Search Linux Wireless

[PATCH v2] wifi: ath11k: Optimize 6 GHz scan time

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Currently, time taken to scan all supported channels on WCN6750
is ~8 seconds and connection time is almost 10 seconds. WCN6750
supports three Wi-Fi bands (i.e., 2.4/5/6 GHz) and the numbers of
channels for scan come around ~100 channels (default case).
Since the chip doesn't have support for DBS (Dual Band Simultaneous),
scans cannot be parallelized resulting in longer scan times.

Among the 100 odd channels, ~60 channels are in 6 GHz band. Therefore,
optimizing the scan for 6 GHz channels will bring down the overall
scan time.

WCN6750 firmware has support to scan a 6 GHz channel based on co-located
AP information i.e., RNR IE which is found in the legacy 2.4/5 GHz scan
results. When a scan request with all supported channel list is enqueued
to the firmware, then based on WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND
scan channel flag, firmware will scan only those 6 GHz channels for which
RNR IEs are found in the legacy scan results.

In the proposed design, based on NL80211_SCAN_FLAG_COLOCATED_6GHZ scan
flag, driver will set the WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND flag
for non-PSC channels. Since there is high probability to find 6 GHz APs
on PSC channels, these channels are always scanned. Only non-PSC channels
are selectively scanned based on cached RNR information from the legacy
scan results.

If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set in the scan flags,
then scan will happen on all supported channels (default behavior).

With these optimizations, scan time is improved by 1.5-1.8 seconds on
WCN6750. Similar savings have been observed on WCN6855.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@xxxxxxxxxxx>
---
V2:
 - Rebased on ToT

 drivers/net/wireless/ath/ath11k/mac.c | 25 +++++++++++++++++++++++--
 drivers/net/wireless/ath/ath11k/wmi.h |  4 ++++
 2 files changed, 27 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index cad832e0e6b8..ce5a7a912a10 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -3819,8 +3819,29 @@ static int ath11k_mac_op_hw_scan(struct ieee80211_hw *hw,
 			goto exit;
 		}
 
-		for (i = 0; i < arg->num_chan; i++)
-			arg->chan_list[i] = req->channels[i]->center_freq;
+		for (i = 0; i < arg->num_chan; i++) {
+			if (test_bit(WMI_TLV_SERVICE_SCAN_CONFIG_PER_CHANNEL,
+				     ar->ab->wmi_ab.svc_map)) {
+				arg->chan_list[i] =
+					u32_encode_bits(req->channels[i]->center_freq,
+							WMI_SCAN_CONF_PER_CH_CHANNEL_MASK);
+
+				/* If NL80211_SCAN_FLAG_COLOCATED_6GHZ is set in scan
+				 * flags, then scan all PSC channels in 6 GHz band and
+				 * those non-PSC channels where RNR IE is found during
+				 * the legacy 2.4/5 GHz scan.
+				 * If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set,
+				 * then all channels in 6 GHz will be scanned.
+				 */
+				if (req->channels[i]->band == NL80211_BAND_6GHZ &&
+				    req->flags & NL80211_SCAN_FLAG_COLOCATED_6GHZ &&
+				    !cfg80211_channel_is_psc(req->channels[i]))
+					arg->chan_list[i] |=
+						WMI_SCAN_CH_FLAG_SCAN_ONLY_IF_RNR_FOUND;
+			} else {
+				arg->chan_list[i] = req->channels[i]->center_freq;
+			}
+		}
 	}
 
 	if (req->flags & NL80211_SCAN_FLAG_RANDOM_ADDR) {
diff --git a/drivers/net/wireless/ath/ath11k/wmi.h b/drivers/net/wireless/ath/ath11k/wmi.h
index 63dbb085949f..584824e367db 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.h
+++ b/drivers/net/wireless/ath/ath11k/wmi.h
@@ -2097,6 +2097,7 @@ enum wmi_tlv_service {
 
 	/* The second 128 bits */
 	WMI_MAX_EXT_SERVICE = 256,
+	WMI_TLV_SERVICE_SCAN_CONFIG_PER_CHANNEL = 265,
 	WMI_TLV_SERVICE_BIOS_SAR_SUPPORT = 326,
 
 	/* The third 128 bits */
@@ -3232,6 +3233,9 @@ struct  wmi_start_scan_cmd {
 #define WMI_SCAN_DWELL_MODE_SHIFT        21
 #define WMI_SCAN_FLAG_EXT_PASSIVE_SCAN_START_TIME_ENHANCE   0x00000800
 
+#define WMI_SCAN_CONF_PER_CH_CHANNEL_MASK	GENMASK(19, 0)
+#define WMI_SCAN_CH_FLAG_SCAN_ONLY_IF_RNR_FOUND	BIT(20)
+
 enum {
 	WMI_SCAN_DWELL_MODE_DEFAULT      = 0,
 	WMI_SCAN_DWELL_MODE_CONSERVATIVE = 1,

base-commit: 1a304987a22c9f383f163f93beb47e89080d1cee
-- 
2.38.0




[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Wireless Regulations]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux