On Sat, Mar 13, 2010 at 5:33 PM, Thijs van der Kraan <thijsvanderkraan@xxxxxxxxxx> wrote: > The zd1211rw does not work with the Shuttle PN15G (D-Link Corp. WL54). > After the driver fails it also break the device for my windows XP > install. > To get it back in working order I have to physically re-plug it while > windows is running, this is pretty annoying as the PN15G is meant to be, > and is, built inside my shuttle box. > > I tried another device that uses the same driver, the ZyAIR G-220, and > it works like a charm. > > - Is there a way to get the Shuttle PN15G working ? > - Can prevent the driver from breaking my device, so it will remain > working under windows XP. > > > Thijs van de Kraan > > > lsusb: > --------------- > Bus 001 Device 004: ID 0586:3401 ZyXEL Communications Corp. ZyAIR G-220 > Bus 001 Device 003: ID 07b8:6001 D-Link Corp. WL54 > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 004 Device 002: ID 04fc:05d8 Sunplus Technology Co., Ltd > Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > --------------- > > dmesg (Shuttle PN15G): > --------------- > [ 9.419022] zd1211rw 1-8:1.0: phy0 > [ 9.419050] usbcore: registered new interface driver zd1211rw > [ 11.618783] usb 1-8: firmware: requesting zd1211/zd1211b_ub > [ 11.979913] usb 1-8: firmware version 0x4810 and device bootcode > version 0x4721 differ > [ 11.979919] usb 1-8: firmware: requesting zd1211/zd1211b_ur > [ 12.184918] usb 1-8: firmware: requesting zd1211/zd1211b_uphr > [ 12.261522] zd1211rw 1-8:1.0: RF2959 is currently not supported for > ZD1211B devices Are you sure this is a ZD1211B, not a regular ZD1211? Try changing the USB ID definitions to mark this as a ZD1211. > [ 12.263744] eth0: link down > [ 12.263950] ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 14.491044] usb 1-8: firmware: requesting zd1211/zd1211b_ub > [ 14.496834] usb 1-8: firmware version 0x4810 and device bootcode > version 0x4721 differ > [ 14.496841] usb 1-8: firmware: requesting zd1211/zd1211b_ur > [ 15.526035] usb 1-8: USB control request for firmware upload failed. > Error number -110 > [ 15.526049] zd1211rw 1-8:1.0: couldn't load firmware. Error number > -110 > > dmesg (ZyAIR G-220): > --------------- > > [ 283.920025] usb 1-4: new high speed USB device using ehci_hcd and > address 4 > [ 284.070953] usb 1-4: configuration #1 chosen from 1 choice > [ 284.200081] usb 1-4: reset high speed USB device using ehci_hcd and > address 4 > [ 284.351553] phy1: Selected rate control algorithm 'minstrel' > [ 284.352966] zd1211rw 1-4:1.0: phy1 > [ 284.387607] usb 1-4: firmware: requesting zd1211/zd1211_ub > [ 284.422786] usb 1-4: firmware version 0x4330 and device bootcode > version 0x4810 differ > [ 284.422796] usb 1-4: firmware: requesting zd1211/zd1211_ur > [ 284.446550] usb 1-4: firmware: requesting zd1211/zd1211_uphr > [ 284.528039] zd1211rw 1-4:1.0: firmware version 4605 > [ 284.568044] zd1211rw 1-4:1.0: zd1211 chip 0586:3401 v4810 high > 00-13-49 AL2230_RF pa0 ----- > [ 284.570691] cfg80211: Calling CRDA for country: DE > [ 284.574176] cfg80211: Regulatory domain changed to country: DE > [ 284.574184] (start_freq - end_freq @ bandwidth), (max_antenna_gain, > max_eirp) > [ 284.574190] (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm) > [ 284.574195] (5150000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm) > [ 284.574200] (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm) > [ 284.589627] ADDRCONF(NETDEV_UP): wlan1: link is not ready > [ 291.145078] wlan1: authenticate with AP 00:21:29:8b:3a:49 > [ 291.146703] wlan1: authenticated > [ 291.146708] wlan1: associate with AP 00:21:29:8b:3a:49 > [ 291.148944] wlan1: RX AssocResp from 00:21:29:8b:3a:49 (capab=0x411 > status=0 aid=2) > [ 291.148950] wlan1: associated > [ 291.149928] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready > [ 301.720021] wlan1: no IPv6 routers present > > -- > To unsubscribe from this list: send the line "unsubscribe linux-wireless" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-) -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
