2146.389404] mmc0: Command CRC error > [ 2146.389495] mmc0:0001: error -84 reading SDIO_CCCR_INTx > [ 2147.404541] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2148.409454] mmc0: Command CRC error > [ 2148.409545] mmc0:0001: error -84 reading SDIO_CCCR_INTx > [ 2149.424530] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2150.429534] mmc0: Command CRC error > [ 2150.429595] mmc0:0001: error -84 reading SDIO_CCCR_INTx > [ 2151.444488] mmc0:0001: error -110 reading SDIO_CCCR_INTx > [ 2152.449432] mmc0: Command CRC error > [ 2152.449523] mmc0:0001: error -84 reading SDIO_CCCR_INTx and that here it doesn't anymore? > [ 2152.969360] wl1251: mac80211 config ch 7 psm off power 20 > [ 2152.969421] wl1251: waking up chip from elp > [ 2152.989410] wl1251: wakeup time: 20 ms > [ 2152.989440] wl1251: psm disabled > [ 2152.989471] wl1251: leaving psm > [ 2152.989471] wl1251: sleep auth cam Denis. -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
