apply the conformance test limits (CTL) stored in the eeprom upon
the values calculated for the tx power (ar->power_*).
This is based on the implementation in the vendor driver
(hal/hpmain.c, line 3700 ff.) with one difference:
If any ctl mode isn't found in the eeprom, we fall back to the "lower",
legacy modes (5GHT20,11A or 2GHT20,11G,11B). Otus only did 5GHT20->11A.
Currently CTL are applied for the FCC group only.
Signed-off-by: Joerg Albert <jal2@xxxxxx>
---
The above diff is due to my AVM Fritz! USB stick having no *HT* CTL groups
in the eeprom at all.
Furthermore I moved the "TODO: heavy clip ..." to an, IMHO, better place.
drivers/net/wireless/ath/ar9170/phy.c | 165 ++++++++++++++++++++++++++++++++-
1 files changed, 164 insertions(+), 1 deletions(-)
diff --git a/drivers/net/wireless/ath/ar9170/phy.c b/drivers/net/wireless/ath/ar9170/phy.c
index 108ebfe..b3e5cf3 100644
--- a/drivers/net/wireless/ath/ar9170/phy.c
+++ b/drivers/net/wireless/ath/ar9170/phy.c
@@ -556,7 +556,6 @@ int ar9170_init_phy(struct ar9170 *ar, enum ieee80211_band band)
if (err)
return err;
- /* TODO: (heavy clip) regulatory domain power level fine-tuning. */
err = ar9170_init_phy_from_eeprom(ar, is_2ghz, is_40mhz);
if (err)
return err;
@@ -1238,6 +1237,164 @@ static int ar9170_set_freq_cal_data(struct ar9170 *ar,
return ar9170_regwrite_result();
}
+static u8 ar9170_get_max_edge_power(struct ar9170 *ar,
+ struct ar9170_calctl_edges edges[],
+ u32 freq)
+{
+/* TODO: move somewhere else */
+#define AR5416_MAX_RATE_POWER 63
+
+ int i;
+ u8 rc = AR5416_MAX_RATE_POWER;
+ u8 f;
+ if (freq < 3000)
+ f = freq - 2300;
+ else
+ f = (freq - 4800) / 5;
+
+ for (i = 0; i < AR5416_NUM_BAND_EDGES; i++) {
+ if (edges[i].channel == 0xff)
+ break;
+ if (f == edges[i].channel) {
+ /* exact freq match */
+ rc = edges[i].power_flags & ~AR9170_CALCTL_EDGE_FLAGS;
+ break;
+ }
+ if (i > 0 && f < edges[i].channel) {
+ if (f > edges[i-1].channel &&
+ edges[i-1].power_flags & AR9170_CALCTL_EDGE_FLAGS) {
+ /* lower channel has the inband flag set */
+ rc = edges[i-1].power_flags &
+ ~AR9170_CALCTL_EDGE_FLAGS;
+ }
+ break;
+ }
+ }
+
+ if (i == AR5416_NUM_BAND_EDGES) {
+ if (f > edges[i-1].channel &&
+ edges[i-1].power_flags & AR9170_CALCTL_EDGE_FLAGS) {
+ /* lower channel has the inband flag set */
+ rc = edges[i-1].power_flags &
+ ~AR9170_CALCTL_EDGE_FLAGS;
+ }
+ }
+ return rc;
+}
+
+/* calculate the conformance test limits and apply them to ar->power*
+ * (derived from otus hal/hpmain.c, line 3706 ff.)
+ */
+static void ar9170_calc_ctl(struct ar9170 *ar, u32 freq, enum ar9170_bw bw)
+{
+ u8 ctl_grp; /* CTL group */
+ u8 ctl_idx; /* CTL index */
+ int i, j;
+ struct ctl_modes {
+ u8 ctl_mode;
+ u8 max_power;
+ u8 *pwr_cal_data;
+ int pwr_cal_len;
+ } *modes;
+
+ /* order is relevant in the mode_list_*: we fall back to the
+ * lower indices if any mode is missed in the EEPROM.
+ */
+ struct ctl_modes mode_list_2ghz[] = {
+ { CTL_11B, 0, ar->power_2G_cck, 4 },
+ { CTL_11G, 0, ar->power_2G_ofdm, 4 },
+ { CTL_2GHT20, 0, ar->power_2G_ht20, 8 },
+ { CTL_2GHT40, 0, ar->power_2G_ht40, 8 },
+ };
+ struct ctl_modes mode_list_5ghz[] = {
+ { CTL_11A, 0, ar->power_5G_leg, 4 },
+ { CTL_5GHT20, 0, ar->power_5G_ht20, 8 },
+ { CTL_5GHT40, 0, ar->power_5G_ht40, 8 },
+ };
+ int nr_modes;
+
+#define EDGES(c, n) (ar->eeprom.ctl_data[c].control_edges[n])
+
+ /* TODO: investigate the differences between OTUS'
+ * hpreg.c::zfHpGetRegulatoryDomain() and
+ * ath/regd.c::ath_regd_get_band_ctl() -
+ * e.g. for FCC3_WORLD the OTUS procedure
+ * always returns CTL_FCC, while the one in ath/ delivers
+ * CTL_ETSI for 2GHz and CTL_FCC for 5GHz.
+ */
+ ctl_grp = ath_regd_get_band_ctl(&ar->common.regulatory,
+ ar->hw->conf.channel->band);
+
+ /* ctl group not found - either invalid band (NO_CTL) or ww roaming */
+ if (ctl_grp == NO_CTL || ctl_grp == SD_NO_CTL)
+ ctl_grp = CTL_FCC;
+
+ if (ctl_grp != CTL_FCC)
+ /* skip CTL and heavy clip for CTL_MKK and CTL_ETSI */
+ return;
+
+ if (ar->hw->conf.channel->band == IEEE80211_BAND_2GHZ) {
+ modes = mode_list_2ghz;
+ nr_modes = ARRAY_SIZE(mode_list_2ghz);
+ } else {
+ modes = mode_list_5ghz;
+ nr_modes = ARRAY_SIZE(mode_list_5ghz);
+ }
+
+ for (i = 0; i < nr_modes; i++) {
+ u8 c = ctl_grp | modes[i].ctl_mode;
+ for (ctl_idx = 0; ctl_idx < AR5416_NUM_CTLS; ctl_idx++)
+ if (c == ar->eeprom.ctl_index[ctl_idx])
+ break;
+ if (ctl_idx < AR5416_NUM_CTLS) {
+ int f_off = 0;
+
+ /* adjust freq for 40MHz */
+ if (modes[i].ctl_mode == CTL_2GHT40 ||
+ modes[i].ctl_mode == CTL_5GHT40) {
+ if (bw == AR9170_BW_40_BELOW)
+ f_off = -10;
+ else
+ f_off = 10;
+ }
+
+ modes[i].max_power =
+ ar9170_get_max_edge_power(ar, EDGES(ctl_idx, 1),
+ freq+f_off);
+
+ /* TODO: check if the regulatory max. power is
+ * controlled by cfg80211 for DFS
+ * (hpmain applies it to max_power itself for DFS freq)
+ */
+
+ } else {
+ /* Workaround in otus driver, hpmain.c, line 3906:
+ * if no data for 5GHT20 are found, take the
+ * legacy 5G value.
+ * We extend this here to fallback from any other *HT or
+ * 11G, too.
+ */
+ int k = i;
+
+ modes[i].max_power = AR5416_MAX_RATE_POWER;
+ while (k-- > 0) {
+ if (modes[k].max_power !=
+ AR5416_MAX_RATE_POWER) {
+ modes[i].max_power = modes[k].max_power;
+ break;
+ }
+ }
+ }
+
+ /* apply max power to pwr_cal_data (ar->power_*) */
+ for (j = 0; j < modes[i].pwr_cal_len; j++) {
+ modes[i].pwr_cal_data[j] = min(modes[i].pwr_cal_data[j],
+ modes[i].max_power);
+ }
+ }
+#undef EDGES
+}
+
static int ar9170_set_power_cal(struct ar9170 *ar, u32 freq, enum ar9170_bw bw)
{
struct ar9170_calibration_target_power_legacy *ctpl;
@@ -1340,6 +1497,12 @@ static int ar9170_set_power_cal(struct ar9170 *ar, u32 freq, enum ar9170_bw bw)
ctph[idx + 1].power[n]);
}
+
+ /* calc. conformance test limits and apply to ar->power*[] */
+ ar9170_calc_ctl(ar, freq, bw);
+
+ /* TODO: (heavy clip) regulatory domain power level fine-tuning. */
+
/* set ACK/CTS TX power */
ar9170_regwrite_begin(ar);
--
1.6.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
