On Monday 08 December 2008 08:49:04 Manuel Lauss wrote: > Hello, Hello! > The following oops occurs when udev loads p54pci driver (device is an early > SM2802W V2 PCI with the isl3886 "softmac" chip; 2.6.28-rc7, firmware > 2.13.1.0.arm). This is transcribed from a rather bad photo (please see > http://mlau.at/pix/p54oops.jpg ): > > BUG: Unable to handle kernel NULL pointer dereference at 0000000000000000 > IP: [<ffffffffa0016b66>] p54_rx+0xc6/0x490 [p54common] > PGD 12e433067 PUD 12e46f067 PMD 0 > Oops: 0000 [#1] PREEMPT SMP > last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0:0/.... > CPU 0 > Modules linked in: usb_storage ohci1394(+) ieee1394 p54pci(+) p54common ahci... > Pid: 0, comm: swapper Not tainted 2.6.28-rc7-00091-gf6f7b52 #1 > RIP: 0010:[<ffffffffa0016b66>] [<ffffffffa0016b66>] p54_rx+0xc6/0x490 [p54common] > RSP: 0018:ffffffff80ab3df0 EFLAGS: 00010207 > RAX: 0000000074e9fed0 RBX: ffff08012e4f1940 RCX: 0000000000002e10 > RDX: 0000000000000000 RSI: 00000000000000f1 RDI: ffff80012e4f0000 > RBP: ffff80012e077010 R08: ffff80012e077000 R09: ffff80012e04?000 > R10: 0000000000000001 R11: ffffffff00221320 R12: ffff80012e4f1900 > R13: ffff80012e4f0300 R14: 000000000000732e R15: ffff80012e4f19?? > > (gdb) list *p54_rx+0xc6 > 0x1b66 is in p54_rx (/usr/src/linux-2.6.git/drivers/net/wireless/p54/p54common.c:502). > 497 > 498 rx_status.signal = p54_rssi_to_dbm(dev, hdr->rssi); > 499 rx_status.noise = priv->noise; > 500 /* XX correct? */ > 501 rx_status.qual = (100 * hdr->rssi) / 127; > 502 rx_status.rate_idx = (dev->conf.channel->band == IEEE80211_BAND_2GHZ ? > 503 hdr->rate : (hdr->rate - 4)) & 0xf; That's right, dev->conf.channel isn't set at the time we're reading the eeprom. But, then we didn't initialize the radio, dcf and mac/bb yet, so where did the data frames came from? > Loading the module manually gets a bit further: > > p54pci 0000:05:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > p54pci 0000:05:01.0: firmware: requesting isl3886 > p54: LM86 firmware > p54: FW rev 2.13.1.0 - Softmac protocol 5.5 > phy2: device does not respond! --- no, this time it just doesn't respond at all => crashed > p54pci 0000:05:01.0: PCI INT A disabled > p54pci: probe of 0000:05:01.0 failed with error -16 Did it work with an older firmware? (and then which one?) Or do you have >= 4GB Ram/iommu etc.? Regards, Chr -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
