Gábor Stefanik wrote:
> Seeing that this is still not in wireless-testing - this patch should
> be applied, the previously mentioned regressions were false alerts
> (Larry tested without this patch and with v478 firmware, which worked;
> while Mark applied this patch and used v410 firmware, which didn't
> work - when Mark upgraded to v478 firmware, his card too came to
> life.) So, please apply.
>
Just tested again, and this patch also works with v410 firmware.
Still need to load the module 3 times to get a working interface though,
so firmware version does not make any difference at all.
1st with b43_lpphy_op_get_default_chan returning 7:
[ 73.571467] b43-phy1 debug: RC calib: Failed to switch to channel
7, error =
-5
[ 73.576016] b43-phy1 debug: Switch to init channel failed, error
=
-5.
[ 73.576543] b43-phy1 ERROR: PHY init: Channel switch to default
failed
2nd load with it returning 1
[ 202.595791] b43-phy2 debug: Switch to init channel failed, error
= -5.
[ 202.596322] b43-phy2 ERROR: PHY init: Channel switch to default
failed
3rd load with returning 7 again.
[ 238.500062] b43-phy3 debug: Chip initialized
After 3rd load I can get the interface up without errors and I am able
to associate, do WPA and dhcp
with an AP on channel 11. Still no channel 1 AP's found here.
Mark
> 2009/8/18 Gábor Stefanik <netrolller.3d@xxxxxxxxx>:
>
>> Larry has started re-checking all current routines against a new
>> version of the Broadcom MIPS driver. This patch implements the first
>> round of changes he documented on the specs wiki.
>>
>> Also remove a few FIXMEs regarding missing initial values for variables
>> with dynamic initial values where reading the values has been implemented.
>>
>> Signed-off-by: Gábor Stefanik <netrolller.3d@xxxxxxxxx>
>> ---
>> drivers/net/wireless/b43/phy_lp.c | 98
>> +++++++++++++++++++------------
>> drivers/net/wireless/b43/phy_lp.h | 18 +++---
>> drivers/net/wireless/b43/tables_lpphy.c | 12 ++++-
>> 3 files changed, 82 insertions(+), 46 deletions(-)
>>
>> diff --git a/drivers/net/wireless/b43/phy_lp.c
>> b/drivers/net/wireless/b43/phy_lp.c
>> index 242338f..6c69cdb 100644
>> --- a/drivers/net/wireless/b43/phy_lp.c
>> +++ b/drivers/net/wireless/b43/phy_lp.c
>> @@ -719,9 +719,39 @@ static void lpphy_set_bb_mult(struct b43_wldev *dev, u8
>> bb_mult)
>> b43_lptab_write(dev, B43_LPTAB16(0, 87), (u16)bb_mult << 8);
>> }
>>
>> -static void lpphy_disable_crs(struct b43_wldev *dev)
>> +static void lpphy_set_deaf(struct b43_wldev *dev, bool user)
>> {
>> + struct b43_phy_lp *lpphy = dev->phy.lp;
>> +
>> + if (user)
>> + lpphy->crs_usr_disable = 1;
>> + else
>> + lpphy->crs_sys_disable = 1;
>> b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL, 0xFF1F, 0x80);
>> +}
>> +
>> +static void lpphy_clear_deaf(struct b43_wldev *dev, bool user)
>> +{
>> + struct b43_phy_lp *lpphy = dev->phy.lp;
>> +
>> + if (user)
>> + lpphy->crs_usr_disable = 0;
>> + else
>> + lpphy->crs_sys_disable = 0;
>> +
>> + if (!lpphy->crs_usr_disable && !lpphy->crs_sys_disable) {
>> + if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ)
>> + b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL,
>> + 0xFF1F, 0x60);
>> + else
>> + b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL,
>> + 0xFF1F, 0x20);
>> + }
>> +}
>> +
>> +static void lpphy_disable_crs(struct b43_wldev *dev, bool user)
>> +{
>> + lpphy_set_deaf(dev, user);
>> b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0xFFFC, 0x1);
>> b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x3);
>> b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0xFFFB);
>> @@ -749,12 +779,9 @@ static void lpphy_disable_crs(struct b43_wldev *dev)
>> b43_phy_write(dev, B43_LPPHY_RF_OVERRIDE_2, 0x3FF);
>> }
>>
>> -static void lpphy_restore_crs(struct b43_wldev *dev)
>> +static void lpphy_restore_crs(struct b43_wldev *dev, bool user)
>> {
>> - if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ)
>> - b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL, 0xFF1F, 0x60);
>> - else
>> - b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL, 0xFF1F, 0x20);
>> + lpphy_clear_deaf(dev, user);
>> b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFF80);
>> b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFC00);
>> }
>> @@ -800,10 +827,11 @@ static void lpphy_set_tx_gains(struct b43_wldev *dev,
>> b43_phy_maskset(dev, B43_LPPHY_TX_GAIN_CTL_OVERRIDE_VAL,
>> 0xF800, rf_gain);
>> } else {
>> - pa_gain = b43_phy_read(dev, B43_PHY_OFDM(0xFB)) & 0x7F00;
>> + pa_gain = b43_phy_read(dev, B43_PHY_OFDM(0xFB)) & 0x1FC0;
>> + pa_gain <<= 2;
>> b43_phy_write(dev, B43_LPPHY_TX_GAIN_CTL_OVERRIDE_VAL,
>> (gains.pga << 8) | gains.gm);
>> - b43_phy_maskset(dev, B43_LPPHY_TX_GAIN_CTL_OVERRIDE_VAL,
>> + b43_phy_maskset(dev, B43_PHY_OFDM(0xFB),
>> 0x8000, gains.pad | pa_gain);
>> b43_phy_write(dev, B43_PHY_OFDM(0xFC),
>> (gains.pga << 8) | gains.gm);
>> @@ -817,7 +845,7 @@ static void lpphy_set_tx_gains(struct b43_wldev *dev,
>> b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFF7F, 1 <<
>> 7);
>> b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_2, 0xBFFF, 1 <<
>> 14);
>> }
>> - b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFFBF, 1 << 6);
>> + b43_phy_maskset(dev, B43_LPPHY_AFE_CTL_OVR, 0xFFBF, 1 << 6);
>> }
>>
>> static void lpphy_rev0_1_set_rx_gain(struct b43_wldev *dev, u32 gain)
>> @@ -857,33 +885,33 @@ static void lpphy_rev2plus_set_rx_gain(struct
>> b43_wldev *dev, u32 gain)
>> }
>> }
>>
>> -static void lpphy_enable_rx_gain_override(struct b43_wldev *dev)
>> +static void lpphy_disable_rx_gain_override(struct b43_wldev *dev)
>> {
>> b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFFE);
>> b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFEF);
>> b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xFFBF);
>> if (dev->phy.rev >= 2) {
>> b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFEFF);
>> - if (b43_current_band(dev->wl) != IEEE80211_BAND_2GHZ)
>> - return;
>> - b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFBFF);
>> - b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFFF7);
>> + if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) {
>> + b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFBFF);
>> + b43_phy_mask(dev, B43_PHY_OFDM(0xE5), 0xFFF7);
>> + }
>> } else {
>> b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_2, 0xFDFF);
>> }
>> }
>>
>> -static void lpphy_disable_rx_gain_override(struct b43_wldev *dev)
>> +static void lpphy_enable_rx_gain_override(struct b43_wldev *dev)
>> {
>> b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x1);
>> b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x10);
>> b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_0, 0x40);
>> if (dev->phy.rev >= 2) {
>> b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x100);
>> - if (b43_current_band(dev->wl) != IEEE80211_BAND_2GHZ)
>> - return;
>> - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x400);
>> - b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x8);
>> + if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) {
>> + b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x400);
>> + b43_phy_set(dev, B43_PHY_OFDM(0xE5), 0x8);
>> + }
>> } else {
>> b43_phy_set(dev, B43_LPPHY_RF_OVERRIDE_2, 0x200);
>> }
>> @@ -1002,26 +1030,22 @@ static u32 lpphy_qdiv_roundup(u32 dividend, u32
>> divisor, u8 precision)
>> {
>> u32 quotient, remainder, rbit, roundup, tmp;
>>
>> - if (divisor == 0) {
>> - quotient = 0;
>> - remainder = 0;
>> - } else {
>> - quotient = dividend / divisor;
>> - remainder = dividend % divisor;
>> - }
>> + if (divisor == 0)
>> + return 0;
>> +
>> + quotient = dividend / divisor;
>> + remainder = dividend % divisor;
>>
>> rbit = divisor & 0x1;
>> roundup = (divisor >> 1) + rbit;
>> - precision--;
>>
>> - while (precision != 0xFF) {
>> + while (precision != 0) {
>> tmp = remainder - roundup;
>> quotient <<= 1;
>> - remainder <<= 1;
>> - if (remainder >= roundup) {
>> + if (remainder >= roundup)
>> remainder = (tmp << 1) + rbit;
>> - quotient--;
>> - }
>> + else
>> + remainder <<= 1;
>> precision--;
>> }
>>
>> @@ -1123,11 +1147,11 @@ static void lpphy_rev0_1_rc_calib(struct b43_wldev
>> *dev)
>> struct b43_phy_lp *lpphy = dev->phy.lp;
>> struct lpphy_iq_est iq_est;
>> struct lpphy_tx_gains tx_gains;
>> - static const u32 ideal_pwr_table[22] = {
>> + static const u32 ideal_pwr_table[21] = {
>> 0x10000, 0x10557, 0x10e2d, 0x113e0, 0x10f22, 0x0ff64,
>> 0x0eda2, 0x0e5d4, 0x0efd1, 0x0fbe8, 0x0b7b8, 0x04b35,
>> 0x01a5e, 0x00a0b, 0x00444, 0x001fd, 0x000ff, 0x00088,
>> - 0x0004c, 0x0002c, 0x0001a, 0xc0006,
>> + 0x0004c, 0x0002c, 0x0001a,
>> };
>> bool old_txg_ovr;
>> u8 old_bbmult;
>> @@ -1145,7 +1169,7 @@ static void lpphy_rev0_1_rc_calib(struct b43_wldev
>> *dev)
>> "RC calib: Failed to switch to channel 7, error = %d",
>> err);
>> }
>> - old_txg_ovr = (b43_phy_read(dev, B43_LPPHY_AFE_CTL_OVR) >> 6) & 1;
>> + old_txg_ovr = !!(b43_phy_read(dev, B43_LPPHY_AFE_CTL_OVR) & 0x40);
>> old_bbmult = lpphy_get_bb_mult(dev);
>> if (old_txg_ovr)
>> tx_gains = lpphy_get_tx_gains(dev);
>> @@ -1160,7 +1184,7 @@ static void lpphy_rev0_1_rc_calib(struct b43_wldev
>> *dev)
>> old_txpctl = lpphy->txpctl_mode;
>>
>> lpphy_set_tx_power_control(dev, B43_LPPHY_TXPCTL_OFF);
>> - lpphy_disable_crs(dev);
>> + lpphy_disable_crs(dev, true);
>> loopback = lpphy_loopback(dev);
>> if (loopback == -1)
>> goto finish;
>> @@ -1193,7 +1217,7 @@ static void lpphy_rev0_1_rc_calib(struct b43_wldev
>> *dev)
>> lpphy_stop_ddfs(dev);
>>
>> finish:
>> - lpphy_restore_crs(dev);
>> + lpphy_restore_crs(dev, true);
>> b43_phy_write(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, old_rf_ovrval);
>> b43_phy_write(dev, B43_LPPHY_RF_OVERRIDE_0, old_rf_ovr);
>> b43_phy_write(dev, B43_LPPHY_AFE_CTL_OVRVAL, old_afe_ovrval);
>> diff --git a/drivers/net/wireless/b43/phy_lp.h
>> b/drivers/net/wireless/b43/phy_lp.h
>> index 99cb038..e158d1f 100644
>> --- a/drivers/net/wireless/b43/phy_lp.h
>> +++ b/drivers/net/wireless/b43/phy_lp.h
>> @@ -825,11 +825,11 @@ struct b43_phy_lp {
>> enum b43_lpphy_txpctl_mode txpctl_mode;
>>
>> /* Transmit isolation medium band */
>> - u8 tx_isolation_med_band; /* FIXME initial value? */
>> + u8 tx_isolation_med_band;
>> /* Transmit isolation low band */
>> - u8 tx_isolation_low_band; /* FIXME initial value? */
>> + u8 tx_isolation_low_band;
>> /* Transmit isolation high band */
>> - u8 tx_isolation_hi_band; /* FIXME initial value? */
>> + u8 tx_isolation_hi_band;
>>
>> /* Max transmit power medium band */
>> u16 max_tx_pwr_med_band;
>> @@ -848,7 +848,7 @@ struct b43_phy_lp {
>> s16 txpa[3], txpal[3], txpah[3];
>>
>> /* Receive power offset */
>> - u8 rx_pwr_offset; /* FIXME initial value? */
>> + u8 rx_pwr_offset;
>>
>> /* TSSI transmit count */
>> u16 tssi_tx_count;
>> @@ -864,16 +864,16 @@ struct b43_phy_lp {
>> s8 tx_pwr_idx_over; /* FIXME initial value? */
>>
>> /* RSSI vf */
>> - u8 rssi_vf; /* FIXME initial value? */
>> + u8 rssi_vf;
>> /* RSSI vc */
>> - u8 rssi_vc; /* FIXME initial value? */
>> + u8 rssi_vc;
>> /* RSSI gs */
>> - u8 rssi_gs; /* FIXME initial value? */
>> + u8 rssi_gs;
>>
>> /* RC cap */
>> u8 rc_cap; /* FIXME initial value? */
>> /* BX arch */
>> - u8 bx_arch; /* FIXME initial value? */
>> + u8 bx_arch;
>>
>> /* Full calibration channel */
>> u8 full_calib_chan; /* FIXME initial value? */
>> @@ -885,6 +885,8 @@ struct b43_phy_lp {
>> /* Used for "Save/Restore Dig Filt State" */
>> u16 dig_flt_state[9];
>>
>> + bool crs_usr_disable, crs_sys_disable;
>> +
>> unsigned int pdiv;
>> };
>>
>> diff --git a/drivers/net/wireless/b43/tables_lpphy.c
>> b/drivers/net/wireless/b43/tables_lpphy.c
>> index 2721310..60d472f 100644
>> --- a/drivers/net/wireless/b43/tables_lpphy.c
>> +++ b/drivers/net/wireless/b43/tables_lpphy.c
>> @@ -2367,7 +2367,17 @@ static void lpphy_rev2plus_write_gain_table(struct
>> b43_wldev *dev, int offset,
>> tmp = data.pad << 16;
>> tmp |= data.pga << 8;
>> tmp |= data.gm;
>> - tmp |= 0x7f000000;
>> + if (dev->phy.rev >= 3) {
>> + if (b43_current_band(dev->wl) == IEEE80211_BAND_5GHZ)
>> + tmp |= 0x10 << 24;
>> + else
>> + tmp |= 0x70 << 24;
>> + } else {
>> + if (b43_current_band(dev->wl) == IEEE80211_BAND_5GHZ)
>> + tmp |= 0x14 << 24;
>> + else
>> + tmp |= 0x7F << 24;
>> + }
>> b43_lptab_write(dev, B43_LPTAB32(7, 0xC0 + offset), tmp);
>> tmp = data.bb_mult << 20;
>> tmp |= data.dac << 28;
>> --
>> 1.6.2.4
>>
>>
>>
>>
>>
>
>
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
