On Mon, 2009-08-17 at 18:04 -0700, Luis R. Rodriguez wrote: > Aug 17 17:45:06 tux kernel: [ 380.596120] usb 1-3: firmware: > requesting ar9170.fw it would help if you turned off linebreaks for messages just like for patches :) > Aug 17 17:45:50 tux kernel: [ 424.812910] ------------[ cut here ]------------ > Aug 17 17:45:50 tux kernel: [ 424.812928] WARNING: at > net/wireless/sme.c:610 __cfg80211_disconnected+0x1fb/0x260 > [cfg80211]() > Aug 17 17:45:50 tux kernel: [ 424.812931] Hardware name: 7660A14 > Aug 17 17:45:50 tux kernel: [ 424.812933] deauth failed: -67 what was before that? > It seems I can get the second warning triggered when I disconnect due > to no probe response from AP: > > > [ 1060.261105] No probe response from AP <AP-MAC-ADDRESS>after 500ms, > disconnecting. > [ 1060.264257] phy1: device now idle > [ 1060.268293] phy1: Removed STA <AP-MAC-ADDRESS> > [ 1060.290788] phy1: Destroyed STA <AP-MAC-ADDRESS> > [ 1060.290961] wlan6: deauthenticating by local choice (reason=3) > [ 1060.291025] ------------[ cut here ]------------ > [ 1060.291057] WARNING: at net/wireless/sme.c:610 > __cfg80211_disconnected+0x1fb/0x260 [cfg80211]() Hmm, I can't: # ip link set wlan0 down # that's the AP [ 311.040157] wlan1: detected beacon loss from AP - sending probe request [ 311.540219] No probe response from AP 02:00:00:00:00:00 after 500ms, try 1 [ 312.040147] No probe response from AP 02:00:00:00:00:00 after 500ms, try 2 [ 312.540138] No probe response from AP 02:00:00:00:00:00 after 500ms, try 3 [ 313.040170] No probe response from AP 02:00:00:00:00:00 after 500ms, try 4 [ 313.540203] No probe response from AP 02:00:00:00:00:00 after 500ms, disconnecting. [ 313.543275] phy1:mac80211_hwsim_conf_tx (queue=0 txop=47 cw_min=3 cw_max=7 aifs=2) [ 313.546169] phy1:mac80211_hwsim_conf_tx (queue=1 txop=94 cw_min=7 cw_max=15 aifs=2) [ 313.549090] phy1:mac80211_hwsim_conf_tx (queue=2 txop=0 cw_min=15 cw_max=1023 aifs=3) [ 313.579536] phy1:mac80211_hwsim_conf_tx (queue=3 txop=0 cw_min=15 cw_max=1023 aifs=7) [ 313.582070] phy1: device now idle [ 313.583148] phy1:mac80211_hwsim_config (freq=2432 idle=1 ps=0) [ 313.585026] phy1:mac80211_hwsim_bss_info_changed(changed=0x8f) [ 313.586871] phy1:mac80211_hwsim_bss_info_changed: BSSID changed: 00:00:00:00:00:00 [ 313.589350] phy1: ASSOC: assoc=0 aid=1 [ 313.590685] phy1: ERP_CTS_PROT: 0 [ 313.591840] phy1: ERP_PREAMBLE: 0 [ 313.592979] phy1: ERP_SLOT: 0 [ 313.594020] phy1: Removed STA 02:00:00:00:00:00 [ 313.630576] phy1: Destroyed STA 02:00:00:00:00:00 [ 313.790503] phy1: device no longer idle - scanning Ok, so this is hwsim, but shouldn't make a difference at this level. johannes
Attachment:
signature.asc
Description: This is a digitally signed message part