The same partition setting code can be used for both SPI and SDIO
modes, if we remove the spi-specific commands and use the more
generic buffer write routines. Do that and move it to io.c
since it deals with register/memory address offsets.
Signed-off-by: Bob Copeland <me@xxxxxxxxxxxxxxx>
---
drivers/net/wireless/wl12xx/io.c | 95 ++++++++++++++++++++++++++++++
drivers/net/wireless/wl12xx/io.h | 15 +++++-
drivers/net/wireless/wl12xx/spi.c | 117 -------------------------------------
drivers/net/wireless/wl12xx/spi.h | 11 ----
4 files changed, 109 insertions(+), 129 deletions(-)
diff --git a/drivers/net/wireless/wl12xx/io.c b/drivers/net/wireless/wl12xx/io.c
index 611b644..b4178d8 100644
--- a/drivers/net/wireless/wl12xx/io.c
+++ b/drivers/net/wireless/wl12xx/io.c
@@ -84,3 +84,98 @@ void wl12xx_reg_write32(struct wl12xx *wl, int addr, u32 val)
{
wl12xx_write32(wl, wl12xx_translate_reg_addr(wl, addr), val);
}
+
+/* Set the partitions to access the chip addresses.
+ *
+ * There are two VIRTUAL partitions (the memory partition and the
+ * registers partition), which are mapped to two different areas of the
+ * PHYSICAL (hardware) memory. This function also makes other checks to
+ * ensure that the partitions are not overlapping. In the diagram below, the
+ * memory partition comes before the register partition, but the opposite is
+ * also supported.
+ *
+ * PHYSICAL address
+ * space
+ *
+ * | |
+ * ...+----+--> mem_start
+ * VIRTUAL address ... | |
+ * space ... | | [PART_0]
+ * ... | |
+ * 0x00000000 <--+----+... ...+----+--> mem_start + mem_size
+ * | | ... | |
+ * |MEM | ... | |
+ * | | ... | |
+ * part_size <--+----+... | | {unused area)
+ * | | ... | |
+ * |REG | ... | |
+ * part_size | | ... | |
+ * + <--+----+... ...+----+--> reg_start
+ * reg_size ... | |
+ * ... | | [PART_1]
+ * ... | |
+ * ...+----+--> reg_start + reg_size
+ * | |
+ *
+ */
+void wl12xx_set_partition(struct wl12xx *wl,
+ u32 mem_start, u32 mem_size,
+ u32 reg_start, u32 reg_size)
+{
+ struct wl12xx_partition partition[2];
+
+ wl12xx_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
+ mem_start, mem_size);
+ wl12xx_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
+ reg_start, reg_size);
+
+ /* Make sure that the two partitions together don't exceed the
+ * address range */
+ if ((mem_size + reg_size) > HW_ACCESS_MEMORY_MAX_RANGE) {
+ wl12xx_debug(DEBUG_SPI, "Total size exceeds maximum virtual"
+ " address range. Truncating partition[0].");
+ mem_size = HW_ACCESS_MEMORY_MAX_RANGE - reg_size;
+ wl12xx_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
+ mem_start, mem_size);
+ wl12xx_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
+ reg_start, reg_size);
+ }
+
+ if ((mem_start < reg_start) &&
+ ((mem_start + mem_size) > reg_start)) {
+ /* Guarantee that the memory partition doesn't overlap the
+ * registers partition */
+ wl12xx_debug(DEBUG_SPI, "End of partition[0] is "
+ "overlapping partition[1]. Adjusted.");
+ mem_size = reg_start - mem_start;
+ wl12xx_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
+ mem_start, mem_size);
+ wl12xx_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
+ reg_start, reg_size);
+ } else if ((reg_start < mem_start) &&
+ ((reg_start + reg_size) > mem_start)) {
+ /* Guarantee that the register partition doesn't overlap the
+ * memory partition */
+ wl12xx_debug(DEBUG_SPI, "End of partition[1] is"
+ " overlapping partition[0]. Adjusted.");
+ reg_size = mem_start - reg_start;
+ wl12xx_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
+ mem_start, mem_size);
+ wl12xx_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
+ reg_start, reg_size);
+ }
+
+ partition[0].start = mem_start;
+ partition[0].size = mem_size;
+ partition[1].start = reg_start;
+ partition[1].size = reg_size;
+
+ wl->physical_mem_addr = mem_start;
+ wl->physical_reg_addr = reg_start;
+
+ wl->virtual_mem_addr = 0;
+ wl->virtual_reg_addr = mem_size;
+
+ wl->if_ops->write(wl, HW_ACCESS_PART0_SIZE_ADDR, partition,
+ sizeof(partition));
+}
diff --git a/drivers/net/wireless/wl12xx/io.h b/drivers/net/wireless/wl12xx/io.h
index ecc18b6..b1ea67a 100644
--- a/drivers/net/wireless/wl12xx/io.h
+++ b/drivers/net/wireless/wl12xx/io.h
@@ -23,6 +23,17 @@
#include "wl12xx.h"
+#define HW_ACCESS_MEMORY_MAX_RANGE 0x1FFC0
+
+#define HW_ACCESS_PART0_SIZE_ADDR 0x1FFC0
+#define HW_ACCESS_PART0_START_ADDR 0x1FFC4
+#define HW_ACCESS_PART1_SIZE_ADDR 0x1FFC8
+#define HW_ACCESS_PART1_START_ADDR 0x1FFCC
+
+#define HW_ACCESS_REGISTER_SIZE 4
+
+#define HW_ACCESS_PRAM_MAX_RANGE 0x3c000
+
static inline u32 wl12xx_read32(struct wl12xx *wl, int addr)
{
u32 response;
@@ -45,5 +56,7 @@ void wl12xx_mem_write32(struct wl12xx *wl, int addr, u32 val);
/* Registers IO */
u32 wl12xx_reg_read32(struct wl12xx *wl, int addr);
void wl12xx_reg_write32(struct wl12xx *wl, int addr, u32 val);
-
+void wl12xx_set_partition(struct wl12xx *wl,
+ u32 part_start, u32 part_size,
+ u32 reg_start, u32 reg_size);
#endif
diff --git a/drivers/net/wireless/wl12xx/spi.c b/drivers/net/wireless/wl12xx/spi.c
index 085755d..658464e 100644
--- a/drivers/net/wireless/wl12xx/spi.c
+++ b/drivers/net/wireless/wl12xx/spi.c
@@ -117,123 +117,6 @@ static void wl12xx_spi_reset_wake(struct wl12xx *wl)
wl12xx_spi_init(wl);
}
-/* Set the SPI partitions to access the chip addresses
- *
- * There are two VIRTUAL (SPI) partitions (the memory partition and the
- * registers partition), which are mapped to two different areas of the
- * PHYSICAL (hardware) memory. This function also makes other checks to
- * ensure that the partitions are not overlapping. In the diagram below, the
- * memory partition comes before the register partition, but the opposite is
- * also supported.
- *
- * PHYSICAL address
- * space
- *
- * | |
- * ...+----+--> mem_start
- * VIRTUAL address ... | |
- * space ... | | [PART_0]
- * ... | |
- * 0x00000000 <--+----+... ...+----+--> mem_start + mem_size
- * | | ... | |
- * |MEM | ... | |
- * | | ... | |
- * part_size <--+----+... | | {unused area)
- * | | ... | |
- * |REG | ... | |
- * part_size | | ... | |
- * + <--+----+... ...+----+--> reg_start
- * reg_size ... | |
- * ... | | [PART_1]
- * ... | |
- * ...+----+--> reg_start + reg_size
- * | |
- *
- */
-void wl12xx_set_partition(struct wl12xx *wl,
- u32 mem_start, u32 mem_size,
- u32 reg_start, u32 reg_size)
-{
- u8 tx_buf[sizeof(u32) + 2 * sizeof(struct wl12xx_partition)];
- struct wl12xx_partition *partition;
- struct spi_transfer t;
- struct spi_message m;
- u32 *cmd;
- size_t len;
- int addr;
-
- spi_message_init(&m);
- memset(&t, 0, sizeof(t));
- memset(tx_buf, 0, sizeof(tx_buf));
-
- cmd = (u32 *) tx_buf;
- partition = (struct wl12xx_partition *) (tx_buf + sizeof(u32));
- addr = HW_ACCESS_PART0_SIZE_ADDR;
- len = 2 * sizeof(struct wl12xx_partition);
-
- *cmd |= WSPI_CMD_WRITE;
- *cmd |= (len << WSPI_CMD_BYTE_LENGTH_OFFSET) & WSPI_CMD_BYTE_LENGTH;
- *cmd |= addr & WSPI_CMD_BYTE_ADDR;
-
- wl12xx_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
- mem_start, mem_size);
- wl12xx_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
- reg_start, reg_size);
-
- /* Make sure that the two partitions together don't exceed the
- * address range */
- if ((mem_size + reg_size) > HW_ACCESS_MEMORY_MAX_RANGE) {
- wl12xx_debug(DEBUG_SPI, "Total size exceeds maximum virtual"
- " address range. Truncating partition[0].");
- mem_size = HW_ACCESS_MEMORY_MAX_RANGE - reg_size;
- wl12xx_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
- mem_start, mem_size);
- wl12xx_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
- reg_start, reg_size);
- }
-
- if ((mem_start < reg_start) &&
- ((mem_start + mem_size) > reg_start)) {
- /* Guarantee that the memory partition doesn't overlap the
- * registers partition */
- wl12xx_debug(DEBUG_SPI, "End of partition[0] is "
- "overlapping partition[1]. Adjusted.");
- mem_size = reg_start - mem_start;
- wl12xx_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
- mem_start, mem_size);
- wl12xx_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
- reg_start, reg_size);
- } else if ((reg_start < mem_start) &&
- ((reg_start + reg_size) > mem_start)) {
- /* Guarantee that the register partition doesn't overlap the
- * memory partition */
- wl12xx_debug(DEBUG_SPI, "End of partition[1] is"
- " overlapping partition[0]. Adjusted.");
- reg_size = mem_start - reg_start;
- wl12xx_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
- mem_start, mem_size);
- wl12xx_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
- reg_start, reg_size);
- }
-
- partition[0].start = mem_start;
- partition[0].size = mem_size;
- partition[1].start = reg_start;
- partition[1].size = reg_size;
-
- wl->physical_mem_addr = mem_start;
- wl->physical_reg_addr = reg_start;
-
- wl->virtual_mem_addr = 0;
- wl->virtual_reg_addr = mem_size;
-
- t.tx_buf = tx_buf;
- t.len = sizeof(tx_buf);
- spi_message_add_tail(&t, &m);
-
- spi_sync(wl->spi, &m);
-}
-
static void wl12xx_spi_read(struct wl12xx *wl, int addr, void *buf,
size_t len)
{
diff --git a/drivers/net/wireless/wl12xx/spi.h b/drivers/net/wireless/wl12xx/spi.h
index 761401b..1cbedcf 100644
--- a/drivers/net/wireless/wl12xx/spi.h
+++ b/drivers/net/wireless/wl12xx/spi.h
@@ -29,17 +29,6 @@
#include "acx.h"
#include "reg.h"
-#define HW_ACCESS_MEMORY_MAX_RANGE 0x1FFC0
-
-#define HW_ACCESS_PART0_SIZE_ADDR 0x1FFC0
-#define HW_ACCESS_PART0_START_ADDR 0x1FFC4
-#define HW_ACCESS_PART1_SIZE_ADDR 0x1FFC8
-#define HW_ACCESS_PART1_START_ADDR 0x1FFCC
-
-#define HW_ACCESS_REGISTER_SIZE 4
-
-#define HW_ACCESS_PRAM_MAX_RANGE 0x3c000
-
#define WSPI_CMD_READ 0x40000000
#define WSPI_CMD_WRITE 0x00000000
#define WSPI_CMD_FIXED 0x20000000
--
1.6.0.6
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
