From: Wen Gong <quic_wgong@xxxxxxxxxxx>
When station is connected to a 6 GHz AP, it has 2 ways to configure
the power limit to firmware. The first way is to send 2 WMI commands
WMI_PDEV_PARAM_TXPOWER_LIMIT2G/WMI_PDEV_PARAM_TXPOWER_LIMIT5G to
firmware, the second way is to send WMI_VDEV_SET_TPC_POWER_CMDID to
firmware which include more parameters for power control.
When firmware support SERVICE_EXT_TPC_REG, it means firmware support
the second way for WMI_VDEV_SET_TPC_POWER_CMDID, then ath11k discard
BSS_CHANGED_TXPOWER flag from mac80211 which is used to the first way
for 6 GHz band and select the second way.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@xxxxxxxxxxx>
Signed-off-by: Baochen Qiang <quic_bqiang@xxxxxxxxxxx>
---
v7:
1. squash original patch 11 and patch 13.
2. s/wmi command/WMI commands/
3. s/way/ways/
4. add TODO tag for CSA.
drivers/net/wireless/ath/ath11k/mac.c | 33 +++++++++++++++++++++++----
1 file changed, 29 insertions(+), 4 deletions(-)
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index 2520f78c9c0b..254cb0427d12 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -3397,6 +3397,18 @@ static int ath11k_mac_config_obss_pd(struct ath11k *ar,
return 0;
}
+static bool ath11k_mac_supports_station_tpc(struct ath11k *ar,
+ struct ath11k_vif *arvif,
+ const struct cfg80211_chan_def *chandef)
+{
+ return ath11k_wmi_supports_6ghz_cc_ext(ar) &&
+ test_bit(WMI_TLV_SERVICE_EXT_TPC_REG_SUPPORT, ar->ab->wmi_ab.svc_map) &&
+ arvif->vdev_type == WMI_VDEV_TYPE_STA &&
+ arvif->vdev_subtype == WMI_VDEV_SUBTYPE_NONE &&
+ chandef->chan &&
+ chandef->chan->band == NL80211_BAND_6GHZ;
+}
+
static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *info,
@@ -3596,9 +3608,13 @@ static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
if (changed & BSS_CHANGED_TXPOWER) {
ath11k_dbg(ar->ab, ATH11K_DBG_MAC, "vdev_id %i txpower %d\n",
arvif->vdev_id, info->txpower);
-
- arvif->txpower = info->txpower;
- ath11k_mac_txpower_recalc(ar);
+ if (ath11k_mac_supports_station_tpc(ar, arvif, &info->chandef)) {
+ ath11k_dbg(ar->ab, ATH11K_DBG_MAC,
+ "discard tx power, change to set TPC power\n");
+ } else {
+ arvif->txpower = info->txpower;
+ ath11k_mac_txpower_recalc(ar);
+ }
}
if (changed & BSS_CHANGED_PS &&
@@ -7279,6 +7295,15 @@ ath11k_mac_vdev_start_restart(struct ath11k_vif *arvif,
return ret;
}
+ /* TODO: For now we only set TPC power here. However when
+ * channel changes, say CSA, it should be updated again.
+ */
+ if (ath11k_mac_supports_station_tpc(ar, arvif, chandef)) {
+ ath11k_mac_fill_reg_tpc_info(ar, arvif->vif, &arvif->chanctx);
+ ath11k_wmi_send_vdev_set_tpc_power(ar, arvif->vdev_id,
+ &arvif->reg_tpc_info);
+ }
+
if (!restart)
ar->num_started_vdevs++;
@@ -8093,7 +8118,7 @@ ath11k_mac_op_assign_vif_chanctx(struct ieee80211_hw *hw,
goto out;
}
ath11k_reg_handle_chan_list(ab, reg_info, power_type);
-
+ arvif->chanctx = *ctx;
ath11k_mac_parse_tx_pwr_env(ar, vif, ctx);
}
--
2.25.1
