From: Senthil Balasubramanian <senthilkumar@xxxxxxxxxxx>
* Get power table offset from the EEPROM instead of using
a hardcoded value of -5 if the EEPROM rev is >= 21.
* Add support in the 4k eeprom code for tx power offset
in case we have a 4k AR9280 implementation.
* Fix tx power accuracy at high powers.
Signed-off-by: Senthil Balasubramanian <senthilkumar@xxxxxxxxxxx>
---
drivers/net/wireless/ath/ath9k/eeprom.h | 5 +-
drivers/net/wireless/ath/ath9k/eeprom_4k.c | 4 +-
drivers/net/wireless/ath/ath9k/eeprom_def.c | 102 +++++++++++++++++++++++++-
3 files changed, 104 insertions(+), 7 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/eeprom.h b/drivers/net/wireless/ath/ath9k/eeprom.h
index 3349274..2f2993b 100644
--- a/drivers/net/wireless/ath/ath9k/eeprom.h
+++ b/drivers/net/wireless/ath/ath9k/eeprom.h
@@ -134,6 +134,7 @@
#define AR5416_EEP_MINOR_VER_17 0x11
#define AR5416_EEP_MINOR_VER_19 0x13
#define AR5416_EEP_MINOR_VER_20 0x14
+#define AR5416_EEP_MINOR_VER_21 0x15
#define AR5416_EEP_MINOR_VER_22 0x16
#define AR5416_NUM_5G_CAL_PIERS 8
@@ -154,7 +155,7 @@
#define AR5416_BCHAN_UNUSED 0xFF
#define AR5416_MAX_PWR_RANGE_IN_HALF_DB 64
#define AR5416_MAX_CHAINS 3
-#define AR5416_PWR_TABLE_OFFSET -5
+#define AR5416_PWR_TABLE_OFFSET_DB -5
/* Rx gain type values */
#define AR5416_EEP_RXGAIN_23DB_BACKOFF 0
@@ -302,7 +303,7 @@ struct base_eep_header {
u8 txGainType;
u8 rcChainMask;
u8 desiredScaleCCK;
- u8 power_table_offset;
+ u8 pwr_table_offset;
u8 frac_n_5g;
u8 futureBase_3[21];
} __packed;
diff --git a/drivers/net/wireless/ath/ath9k/eeprom_4k.c b/drivers/net/wireless/ath/ath9k/eeprom_4k.c
index 2a27b1d..58167d8 100644
--- a/drivers/net/wireless/ath/ath9k/eeprom_4k.c
+++ b/drivers/net/wireless/ath/ath9k/eeprom_4k.c
@@ -210,6 +210,8 @@ static u32 ath9k_hw_4k_get_eeprom(struct ath_hw *ah,
return pBase->rxMask;
case EEP_FRAC_N_5G:
return 0;
+ case EEP_PWR_TABLE_OFFSET:
+ return AR5416_PWR_TABLE_OFFSET_DB;
default:
return 0;
}
@@ -753,7 +755,7 @@ static void ath9k_hw_4k_set_txpower(struct ath_hw *ah,
if (AR_SREV_9280_10_OR_LATER(ah)) {
for (i = 0; i < Ar5416RateSize; i++)
- ratesArray[i] -= AR5416_PWR_TABLE_OFFSET * 2;
+ ratesArray[i] -= AR5416_PWR_TABLE_OFFSET_DB * 2;
}
/* OFDM power per rate */
diff --git a/drivers/net/wireless/ath/ath9k/eeprom_def.c b/drivers/net/wireless/ath/ath9k/eeprom_def.c
index 8f04b64..404a034 100644
--- a/drivers/net/wireless/ath/ath9k/eeprom_def.c
+++ b/drivers/net/wireless/ath/ath9k/eeprom_def.c
@@ -291,6 +291,11 @@ static u32 ath9k_hw_def_get_eeprom(struct ath_hw *ah,
return pBase->frac_n_5g;
else
return 0;
+ case EEP_PWR_TABLE_OFFSET:
+ if (AR5416_VER_MASK >= AR5416_EEP_MINOR_VER_21)
+ return pBase->pwr_table_offset;
+ else
+ return AR5416_PWR_TABLE_OFFSET_DB;
default:
return 0;
}
@@ -741,6 +746,76 @@ static void ath9k_hw_get_def_gain_boundaries_pdadcs(struct ath_hw *ah,
return;
}
+static int16_t ath9k_change_gain_boundary_setting(struct ath_hw *ah,
+ u16 *gb,
+ u16 numXpdGain,
+ u16 pdGainOverlap_t2,
+ int8_t pwr_table_offset,
+ int16_t *diff)
+
+{
+ u16 k;
+
+ /* Prior to writing the boundaries or the pdadc vs. power table
+ * into the chip registers the default starting point on the pdadc
+ * vs. power table needs to be checked and the curve boundaries
+ * adjusted accordingly
+ */
+ if (AR_SREV_9280_20_OR_LATER(ah)) {
+ u16 gb_limit;
+
+ if (AR5416_PWR_TABLE_OFFSET_DB != pwr_table_offset) {
+ /* get the difference in dB */
+ *diff = (u16)(pwr_table_offset - AR5416_PWR_TABLE_OFFSET_DB);
+ /* get the number of half dB steps */
+ *diff *= 2;
+ /* change the original gain boundary settings
+ * by the number of half dB steps
+ */
+ for (k = 0; k < numXpdGain; k++)
+ gb[k] = (u16)(gb[k] - *diff);
+ }
+ /* Because of a hardware limitation, ensure the gain boundary
+ * is not larger than (63 - overlap)
+ */
+ gb_limit = (u16)(AR5416_MAX_RATE_POWER - pdGainOverlap_t2);
+
+ for (k = 0; k < numXpdGain; k++)
+ gb[k] = (u16)min(gb_limit, gb[k]);
+ }
+
+ return *diff;
+}
+
+static void ath9k_adjust_pdadc_values(struct ath_hw *ah,
+ int8_t pwr_table_offset,
+ int16_t diff,
+ u8 *pdadcValues)
+{
+#define NUM_PDADC(diff) (AR5416_NUM_PDADC_VALUES - diff)
+ u16 k;
+
+ /* If this is a board that has a pwrTableOffset that differs from
+ * the default AR5416_PWR_TABLE_OFFSET_DB then the start of the
+ * pdadc vs pwr table needs to be adjusted prior to writing to the
+ * chip.
+ */
+ if (AR_SREV_9280_20_OR_LATER(ah)) {
+ if (AR5416_PWR_TABLE_OFFSET_DB != pwr_table_offset) {
+ /* shift the table to start at the new offset */
+ for (k = 0; k < (u16)NUM_PDADC(diff); k++ ) {
+ pdadcValues[k] = pdadcValues[k + diff];
+ }
+
+ /* fill the back of the table */
+ for (k = (u16)NUM_PDADC(diff); k < NUM_PDADC(0); k++) {
+ pdadcValues[k] = pdadcValues[NUM_PDADC(diff)];
+ }
+ }
+ }
+#undef NUM_PDADC
+}
+
static void ath9k_hw_set_def_power_cal_table(struct ath_hw *ah,
struct ath9k_channel *chan,
int16_t *pTxPowerIndexOffset)
@@ -756,15 +831,18 @@ static void ath9k_hw_set_def_power_cal_table(struct ath_hw *ah,
static u8 pdadcValues[AR5416_NUM_PDADC_VALUES];
u16 gainBoundaries[AR5416_PD_GAINS_IN_MASK];
u16 numPiers, i, j;
- int16_t tMinCalPower;
+ int16_t tMinCalPower, diff = 0;
u16 numXpdGain, xpdMask;
u16 xpdGainValues[AR5416_NUM_PD_GAINS] = { 0, 0, 0, 0 };
u32 reg32, regOffset, regChainOffset;
int16_t modalIdx;
+ int8_t pwr_table_offset;
modalIdx = IS_CHAN_2GHZ(chan) ? 1 : 0;
xpdMask = pEepData->modalHeader[modalIdx].xpdGain;
+ pwr_table_offset = ah->eep_ops->get_eeprom(ah, EEP_PWR_TABLE_OFFSET);
+
if ((pEepData->baseEepHeader.version & AR5416_EEP_VER_MINOR_MASK) >=
AR5416_EEP_MINOR_VER_2) {
pdGainOverlap_t2 =
@@ -844,6 +922,13 @@ static void ath9k_hw_set_def_power_cal_table(struct ath_hw *ah,
numXpdGain);
}
+ diff = ath9k_change_gain_boundary_setting(ah,
+ gainBoundaries,
+ numXpdGain,
+ pdGainOverlap_t2,
+ pwr_table_offset,
+ &diff);
+
if ((i == 0) || AR_SREV_5416_20_OR_LATER(ah)) {
if (OLC_FOR_AR9280_20_LATER) {
REG_WRITE(ah,
@@ -864,6 +949,10 @@ static void ath9k_hw_set_def_power_cal_table(struct ath_hw *ah,
}
}
+
+ ath9k_adjust_pdadc_values(ah, pwr_table_offset,
+ diff, pdadcValues);
+
regOffset = AR_PHY_BASE + (672 << 2) + regChainOffset;
for (j = 0; j < 32; j++) {
reg32 = ((pdadcValues[4 * j + 0] & 0xFF) << 0) |
@@ -1199,8 +1288,13 @@ static void ath9k_hw_def_set_txpower(struct ath_hw *ah,
}
if (AR_SREV_9280_10_OR_LATER(ah)) {
- for (i = 0; i < Ar5416RateSize; i++)
- ratesArray[i] -= AR5416_PWR_TABLE_OFFSET * 2;
+ for (i = 0; i < Ar5416RateSize; i++) {
+ int8_t pwr_table_offset;
+
+ pwr_table_offset = ah->eep_ops->get_eeprom(ah,
+ EEP_PWR_TABLE_OFFSET);
+ ratesArray[i] -= pwr_table_offset * 2;
+ }
}
REG_WRITE(ah, AR_PHY_POWER_TX_RATE1,
@@ -1299,7 +1393,7 @@ static void ath9k_hw_def_set_txpower(struct ath_hw *ah,
if (AR_SREV_9280_10_OR_LATER(ah))
regulatory->max_power_level =
- ratesArray[i] + AR5416_PWR_TABLE_OFFSET * 2;
+ ratesArray[i] + AR5416_PWR_TABLE_OFFSET_DB * 2;
else
regulatory->max_power_level = ratesArray[i];
--
1.6.4.4
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
