On 5/3/23 02:13, Alexey Kardashevskiy wrote:
Hi!
I am seeing dropouts in 5GHz and 2.5GHz wifi and seeking for help.
HP laptop with RTL8822CE 802.11ac PCIe Wireless Network Adapter, Fedora36 with
6.2.9-100.fc36.x86_64, the AP is Ubiquity, it is 5m away behind a thin wall, a
house in low density area (I do not see neighbors APs in "iw dev scan").
Pinging a gateway (1gbit ethernet between AP and GW) suddenly goes from 3-5ms to
>1000ms. Good and bad "iw" output is below. Moving laptop by 2cm (or its lid)
helps sometime.
These 2 observation made me suspect the linux driver:
1) If I reboot the laptop to Windows10 without moving/touching it after it went
bad in linux - there pings are 1-2ms and occasionally may go up to hundreds but
for a very short time, feels like the driver notices something and fixes it.
2) Two other laptops with Intel Wifi cards on the same spot with the same fedora
on the same network do not show the problem at all.
Changing txpower 10..23dBm (where 2300 is the maximum) does not help, done via
"iw dev wlp1s0 set txpower limit 2300", "iw dev wlp1s0 info" confirms that it
changes.
I have these in /etc/modprobe.d/50-rtw88.conf
options rtw88_core disable_lps_deep=y
options rtw88_pci disable_aspm=y
no change either.
Is there anything else to try? Thanks,
64 bytes from _gateway (192.168.10.200): icmp_seq=26 ttl=64 time=6.97 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=27 ttl=64 time=3.68 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=28 ttl=64 time=3.44 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=29 ttl=64 time=3.97 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=30 ttl=64 time=3.68 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=31 ttl=64 time=17.0 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=32 ttl=64 time=33.1 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=33 ttl=64 time=697 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=34 ttl=64 time=1130 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=35 ttl=64 time=114 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=36 ttl=64 time=1796 ms
64 bytes from _gateway (192.168.10.200): icmp_seq=37 ttl=64 time=749 ms
Good status:
[root@aiemdeew wlp1s0]# iw dev wlp1s0 info ; iw wlp1s0 link
Interface wlp1s0
ifindex 2
wdev 0x1
addr 50:c2:e8:5d:ba:fd
type managed
wiphy 0
channel 36 (5180 MHz), width: 80 MHz, center1: 5210 MHz
txpower 22.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol
tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
Connected to f4:92:bf:04:1a:ce (on wlp1s0)
SSID: aikhomenet
freq: 5180
RX: 37035326 bytes (60439 packets)
TX: 2880943 bytes (14231 packets)
signal: -53 dBm
rx bitrate: 130.0 MBit/s VHT-MCS 7 VHT-NSS 2
tx bitrate: 390.0 MBit/s VHT-MCS 4 80MHz short GI VHT-NSS 2
bss flags: short-slot-time
dtim period: 2
beacon int: 100
Bad status:
Interface wlp1s0
ifindex 2
wdev 0x1
addr 50:c2:e8:5d:ba:fd
type managed
wiphy 0
channel 36 (5180 MHz), width: 80 MHz, center1: 5210 MHz
txpower 22.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol
tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
Connected to f4:92:bf:04:1a:ce (on wlp1s0)
SSID: aikhomenet
freq: 5180
RX: 38078401 bytes (68758 packets)
TX: 3039702 bytes (15006 packets)
signal: -62 dBm
rx bitrate: 117.0 MBit/s VHT-MCS 6 VHT-NSS 2
tx bitrate: 433.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 1
bss flags: short-slot-time
dtim period: 2
beacon int: 100
Something certainly changed for your signal strength to drop from -53 to -62
dBm. The higher value is acceptable, but will not provide high data rates. The
lower value is marginal.
There are some changes between kernel 6.2 and the current contents of the
wireless-next repo, which is the code to be found in kernel 6.4 when it is
released. Could you try the code in https://github.com/lwfinger/rtw88.git? This
repo has the code found in wireless-next modified to build on older kernels. You
would need to blacklist rtw88_8822ce. This sequence should do it for you:
sudo dnf install git kernel-headers kernel-devel
sudo dnf group install "C Development Tools and Libraries"
git clone https://github.com/lwfinger/rtw88.git
cd rtw88
make
sudo make install
sudo touch /usr/lib/modprobe.d/50-blacklist-8822ce.conf
As root, using your favorite editor, add the following line to the above file:
blacklist rtw88_8822ce
Then reboot. Report if there are any changes. This way, we will be able to
determine if the problem has already been fixed.
Larry
