Some of the new variables in b43_phy_lp appear to be dead code in
the vendor driver; they will be removed if they remain unused when
LP-PHY implementation is finished.
Signed-off-by: Gábor Stefanik <netrolller.3d@xxxxxxxxx>
---
I've added a few FIXME comments, please review them.
Also please check that I used the correct types (e.g. u16) for the new variables.
Variable name mappings vs. the specification:
cckpo = tmp3
ofdmpo = tmp2
maxpwr = tmp1
The array txpwr_srom_max[3] has been broken up into 3 variables,
each called max_tx_pwr_{low|med|hi}_band. A struct holding 3 named u16s
may also be a good choice, but I am not fond of using an array for this.
drivers/net/wireless/b43/phy_lp.c | 83 ++++++++++++++++++++++++++++++++++++-
drivers/net/wireless/b43/phy_lp.h | 16 +++++++
2 files changed, 98 insertions(+), 1 deletions(-)
diff --git a/drivers/net/wireless/b43/phy_lp.c b/drivers/net/wireless/b43/phy_lp.c
index 43272a8..46fe476 100644
--- a/drivers/net/wireless/b43/phy_lp.c
+++ b/drivers/net/wireless/b43/phy_lp.c
@@ -59,6 +59,87 @@ static void b43_lpphy_op_free(struct b43_wldev *dev)
dev->phy.lp = NULL;
}
+static void lpphy_read_band_sprom(struct b43_wldev *dev)
+{
+ struct b43_phy_lp *lpphy = dev->phy.lp;
+ struct ssb_bus *bus = dev->dev->bus;
+ u16 cckpo, maxpwr;
+ u32 ofdmpo;
+ int i;
+
+ if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) {
+ lpphy->tx_isolation_med_band = bus->sprom.tri2g;
+ lpphy->bx_arch = bus->sprom.bxa2g;
+ lpphy->rssi_vf = bus->sprom.rssismf2g;
+ lpphy->rssi_vc = bus->sprom.rssismc2g;
+ lpphy->rssi_gs = bus->sprom.rssisav2g;
+ lpphy->txpa[0] = bus->sprom.pa0b0;
+ lpphy->txpa[1] = bus->sprom.pa0b1;
+ lpphy->txpa[2] = bus->sprom.pa0b2;
+ maxpwr = bus->sprom.maxpwr_bg;
+ lpphy->max_tx_pwr_med_band = maxpwr;
+ cckpo = bus->sprom.cck2gpo;
+ ofdmpo = bus->sprom.ofdm2gpo;
+ if (cckpo) {
+ for (i = 0; i < 4; i++) {
+ lpphy->tx_max_rate[i] =
+ maxpwr - (ofdmpo & 0xF) * 2;
+ ofdmpo << 4;
+ }
+ ofdmpo = bus->sprom.ofdm2gpo;
+ for (i = 4; i < 15; i++) {
+ lpphy->tx_max_rate[i] =
+ maxpwr - (ofdmpo & 0xF) * 2;
+ ofdmpo << 4;
+ }
+ } else {
+ ofdmpo &= 0xFF;
+ for (i = 0; i < 4; i++)
+ lpphy->tx_max_rate[i] = maxpwr;
+ for (i = 4; i < 15; i++)
+ lpphy->tx_max_rate[i] = maxpwr - ofdmpo;
+ }
+ } else { /* 5GHz */
+ lpphy->tx_isolation_low_band = bus->sprom.tri5gl;
+ lpphy->tx_isolation_med_band = bus->sprom.tri5g;
+ lpphy->tx_isolation_hi_band = bus->sprom.tri5gh;
+ lpphy->bx_arch = bus->sprom.bxa5g;
+ lpphy->rssi_vf = bus->sprom.rssismf5g;
+ lpphy->rssi_vc = bus->sprom.rssismc5g;
+ lpphy->rssi_gs = bus->sprom.rssisav5g;
+ lpphy->txpa[0] = bus->sprom.pa1b0;
+ lpphy->txpa[1] = bus->sprom.pa1b1;
+ lpphy->txpa[2] = bus->sprom.pa1b2;
+ lpphy->txpal[0] = bus->sprom.pa1lob0;
+ lpphy->txpal[1] = bus->sprom.pa1lob1;
+ lpphy->txpal[2] = bus->sprom.pa1lob2;
+ lpphy->txpah[0] = bus->sprom.pa1hib0;
+ lpphy->txpah[1] = bus->sprom.pa1hib1;
+ lpphy->txpah[2] = bus->sprom.pa1hib2;
+ maxpwr = bus->sprom.maxpwr_al;
+ ofdmpo = bus->sprom.ofdm5glpo;
+ lpphy->max_tx_pwr_low_band = maxpwr;
+ for (i = 4; i < 12; i++) {
+ lpphy->tx_max_ratel[i] = maxpwr - (ofdmpo & 0xF) * 2;
+ ofdmpo << 4;
+ }
+ maxpwr = bus->sprom.maxpwr_a;
+ ofdmpo = bus->sprom.ofdm5gpo;
+ lpphy->max_tx_pwr_med_band = maxpwr;
+ for (i = 4; i < 12; i++) {
+ lpphy->tx_max_rate[i] = maxpwr - (ofdmpo & 0xF) * 2;
+ ofdmpo << 4;
+ }
+ maxpwr = bus->sprom.maxpwr_ah;
+ ofdmpo = bus->sprom.ofdm5ghpo;
+ lpphy->max_tx_pwr_hi_band = maxpwr;
+ for (i = 4; i < 12; i++) {
+ lpphy->tx_max_rateh[i] = maxpwr - (ofdmpo & 0xF) * 2;
+ ofdmpo << 4;
+ }
+ }
+}
+
static void lpphy_adjust_gain_table(struct b43_wldev *dev)
{
struct b43_phy_lp *lpphy = dev->phy.lp;
@@ -694,7 +775,7 @@ static void lpphy_tx_pctl_init(struct b43_wldev *dev)
static int b43_lpphy_op_init(struct b43_wldev *dev)
{
- /* TODO: band SPROM */
+ lpphy_read_band_sprom(dev); //FIXME should this be in prepare_structs?
lpphy_baseband_init(dev);
lpphy_radio_init(dev);
//TODO calibrate RC
diff --git a/drivers/net/wireless/b43/phy_lp.h b/drivers/net/wireless/b43/phy_lp.h
index 13d89ea..9d0443c 100644
--- a/drivers/net/wireless/b43/phy_lp.h
+++ b/drivers/net/wireless/b43/phy_lp.h
@@ -831,6 +831,22 @@ struct b43_phy_lp {
/* Transmit isolation high band */
u8 tx_isolation_hi_band; /* FIXME initial value? */
+ /* Max transmit power medium band */
+ u16 max_tx_pwr_med_band;
+ /* Max transmit power low band */
+ u16 max_tx_pwr_low_band;
+ /* Max transmit power high band */
+ u16 max_tx_pwr_hi_band;
+
+ /* FIXME What are these used for? */
+ /* FIXME Is 15 the correct array size? */
+ u16 tx_sprom_max_rate[15];
+ u16 tx_sprom_max_ratel[15];
+ u16 tx_sprom_max_rateh[15];
+
+ /* Transmit power arrays */
+ s16 txpa[3], txpal[3], txpah[3];
+
/* Receive power offset */
u8 rx_pwr_offset; /* FIXME initial value? */
--
1.6.2.4
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
