On Fri, Dec 2, 2022 at 11:46 AM Marcel Holtmann <marcel@xxxxxxxxxxxx> wrote: > > Hi Dave, > > can you run iwd and set Country=DE (or US) in its main.conf. I think > most distros have a 2.0 package of iwd available. With iwd we have > implemented all the handling and re-scanning to make sure we actually > get to use 6Ghz is available. > > Btw. you can run iwd from its source tree. No need to install it if > You don’t want to mess up your system. Just make sure to disable > wpa_supplicant so it doesn’t interfere. @Marcel, I was able to build iwd from source, but was unable to get it to run due to dbus namespace conflicts. I don't know enough about dbus to debug that further. Running iwd from the archives (v1.26-3), and setting COUNTRY=US in main.conf did not enable the 6e bands. I don't think setting the global region is the issue, as iw reg set US works fine, and results in the following iw reg get. Even before $iw reg set US phy#0 sets itself to the correct region. I think the issue is that the bios, or the firmware blob being loaded by the ax211 that has some bits improperly set that is causing the 6ghz to be disabled by the kernel before userspace ever gets involved. _________________snip_________________ $ sudo iw reg get global country US: DFS-FCC (902 - 904 @ 2), (N/A, 30), (N/A) (904 - 920 @ 16), (N/A, 30), (N/A) (920 - 928 @ 8), (N/A, 30), (N/A) (2400 - 2472 @ 40), (N/A, 30), (N/A) (5150 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW (5250 - 5350 @ 80), (N/A, 24), (0 ms), DFS, AUTO-BW (5470 - 5730 @ 160), (N/A, 24), (0 ms), DFS (5730 - 5850 @ 80), (N/A, 30), (N/A), AUTO-BW (5850 - 5895 @ 40), (N/A, 27), (N/A), NO-OUTDOOR, AUTO-BW, PASSIVE-SCAN (5925 - 7125 @ 320), (N/A, 12), (N/A), NO-OUTDOOR, PASSIVE-SCAN (57240 - 71000 @ 2160), (N/A, 40), (N/A) phy#0 (self-managed) country US: DFS-UNSET (2402 - 2437 @ 40), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS, NO-80MHZ, NO-160MHZ (2422 - 2462 @ 40), (6, 22), (N/A), AUTO-BW, NO-80MHZ, NO-160MHZ (2447 - 2482 @ 40), (6, 22), (N/A), AUTO-BW, NO-HT40PLUS, NO-80MHZ, NO-160MHZ (5170 - 5190 @ 160), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS (5190 - 5210 @ 160), (6, 22), (N/A), AUTO-BW, NO-HT40PLUS (5210 - 5230 @ 160), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS (5230 - 5250 @ 160), (6, 22), (N/A), AUTO-BW, NO-HT40PLUS (5250 - 5270 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, PASSIVE-SCAN (5270 - 5290 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, PASSIVE-SCAN (5290 - 5310 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, PASSIVE-SCAN (5310 - 5330 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, PASSIVE-SCAN (5490 - 5510 @ 240), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, PASSIVE-SCAN (5510 - 5530 @ 240), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, PASSIVE-SCAN (5530 - 5550 @ 240), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, PASSIVE-SCAN (5550 - 5570 @ 240), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, PASSIVE-SCAN (5570 - 5590 @ 240), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, PASSIVE-SCAN (5590 - 5610 @ 240), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, PASSIVE-SCAN (5610 - 5630 @ 240), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, PASSIVE-SCAN (5630 - 5650 @ 240), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, PASSIVE-SCAN (5650 - 5670 @ 80), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-160MHZ, PASSIVE-SCAN (5670 - 5690 @ 80), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-160MHZ, PASSIVE-SCAN (5690 - 5710 @ 80), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-160MHZ, PASSIVE-SCAN (5710 - 5730 @ 80), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-160MHZ, PASSIVE-SCAN (5735 - 5755 @ 80), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS, NO-160MHZ (5755 - 5775 @ 80), (6, 22), (N/A), AUTO-BW, NO-HT40PLUS, NO-160MHZ (5775 - 5795 @ 80), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS, NO-160MHZ (5795 - 5815 @ 80), (6, 22), (N/A), AUTO-BW, NO-HT40PLUS, NO-160MHZ (5815 - 5835 @ 40), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS, NO-80MHZ, NO-160MHZ _________________snip_________________ I wanted to call out the DFS-UNSET setting on phy#0 Dave.
