On 11/04/2009 07:00 PM, Tim Blechmann wrote: >> running the rt61pci module on 2.6.31.5 works fine, but using the recent >> linus/master (2.6.32-rc5) results in this: > > same issue with 2.6.32-rc5 ... new bootlog with more debugging info > attached ... i was still able to reproduce this issue with 2.6.32-rc8 ... it would be nice, if someone could have a look into this issue before 2.6.32 is released ... dmesg from 2.6.32-rc8: [ 10.249098] rt61pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 10.257182] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - NIC: 0xff80 [ 10.257184] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - Led: 0xe0ff [ 10.257187] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0302, rf: 0003, rev: 0002561c. [ 10.351794] Registered led device: rt61pci-phy0::radio [ 10.351839] Registered led device: rt61pci-phy0::assoc [ 14.342046] rt61pci 0000:06:00.0: firmware: requesting rt2561.bin [ 14.395533] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8. [ 14.421238] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102. [ 14.421245] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188. [ 14.421252] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0. [ 14.421258] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0. [ 273.404685] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2. [ 273.404687] Please file bug report to http://rt2x00.serialmonkey.com. [ 282.143549] wlan0: no IPv6 routers present [ 357.304908] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 2 [ 357.333806] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9 [ 360.172776] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2. [ 360.172778] Please file bug report to http://rt2x00.serialmonkey.com. [ 360.172782] phy0 -> rt2x00mac_tx_rts_cts: Warning - Failed to send RTS/CTS frame. [ 383.880010] No probe response from AP 00:24:fe:09:94:18 after 500ms, disconnecting. [ 383.880026] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47. [ 383.880034] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94. [ 383.880042] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0. [ 383.880050] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0. [ 385.220460] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1) [ 385.421337] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 2) [ 385.621304] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 3) [ 385.821264] wlan0: direct probe to AP 00:24:fe:09:94:18 timed out lspci -vvv: 06:00.0 Network controller: RaLink RT2561/RT61 rev B 802.11g Subsystem: D-Link System Inc Device 3c09 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fb6f8000 (32-bit, non-prefetchable) [size=32K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: rt61pci Kernel modules: rt61pci thanks, tim -- tim@xxxxxxxxxx http://tim.klingt.org Happiness is a byproduct of function, purpose, and conflict; those who seek happiness for itself seek victory without war. William S. Burroughs
Attachment:
signature.asc
Description: OpenPGP digital signature
