wt., 3 gru 2024 o 11:57 Yu Zhang (Yuriy) <quic_yuzha@xxxxxxxxxxx> napisał(a):
>
>
>
> On 12/3/2024 5:48 PM, Jose Ignacio Tornos Martinez wrote:
> >> Which chip do you use?
> > Since I am not totally sure about the useful information, let me show you
> > the kernel logs:
> > $ dmesg | grep ath11k
> > [ 3.659388] ath11k_pci 0000:01:00.0: BAR 0 [mem 0x84200000-0x843fffff 64bit]: assigned
> > [ 3.659405] ath11k_pci 0000:01:00.0: enabling device (0000 -> 0002)
> > [ 3.659649] ath11k_pci 0000:01:00.0: MSI vectors: 32
> > [ 3.659653] ath11k_pci 0000:01:00.0: wcn6855 hw2.1
> > [ 4.871571] ath11k_pci 0000:01:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0210
> > [ 4.871586] ath11k_pci 0000:01:00.0: fw_version 0x11088c35 fw_build_timestamp 2024-04-17 08:34 fw_build_id WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
> > [ 5.241485] ath11k_pci 0000:01:00.0 wlp1s0: renamed from wlan0
> >
> yes, you also use wcn6855 hw2.1.
> > If I try to setup 2 APs with your interface combination I get this:
> > # iw list | grep -A6 "valid interface combinations:"
> > valid interface combinations:
> > * #{ managed } <= 2, #{ AP, P2P-client, P2P-GO } <= 16, #{ P2P-device } <= 1,
> > total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
> >
> > * #{ managed } <= 2, #{ AP, P2P-client, P2P-GO } <= 16, #{ P2P-device } <= 1,
> > total <= 3, #channels <= 2, STA/AP BI must match
> > HT Capability overrides:
> 2 combinations are to support DBS and DFS.
> Combinations is correct. channels=2, max interfaces=3.
>
Small question from my side. If phyX will support 3 bands (2.4/5/6)
what this channes<=2 limitation mean here for APs?
a) can I setup APs on 2412 and 5180
b) or even can setup APs on 2412 and 2462?
c) or setup APs on 5180 and 6055?
How could I know a or b or c is allowed?
BTW, do you plan to share same firmware (with 2 possible APs) for
ath12k and WCN7850?
BR
Janusz
> And you want setup sta + sap + sap, right?
> When up the second sap will meet error? Could you pls share the error logs?
>
> I'm not very sure if you add all interface with managed type, and do
> "ifconfig xxx up" before running hostapd.
>
> You can try add second and third interface with
> "iw dev xx interface add xx type __ap".
>
>
> > # iw dev
> > phy#0
> > Interface wlp1s0_1
> > ifindex 6
> > wdev 0x4
> > addr a2:42:d2:1e:89:a3
> > type managed
> > txpower 16.00 dBm
> > multicast TXQ:
> > qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
> > 0 0 0 0 0 0 0 0 0
> > Interface wlp1s0_0
> > ifindex 5
> > wdev 0x3
> > addr 52:e9:be:33:6a:61
> > ssid test-qe-wpa2-psk
> > type AP
> > channel 13 (2472 MHz), width: 20 MHz, center1: 2472 MHz
> > txpower 14.00 dBm
> > multicast TXQ:
> > qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
> > 0 0 0 0 0 0 0 0 0
> > Interface wlp1s0
> > ifindex 3
> > wdev 0x1
> > addr c8:94:02:b5:fe:fb
> > type managed
> > txpower 16.00 dBm
> > multicast TXQ:
> > qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
> > 0 0 0 0 0 0 0 0 0
> > Or even this with no AP up:
> > # iw dev
> > phy#0
> > Interface wlp1s0_1
> > ifindex 6
> > wdev 0x4
> > addr ca:e5:84:22:10:ec
> > type managed
> > txpower 16.00 dBm
> > multicast TXQ:
> > qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
> > 0 0 0 0 0 0 0 0 0
> > Interface wlp1s0_0
> > ifindex 5
> > wdev 0x3
> > addr 9e:4e:c5:ea:4c:e9
> > type AP
> > txpower 16.00 dBm
> > multicast TXQ:
> > qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
> > 0 0 0 0 0 0 0 0 0
> > Interface wlp1s0
> > ifindex 3
> > wdev 0x1
> > addr c8:94:02:b5:fe:fb
> > type managed
> > txpower 16.00 dBm
> > multicast TXQ:
> > qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
> > 0 0 0 0 0 0 0 0 0
> >
> > If I use the parameter to ignore the feature and configure the interface combination as before:
> > # iw list | grep -A4 "valid interface combinations:"
> > valid interface combinations:
> > * #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 16, #{ P2P-device } <= 1,
> > total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz }
> >
> > HT Capability overrides:
> > # iw dev
> > phy#1
> > Interface wlp1s0_1
> > ifindex 7
> > wdev 0x100000004
> > addr 82:90:89:90:c1:37
> > ssid test-qe-wpa3-psk
> > type AP
> > channel 13 (2472 MHz), width: 20 MHz, center1: 2472 MHz
> > txpower 16.00 dBm
> > multicast TXQ:
> > qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
> > 0 0 0 0 0 0 0 0 0
> > Interface wlp1s0_0
> > ifindex 6
> > wdev 0x100000003
> > addr 6a:ef:d0:db:10:f0
> > ssid test-qe-wpa2-psk
> > type AP
> > channel 13 (2472 MHz), width: 20 MHz, center1: 2472 MHz
> > txpower 16.00 dBm
> > multicast TXQ:
> > qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
> > 0 0 0 0 0 0 0 0 0
> > Interface wlp1s0
> > ifindex 4
> > wdev 0x100000001
> > addr c8:94:02:b5:fe:fb
> > type managed
> > txpower 16.00 dBm
> > multicast TXQ:
> > qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
> > 0 0 0 0 0 0 0 0 0
> >
> > Thanks
> >
> > Best regards
> > Jose Ignacio
> >
>
>
--
Janusz Dziedzic
