+ Johannes On 12/30/2022 6:39 PM, Stefan Wahren wrote:
Hi,since Linux 6.2-rc1 i noticed on my Raspberry Pi 3 B+ (arm/multi_v7_defconfig) the following new error messages appear, even if there is no Wifi connection. I suspect this is not a real issue, so it would nice to get the rid of it:[ 26.303445] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 26.303554] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,3-model-b-plus.bin failed with error -2[ 26.516752] brcmfmac_wcc: brcmf_wcc_attach: executing[ 26.528264] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Jan 4 2021 19:56:29 version 7.45.229 (617f1f5 CY) FWID 01-2dbd9d2e[ 27.076829] Bluetooth: hci0: BCM: features 0x2f [ 27.078592] Bluetooth: hci0: BCM43455 37.4MHz Raspberry Pi 3+ [ 27.078601] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0342[ 30.142104] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SS[ 30.590017] Bluetooth: MGMT ver 1.22[ 104.897615] brcmfmac: cfg80211_set_channel: set chanspec 0x100e fail, reason -52 [ 104.897992] brcmfmac: cfg80211_set_channel: set chanspec 0xd022 fail, reason -52 [ 105.007672] brcmfmac: cfg80211_set_channel: set chanspec 0xd026 fail, reason -52 [ 105.117654] brcmfmac: cfg80211_set_channel: set chanspec 0xd02a fail, reason -52 [ 105.227636] brcmfmac: cfg80211_set_channel: set chanspec 0xd02e fail, reason -52 [ 106.987552] brcmfmac: cfg80211_set_channel: set chanspec 0xd090 fail, reason -52 [ 106.987911] brcmfmac: cfg80211_set_channel: set chanspec 0xd095 fail, reason -52 [ 106.988233] brcmfmac: cfg80211_set_channel: set chanspec 0xd099 fail, reason -52 [ 106.988565] brcmfmac: cfg80211_set_channel: set chanspec 0xd09d fail, reason -52 [ 106.988909] brcmfmac: cfg80211_set_channel: set chanspec 0xd0a1 fail, reason -52All of these 10 errors are repeated every 60 sec.
Catching up after the holidays ;-) Above chanspec values are invalid. 0x100e = channel 14/bw 20MHz. The 'iw list' output shows all these channels are disabled. So who/what is trying to set these channels. Scanning sets the channel in firmware. Is this initiated from hostapd? Maybe trying ACS? As these are marked as disabled user-space should not use them. What I don't understand is why these pass the cfg80211 layer so adding Johannes here.
Regards, Arend
If i enable the debugging for brcmf_fil_cmd_data, i'm getting this: [ 107.069199] brcmfmac: Firmware error: BCME_BADCHAN (-20)[ 107.069232] brcmfmac: cfg80211_set_channel: set chanspec 0x100e fail, reason -52[ 107.069597] brcmfmac: Firmware error: BCME_BADCHAN (-20)[ 107.069610] brcmfmac: cfg80211_set_channel: set chanspec 0xd022 fail, reason -52... Here some additional information: $ iw info Interface wlan0 ifindex 4 wdev 0x1 addr b8:27:eb:2e:ec:42 type managed wiphy 0 channel 140 (5700 MHz), width: 20 MHz, center1: 5700 MHz txpower 31.00 dBm $ iw reg get global country DE: DFS-ETSI (2400 - 2483 @ 40), (N/A, 20), (N/A) (5150 - 5250 @ 80), (N/A, 20), (N/A), NO-OUTDOOR, AUTO-BW (5250 - 5350 @ 80), (N/A, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW (5470 - 5725 @ 160), (N/A, 26), (0 ms), DFS (5725 - 5875 @ 80), (N/A, 13), (N/A) (57000 - 66000 @ 2160), (N/A, 40), (N/A) phy#0 country 99: DFS-UNSET (2402 - 2482 @ 40), (6, 20), (N/A) (2474 - 2494 @ 20), (6, 20), (N/A) (5140 - 5360 @ 160), (6, 20), (N/A) (5460 - 5860 @ 160), (6, 20), (N/A) $ iw list Wiphy phy0 max # scan SSIDs: 10 max scan IEs length: 2048 bytes max # sched scan SSIDs: 16 max # match sets: 16 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports roaming. Device supports T-DLS. Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP-128 (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * P2P-client * P2P-GO * P2P-device Band 1: Capabilities: 0x1062 HT20/HT40 Static SM Power Save RX HT20 SGI RX HT40 SGI No RX STBC Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 16 usec (0x07) HT TX/RX MCS rate indexes supported: 0-7 Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) * 2472 MHz [13] (20.0 dBm) * 2484 MHz [14] (disabled) Band 2: Capabilities: 0x1062 HT20/HT40 Static SM Power Save RX HT20 SGI RX HT40 SGI No RX STBC Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 16 usec (0x07) HT TX/RX MCS rate indexes supported: 0-7 VHT Capabilities (0x00001020): Max MPDU length: 3895 Supported Channel Width: neither 160 nor 80+80 short GI (80 MHz) SU Beamformee VHT RX MCS set: 1 streams: MCS 0-9 2 streams: not supported 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT RX highest supported: 0 Mbps VHT TX MCS set: 1 streams: MCS 0-9 2 streams: not supported 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT TX highest supported: 0 Mbps Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Frequencies: * 5170 MHz [34] (disabled) * 5180 MHz [36] (20.0 dBm) * 5190 MHz [38] (disabled) * 5200 MHz [40] (20.0 dBm) * 5210 MHz [42] (disabled) * 5220 MHz [44] (20.0 dBm) * 5230 MHz [46] (disabled) * 5240 MHz [48] (20.0 dBm) * 5260 MHz [52] (20.0 dBm) (no IR, radar detection) * 5280 MHz [56] (20.0 dBm) (no IR, radar detection) * 5300 MHz [60] (20.0 dBm) (no IR, radar detection) * 5320 MHz [64] (20.0 dBm) (no IR, radar detection) * 5500 MHz [100] (20.0 dBm) (no IR, radar detection) * 5520 MHz [104] (20.0 dBm) (no IR, radar detection) * 5540 MHz [108] (20.0 dBm) (no IR, radar detection) * 5560 MHz [112] (20.0 dBm) (no IR, radar detection) * 5580 MHz [116] (20.0 dBm) (no IR, radar detection) * 5600 MHz [120] (20.0 dBm) (no IR, radar detection) * 5620 MHz [124] (20.0 dBm) (no IR, radar detection) * 5640 MHz [128] (20.0 dBm) (no IR, radar detection) * 5660 MHz [132] (20.0 dBm) (no IR, radar detection) * 5680 MHz [136] (20.0 dBm) (no IR, radar detection) * 5700 MHz [140] (20.0 dBm) (no IR, radar detection) * 5720 MHz [144] (disabled) * 5745 MHz [149] (disabled) * 5765 MHz [153] (disabled) * 5785 MHz [157] (disabled) * 5805 MHz [161] (disabled) * 5825 MHz [165] (disabled) Supported commands: * new_interface * set_interface * new_key * start_ap * join_ibss * set_pmksa * del_pmksa * flush_pmksa * remain_on_channel * frame * set_wiphy_netns * set_channel * tdls_oper * start_sched_scan * start_p2p_device * connect * disconnect * crit_protocol_start * crit_protocol_stop * update_connect_params software interface modes (can always be added): valid interface combinations:* #{ managed } <= 2, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1,total <= 3, #channels <= 2* #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1,total <= 4, #channels <= 1 Device supports scan flush. Device supports randomizing MAC-addr in sched scans. max # scan plans: 1 max scan plan interval: 508 max scan plan iterations: 0 Supported TX frame types:* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0Supported RX frame types: * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * P2P-device: 0x40 0xd0 Supported extended features: * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records* [ 4WAY_HANDSHAKE_STA_PSK ]: 4-way handshake with PSK in station mode * [ 4WAY_HANDSHAKE_STA_1X ]: 4-way handshake with 802.1X in station mode* [ DFS_OFFLOAD ]: DFS offload
Attachment:
smime.p7s
Description: S/MIME Cryptographic Signature
