Implement baseband init for rev.0 and rev.1 LP PHYs. Convert
boardflags_hi values to defines.
Implement b43_phy_copy for easier copying between registers, as needed
by LP-PHY init.
Signed-off-by: Gábor Stefanik<netrolller.3d@xxxxxxxxx>
Cc: Michael Buesch<mb@xxxxxxxxx>
Cc: Larry Finger<larry.finger@xxxxxxxxxxxx>
---
Hopefully this mail will survive the trip through the arcane world of Gmail's servers...
If this very-very-very-long line (including a few tab characters) doesn't get mangled, chances are that the mail didn't get mangled. More text to make this line even longer.
b43.h | 11 ++++++
phy_common.c | 7 ++++
phy_lp.c | 95 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
phy_lp.h | 8 +++-
phy_n.c | 3 +
5 files changed, 120 insertions(+), 4 deletions(-)
diff --git a/drivers/net/wireless/b43/b43.h b/drivers/net/wireless/b43/b43.h
index 4e8ad84..41ca727 100644
--- a/drivers/net/wireless/b43/b43.h
+++ b/drivers/net/wireless/b43/b43.h
@@ -142,6 +142,17 @@
#define B43_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */
#define B43_BFL_ALTIQ 0x8000 /* alternate I/Q settings */
+/* SPROM boardflags_hi values */
+#define B43_BFH_NOPA 0x0001 /* has no PA */
+#define B43_BFH_RSSIINV 0x0002 /* RSSI uses positive slope (not TSSI) */
+#define B43_BFH_PAREF 0x0004 /* uses the PARef LDO */
+#define B43_BFH_3TSWITCH 0x0008 /* uses a triple throw switch shared
+ * with bluetooth */
+#define B43_BFH_PHASESHIFT 0x0010 /* can support phase shifter */
+#define B43_BFH_BUCKBOOST 0x0020 /* has buck/booster */
+#define B43_BFH_FEM_BT 0x0040 /* has FEM and switch to share antenna
+ * with bluetooth */
+
/* GPIO register offset, in both ChipCommon and PCI core. */
#define B43_GPIO_CONTROL 0x6c
diff --git a/drivers/net/wireless/b43/phy_common.c b/drivers/net/wireless/b43/phy_common.c
index e176b6e..999e0bd 100644
--- a/drivers/net/wireless/b43/phy_common.c
+++ b/drivers/net/wireless/b43/phy_common.c
@@ -240,6 +240,13 @@ void b43_phy_write(struct b43_wldev *dev, u16 reg, u16 value)
dev->phy.ops->phy_write(dev, reg, value);
}
+void b43_phy_copy(struct b43_wldev *dev, u16 srcreg, u16 destreg)
+{
+ assert_mac_suspended(dev);
+ dev->phy.ops->phy_write(dev, destreg,
+ dev->phy.ops->phy_read(dev, srcreg));
+}
+
void b43_phy_mask(struct b43_wldev *dev, u16 offset, u16 mask)
{
b43_phy_write(dev, offset,
diff --git a/drivers/net/wireless/b43/phy_lp.c b/drivers/net/wireless/b43/phy_lp.c
index 58e319d..dbaa2e4 100644
--- a/drivers/net/wireless/b43/phy_lp.c
+++ b/drivers/net/wireless/b43/phy_lp.c
@@ -66,7 +66,100 @@ static void lpphy_table_init(struct b43_wldev *dev)
static void lpphy_baseband_rev0_1_init(struct b43_wldev *dev)
{
- B43_WARN_ON(1);//TODO rev< 2 not supported, yet.
+ struct ssb_bus *bus = dev->dev->bus;
+ struct b43_phy_lp *lpphy = dev->phy.lp;
+ u16 tmp, tmp2;
+
+ if (dev->phy.rev == 1&&
+ (bus->sprom.boardflags_hi& B43_BFH_FEM_BT)) {
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0x3F00, 0x0900);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xC0FF, 0x0B00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xC0FF, 0x0400);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xC0FF, 0x0B00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_5, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_5, 0xC0FF, 0x0900);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_6, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_6, 0xC0FF, 0x0B00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_7, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_7, 0xC0FF, 0x0900);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_8, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_8, 0xC0FF, 0x0B00);
+ } else if (b43_current_band(dev->wl) == IEEE80211_BAND_5GHZ ||
+ (bus->boardinfo.type == 0x048A) || ((dev->phy.rev == 0)&&
+ (bus->sprom.boardflags_lo& B43_BFL_FEM))) {
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xFFC0, 0x0001);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xC0FF, 0x0400);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xFFC0, 0x0001);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xC0FF, 0x0500);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xFFC0, 0x0002);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xC0FF, 0x0800);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xFFC0, 0x0002);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xC0FF, 0x0A00);
+ } else if (dev->phy.rev == 1 ||
+ (bus->sprom.boardflags_lo& B43_BFL_FEM)) {
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xFFC0, 0x0004);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xC0FF, 0x0800);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xFFC0, 0x0004);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xC0FF, 0x0C00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xFFC0, 0x0002);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xC0FF, 0x0100);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xFFC0, 0x0002);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xC0FF, 0x0300);
+ } else {
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xC0FF, 0x0900);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xC0FF, 0x0B00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xFFC0, 0x0006);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xC0FF, 0x0500);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xFFC0, 0x0006);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xC0FF, 0x0700);
+ }
+ if (dev->phy.rev == 1) {
+ b43_phy_copy(dev, B43_LPPHY_TR_LOOKUP_1, B43_LPPHY_TR_LOOKUP_5);
+ b43_phy_copy(dev, B43_LPPHY_TR_LOOKUP_2, B43_LPPHY_TR_LOOKUP_6);
+ b43_phy_copy(dev, B43_LPPHY_TR_LOOKUP_3, B43_LPPHY_TR_LOOKUP_7);
+ b43_phy_copy(dev, B43_LPPHY_TR_LOOKUP_4, B43_LPPHY_TR_LOOKUP_8);
+ }
+ if (bus->sprom.boardflags_hi& B43_BFH_FEM_BT)&&
+ (bus->chip_id == 0x5354)&&
+ (bus->chip_package == SSB_CHIPPACK_BCM4712S)) {
+ b43_phy_set(dev, B43_LPPHY_CRSGAIN_CTL, 0x0006);
+ b43_phy_write(dev, B43_LPPHY_GPIO_SELECT, 0x0005);
+ b43_phy_write(dev, B43_LPPHY_GPIO_OUTEN, 0xFFFF);
+ b43_hf_write(dev, b43_hf_read | 0x0800ULL<< 32);
+ }
+ if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) {
+ b43_phy_set(dev, B43_LPPHY_LP_PHY_CTL, 0x8000);
+ b43_phy_set(dev, B43_LPPHY_CRSGAIN_CTL, 0x0040);
+ b43_phy_maskset(dev, B43_LPPHY_MINPWR_LEVEL, 0x00FF, 0xA400);
+ b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL, 0xF0FF, 0x0B00);
+ b43_phy_maskset(dev, 0x030, 0xFFF8, 0x0007);
+ b43_phy_maskset(dev, B43_LPPHY_DSSS_CONFIRM_CNT, 0xFFF8, 0x0003);
+ b43_phy_maskset(dev, B43_LPPHY_DSSS_CONFIRM_CNT, 0xFFC7, 0x0020);
+ b43_phy_mask(dev, B43_LPPHY_IDLEAFTERPKTRXTO, 0x00FF);
+ } else { /* 5GHz */
+ b43_phy_mask(dev, 0x448, 0x7FFF);
+ b43_phy_mask(dev, B43_LPPHY_CRSGAIN_CTL, 0xFFBF);
+ }
+ if (dev->phy.rev == 1) {
+ tmp = b43_read(dev, B43_LPPHY_CLIPCTRTHRESH);
+ tmp2 = (tmp& 0x03E0)>> 5
+ tmp2 |= tmp<< 5;
+ b43_phy_write(dev, 0x4C3, tmp2);
+ tmp = b43_read(dev, B43_LPPHY_OFDMSYNCTHRESH0);
+ tmp2 = (tmp& 0x1F00)>> 8
+ tmp2 |= tmp<< 5;
+ b43_phy_write(dev, 0x4C4, tmp2);
+ tmp = b43_read(dev, B43_LPPHY_VERYLOWGAINDB);
+ tmp2 = tmp& 0x00FF
+ tmp2 |= tmp<< 8;
+ b43_phy_write(dev, 0x4C5, tmp2);
+ }
}
static void lpphy_baseband_rev2plus_init(struct b43_wldev *dev)
diff --git a/drivers/net/wireless/b43/phy_lp.h b/drivers/net/wireless/b43/phy_lp.h
index 18370b4..d0e67e4 100644
--- a/drivers/net/wireless/b43/phy_lp.h
+++ b/drivers/net/wireless/b43/phy_lp.h
@@ -273,12 +273,16 @@
#define B43_LPPHY_AFE_DDFS_POINTER_INIT B43_PHY_OFDM(0xB8) /* AFE DDFS pointer init */
#define B43_LPPHY_AFE_DDFS_INCR_INIT B43_PHY_OFDM(0xB9) /* AFE DDFS incr init */
#define B43_LPPHY_MRCNOISEREDUCTION B43_PHY_OFDM(0xBA) /* mrcNoiseReduction */
-#define B43_LPPHY_TRLOOKUP3 B43_PHY_OFDM(0xBB) /* TRLookup3 */
-#define B43_LPPHY_TRLOOKUP4 B43_PHY_OFDM(0xBC) /* TRLookup4 */
+#define B43_LPPHY_TR_LOOKUP_3 B43_PHY_OFDM(0xBB) /* TR Lookup 3 */
+#define B43_LPPHY_TR_LOOKUP_4 B43_PHY_OFDM(0xBC) /* TR Lookup 4 */
#define B43_LPPHY_RADAR_FIFO_STAT B43_PHY_OFDM(0xBD) /* Radar FIFO Status */
#define B43_LPPHY_GPIO_OUTEN B43_PHY_OFDM(0xBE) /* GPIO Out enable */
#define B43_LPPHY_GPIO_SELECT B43_PHY_OFDM(0xBF) /* GPIO Select */
#define B43_LPPHY_GPIO_OUT B43_PHY_OFDM(0xC0) /* GPIO Out */
+#define B43_LPPHY_TR_LOOKUP_5 B43_PHY_OFDM(0xC7) /* TR Lookup 5 */
+#define B43_LPPHY_TR_LOOKUP_6 B43_PHY_OFDM(0xC8) /* TR Lookup 6 */
+#define B43_LPPHY_TR_LOOKUP_7 B43_PHY_OFDM(0xC9) /* TR Lookup 7 */
+#define B43_LPPHY_TR_LOOKUP_8 B43_PHY_OFDM(0xCA) /* TR Lookup 8 */
diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c
index 8bcfda5..14ad95a 100644
--- a/drivers/net/wireless/b43/phy_n.c
+++ b/drivers/net/wireless/b43/phy_n.c
@@ -137,7 +137,8 @@ static void b43_radio_init2055_post(struct b43_wldev *dev)
b43_radio_mask(dev, B2055_MASTER1, 0xFFF3);
msleep(1);
- if ((sprom->revision != 4) || !(sprom->boardflags_hi& 0x0002)) {
+ if ((sprom->revision != 4) ||
+ !(sprom->boardflags_hi& B43_BFH_RSSIINV)) {
if ((binfo->vendor != PCI_VENDOR_ID_BROADCOM) ||
(binfo->type != 0x46D) ||
(binfo->rev< 0x41)) {
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
