On 9/25/2024 1:11 AM, Remi Pommarel wrote:
On full monitor HW the monitor destination rxdma ring does not have the
same descriptor format as in the "classical" mode. The full monitor
destination entries are of hal_sw_monitor_ring type and fetched using
ath11k_dp_full_mon_process_rx while the classical ones are of type
hal_reo_entrance_ring and fetched with ath11k_dp_rx_mon_dest_process.
Although both hal_sw_monitor_ring and hal_reo_entrance_ring are of same
size, the offset to useful info (such as sw_cookie, paddr, etc) are
different. Thus if ath11k_dp_rx_mon_dest_process gets called on full
monitor destination ring, invalid skb buffer id will be fetched from DMA
ring causing issues such as the following rcu_sched stall:
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 0-....: (1 GPs behind) idle=c67/0/0x7 softirq=45768/45769 fqs=1012
(t=2100 jiffies g=14817 q=8703)
Task dump for CPU 0:
task:swapper/0 state:R running task stack: 0 pid: 0 ppid: 0 flags:0x0000000a
Call trace:
dump_backtrace+0x0/0x160
show_stack+0x14/0x20
sched_show_task+0x158/0x184
dump_cpu_task+0x40/0x4c
rcu_dump_cpu_stacks+0xec/0x12c
rcu_sched_clock_irq+0x6c8/0x8a0
update_process_times+0x88/0xd0
tick_sched_timer+0x74/0x1e0
__hrtimer_run_queues+0x150/0x204
hrtimer_interrupt+0xe4/0x240
arch_timer_handler_phys+0x30/0x40
handle_percpu_devid_irq+0x80/0x130
handle_domain_irq+0x5c/0x90
gic_handle_irq+0x8c/0xb4
do_interrupt_handler+0x30/0x54
el1_interrupt+0x2c/0x4c
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x74/0x78
do_raw_spin_lock+0x60/0x100
_raw_spin_lock_bh+0x1c/0x2c
ath11k_dp_rx_mon_mpdu_pop.constprop.0+0x174/0x650
ath11k_dp_rx_process_mon_status+0x8b4/0xa80
ath11k_dp_rx_process_mon_rings+0x244/0x510
ath11k_dp_service_srng+0x190/0x300
ath11k_pcic_ext_grp_napi_poll+0x30/0xc0
__napi_poll+0x34/0x174
net_rx_action+0xf8/0x2a0
_stext+0x12c/0x2ac
irq_exit+0x94/0xc0
handle_domain_irq+0x60/0x90
gic_handle_irq+0x8c/0xb4
call_on_irq_stack+0x28/0x44
do_interrupt_handler+0x4c/0x54
el1_interrupt+0x2c/0x4c
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x74/0x78
arch_cpu_idle+0x14/0x20
do_idle+0xf0/0x130
cpu_startup_entry+0x24/0x50
rest_init+0xf8/0x104
arch_call_rest_init+0xc/0x14
start_kernel+0x56c/0x58c
__primary_switched+0xa0/0xa8
Thus ath11k_dp_rx_mon_dest_process(), which use classical destination
entry format, should no be called on full monitor capable HW.
Thanks, it looks good to me.
Reviewed-by: Praneesh P <quic_ppranees@xxxxxxxxxxx>
Fixes: 67a9d399fcb0 ("ath11k: enable RX PPDU stats in monitor co-exist mode")
Signed-off-by: Remi Pommarel <repk@xxxxxxxxxxxx>
---
v2: set ppdu_status to DP_PPDU_STATUS_DONE as suggested by
https://lore.kernel.org/ath11k/d376023d-267a-4512-8749-f816fefeb842@xxxxxxxxxxx/
drivers/net/wireless/ath/ath11k/dp_rx.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/ath11k/dp_rx.c b/drivers/net/wireless/ath/ath11k/dp_rx.c
index c087d8a0f5b2..40088e62572e 100644
--- a/drivers/net/wireless/ath/ath11k/dp_rx.c
+++ b/drivers/net/wireless/ath/ath11k/dp_rx.c
@@ -5291,8 +5291,11 @@ int ath11k_dp_rx_process_mon_status(struct ath11k_base *ab, int mac_id,
hal_status == HAL_TLV_STATUS_PPDU_DONE) {
rx_mon_stats->status_ppdu_done++;
pmon->mon_ppdu_status = DP_PPDU_STATUS_DONE;
- ath11k_dp_rx_mon_dest_process(ar, mac_id, budget, napi);
- pmon->mon_ppdu_status = DP_PPDU_STATUS_START;
+ if (!ab->hw_params.full_monitor_mode) {
+ ath11k_dp_rx_mon_dest_process(ar, mac_id,
+ budget, napi);
+ pmon->mon_ppdu_status = DP_PPDU_STATUS_START;
+ }
}
if (ppdu_info->peer_id == HAL_INVALID_PEERID ||
