Hi,
I have tested with the latest kernel 2.6.27.10 and compat-wireless 22-12-2008.
I have a dual core system (Intel(R) Pentium(R) 4 CPU 3.00GHz) and use hostapd
0.6.6.
I have build the kernel, compiled the compat-wireless and did a make install.
Make unload didnt work because some drivers were in use (mac80211).
First problem arises, a rmmod ath9k hangs the kernel. No message of what so
ever in the log or to stdout.
Rebooted the system (hostapd still disabled). Iwconfig shows:
wlan0 IEEE 802.11bgn ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=27 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
If I start hostapd (by hand or from init.d) the kernel hangs with no trace of
such thing. Hostapd shows in stdout (with -dd):
Configuration file: /etc/hostapd/hostapd.conf
ctrl_interface_group=0
Opening raw packet socket for ifindex 1688
BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits)
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
Allowed channel: mode=1 chan=1 freq=2412 MHz
Allowed channel: mode=1 chan=2 freq=2417 MHz
Allowed channel: mode=1 chan=3 freq=2422 MHz
Allowed channel: mode=1 chan=4 freq=2427 MHz
Allowed channel: mode=1 chan=5 freq=2432 MHz
Allowed channel: mode=1 chan=6 freq=2437 MHz
Allowed channel: mode=1 chan=7 freq=2442 MHz
Allowed channel: mode=1 chan=8 freq=2447 MHz
Allowed channel: mode=1 chan=9 freq=2452 MHz
Allowed channel: mode=1 chan=10 freq=2457 MHz
Allowed channel: mode=1 chan=11 freq=2462 MHz
Failed to update rate sets in kernel module
RATE[0] rate=10 flags=0x2
RATE[1] rate=20 flags=0x2
RATE[2] rate=55 flags=0x2
RATE[3] rate=110 flags=0x2
RATE[4] rate=60 flags=0x0
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x0
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x0
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
Passive scanning not supported
Flushing old station entries
I have tried in the past several kernelversions and compat-wireless versions
and all give the same problem.
So I think it is hardware (system) related and ap-mode.
How can I trace the problem? Default I get no entries in any log.
lspci -vv shows
04:08.0 Network controller: Atheros Communications Inc. AR5416 802.11abgn
Wireless PCI Adapter (rev 01)
Subsystem: Linksys Device 0061
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0310000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] #80 [0000]
Kernel driver in use: ath9k
Kernel modules: ath9k
Can somebody provide some help. I am struggeling to get the card into ap mode.
TIA,
Willem
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
