On 9/20/23 13:53, Wen Gong wrote:
When station is connected to a 6 GHz AP, it has 2 way to configure
the power limit to firmware. The first way is to send 2 wmi command
WMI_PDEV_PARAM_TXPOWER_LIMIT2G/WMI_PDEV_PARAM_TXPOWER_LIMIT5G to
firmware, the second way is to send WMI_VDEV_SET_TPC_POWER_CMDID to
firmware which include more parameters for power control.
When firmware support SERVICE_EXT_TPC_REG, it means firmware support
the second way for WMI_VDEV_SET_TPC_POWER_CMDID, then ath11k discard
BSS_CHANGED_TXPOWER flag from mac80211 which is used to the first way
for 6 GHz band in this patch and select the second way in the subsequent
patch.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@xxxxxxxxxxx>
---
drivers/net/wireless/ath/ath11k/mac.c | 22 +++++++++++++++++++---
1 file changed, 19 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index f05d66913abd..a8ae281d2635 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -3396,6 +3396,18 @@ static int ath11k_mac_config_obss_pd(struct ath11k *ar,
return 0;
}
+static bool ath11k_mac_supports_station_tpc(struct ath11k *ar,
+ struct ath11k_vif *arvif,
+ const struct cfg80211_chan_def *chandef)
+{
+ return ath11k_mac_supports_6ghz_cc_ext(ar) &&
+ test_bit(WMI_TLV_SERVICE_EXT_TPC_REG_SUPPORT, ar->ab->wmi_ab.svc_map) &&
+ arvif->vdev_type == WMI_VDEV_TYPE_STA &&
+ arvif->vdev_subtype == WMI_VDEV_SUBTYPE_NONE &&
+ chandef->chan &&
+ chandef->chan->band == NL80211_BAND_6GHZ;
+}
+
static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *info,
@@ -3595,9 +3607,13 @@ static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
if (changed & BSS_CHANGED_TXPOWER) {
ath11k_dbg(ar->ab, ATH11K_DBG_MAC, "vdev_id %i txpower %d\n",
arvif->vdev_id, info->txpower);
-
- arvif->txpower = info->txpower;
- ath11k_mac_txpower_recalc(ar);
+ if (ath11k_mac_supports_station_tpc(ar, arvif, &info->chandef)) {
So even if user wants to operate in low power value, we won't be
allowing to do that in case of 6 GHz station mode? Only TPC power is valid?
+ ath11k_dbg(ar->ab, ATH11K_DBG_MAC,
+ "discard tx power, change to set TPC power\n");
+ } else {
+ arvif->txpower = info->txpower;
+ ath11k_mac_txpower_recalc(ar);
+ }
}
if (changed & BSS_CHANGED_PS &&
