Search Linux Wireless

[PATCH 21/50] wifi: ath12k: add hal_desc.h

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Kalle Valo <quic_kvalo@xxxxxxxxxxx>

(Patches split into one patch per file for easier review, but the final
commit will be one big patch. See the cover letter for more info.)

Signed-off-by: Kalle Valo <quic_kvalo@xxxxxxxxxxx>
---
 drivers/net/wireless/ath/ath12k/hal_desc.h | 2961 ++++++++++++++++++++++++++++
 1 file changed, 2961 insertions(+)

diff --git a/drivers/net/wireless/ath/ath12k/hal_desc.h b/drivers/net/wireless/ath/ath12k/hal_desc.h
new file mode 100644
index 000000000000..2250ca2d19a3
--- /dev/null
+++ b/drivers/net/wireless/ath/ath12k/hal_desc.h
@@ -0,0 +1,2961 @@
+/* SPDX-License-Identifier: BSD-3-Clause-Clear */
+/*
+ * Copyright (c) 2018-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021-2022 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+#include "core.h"
+
+#ifndef ATH12K_HAL_DESC_H
+#define ATH12K_HAL_DESC_H
+
+#define BUFFER_ADDR_INFO0_ADDR         GENMASK(31, 0)
+
+#define BUFFER_ADDR_INFO1_ADDR         GENMASK(7, 0)
+#define BUFFER_ADDR_INFO1_RET_BUF_MGR  GENMASK(11, 8)
+#define BUFFER_ADDR_INFO1_SW_COOKIE    GENMASK(31, 12)
+
+struct ath12k_buffer_addr {
+	__le32 info0;
+	__le32 info1;
+} __packed;
+
+/* ath12k_buffer_addr
+ *
+ * buffer_addr_31_0
+ *		Address (lower 32 bits) of the MSDU buffer or MSDU_EXTENSION
+ *		descriptor or Link descriptor
+ *
+ * buffer_addr_39_32
+ *		Address (upper 8 bits) of the MSDU buffer or MSDU_EXTENSION
+ *		descriptor or Link descriptor
+ *
+ * return_buffer_manager (RBM)
+ *		Consumer: WBM
+ *		Producer: SW/FW
+ *		Indicates to which buffer manager the buffer or MSDU_EXTENSION
+ *		descriptor or link descriptor that is being pointed to shall be
+ *		returned after the frame has been processed. It is used by WBM
+ *		for routing purposes.
+ *
+ *		Values are defined in enum %HAL_RX_BUF_RBM_
+ *
+ * sw_buffer_cookie
+ *		Cookie field exclusively used by SW. HW ignores the contents,
+ *		accept that it passes the programmed value on to other
+ *		descriptors together with the physical address.
+ *
+ *		Field can be used by SW to for example associate the buffers
+ *		physical address with the virtual address.
+ *
+ *		NOTE1:
+ *		The three most significant bits can have a special meaning
+ *		 in case this struct is embedded in a TX_MPDU_DETAILS STRUCT,
+ *		and field transmit_bw_restriction is set
+ *
+ *		In case of NON punctured transmission:
+ *		Sw_buffer_cookie[19:17] = 3'b000: 20 MHz TX only
+ *		Sw_buffer_cookie[19:17] = 3'b001: 40 MHz TX only
+ *		Sw_buffer_cookie[19:17] = 3'b010: 80 MHz TX only
+ *		Sw_buffer_cookie[19:17] = 3'b011: 160 MHz TX only
+ *		Sw_buffer_cookie[19:17] = 3'b101: 240 MHz TX only
+ *		Sw_buffer_cookie[19:17] = 3'b100: 320 MHz TX only
+ *		Sw_buffer_cookie[19:18] = 2'b11: reserved
+ *
+ *		In case of punctured transmission:
+ *		Sw_buffer_cookie[19:16] = 4'b0000: pattern 0 only
+ *		Sw_buffer_cookie[19:16] = 4'b0001: pattern 1 only
+ *		Sw_buffer_cookie[19:16] = 4'b0010: pattern 2 only
+ *		Sw_buffer_cookie[19:16] = 4'b0011: pattern 3 only
+ *		Sw_buffer_cookie[19:16] = 4'b0100: pattern 4 only
+ *		Sw_buffer_cookie[19:16] = 4'b0101: pattern 5 only
+ *		Sw_buffer_cookie[19:16] = 4'b0110: pattern 6 only
+ *		Sw_buffer_cookie[19:16] = 4'b0111: pattern 7 only
+ *		Sw_buffer_cookie[19:16] = 4'b1000: pattern 8 only
+ *		Sw_buffer_cookie[19:16] = 4'b1001: pattern 9 only
+ *		Sw_buffer_cookie[19:16] = 4'b1010: pattern 10 only
+ *		Sw_buffer_cookie[19:16] = 4'b1011: pattern 11 only
+ *		Sw_buffer_cookie[19:18] = 2'b11: reserved
+ *
+ *		Note: a punctured transmission is indicated by the presence
+ *		 of TLV TX_PUNCTURE_SETUP embedded in the scheduler TLV
+ *
+ *		Sw_buffer_cookie[20:17]: Tid: The TID field in the QoS control
+ *		 field
+ *
+ *		Sw_buffer_cookie[16]: Mpdu_qos_control_valid: This field
+ *		 indicates MPDUs with a QoS control field.
+ *
+ */
+
+enum hal_tlv_tag {
+	HAL_MACTX_CBF_START					= 0 /* 0x0 */,
+	HAL_PHYRX_DATA						= 1 /* 0x1 */,
+	HAL_PHYRX_CBF_DATA_RESP					= 2 /* 0x2 */,
+	HAL_PHYRX_ABORT_REQUEST					= 3 /* 0x3 */,
+	HAL_PHYRX_USER_ABORT_NOTIFICATION			= 4 /* 0x4 */,
+	HAL_MACTX_DATA_RESP					= 5 /* 0x5 */,
+	HAL_MACTX_CBF_DATA					= 6 /* 0x6 */,
+	HAL_MACTX_CBF_DONE					= 7 /* 0x7 */,
+	HAL_PHYRX_LMR_DATA_RESP					= 8 /* 0x8 */,
+	HAL_RXPCU_TO_UCODE_START				= 9 /* 0x9 */,
+	HAL_RXPCU_TO_UCODE_DELIMITER_FOR_FULL_MPDU		= 10 /* 0xa */,
+	HAL_RXPCU_TO_UCODE_FULL_MPDU_DATA			= 11 /* 0xb */,
+	HAL_RXPCU_TO_UCODE_FCS_STATUS				= 12 /* 0xc */,
+	HAL_RXPCU_TO_UCODE_MPDU_DELIMITER			= 13 /* 0xd */,
+	HAL_RXPCU_TO_UCODE_DELIMITER_FOR_MPDU_HEADER		= 14 /* 0xe */,
+	HAL_RXPCU_TO_UCODE_MPDU_HEADER_DATA			= 15 /* 0xf */,
+	HAL_RXPCU_TO_UCODE_END					= 16 /* 0x10 */,
+	HAL_MACRX_CBF_READ_REQUEST				= 32 /* 0x20 */,
+	HAL_MACRX_CBF_DATA_REQUEST				= 33 /* 0x21 */,
+	HAL_MACRXXPECT_NDP_RECEPTION				= 34 /* 0x22 */,
+	HAL_MACRX_FREEZE_CAPTURE_CHANNEL			= 35 /* 0x23 */,
+	HAL_MACRX_NDP_TIMEOUT					= 36 /* 0x24 */,
+	HAL_MACRX_ABORT_ACK					= 37 /* 0x25 */,
+	HAL_MACRX_REQ_IMPLICIT_FB				= 38 /* 0x26 */,
+	HAL_MACRX_CHAIN_MASK					= 39 /* 0x27 */,
+	HAL_MACRX_NAP_USER					= 40 /* 0x28 */,
+	HAL_MACRX_ABORT_REQUEST					= 41 /* 0x29 */,
+	HAL_PHYTX_OTHER_TRANSMIT_INFO16				= 42 /* 0x2a */,
+	HAL_PHYTX_ABORT_ACK					= 43 /* 0x2b */,
+	HAL_PHYTX_ABORT_REQUEST					= 44 /* 0x2c */,
+	HAL_PHYTX_PKT_END					= 45 /* 0x2d */,
+	HAL_PHYTX_PPDU_HEADER_INFO_REQUEST			= 46 /* 0x2e */,
+	HAL_PHYTX_REQUEST_CTRL_INFO				= 47 /* 0x2f */,
+	HAL_PHYTX_DATA_REQUEST					= 48 /* 0x30 */,
+	HAL_PHYTX_BF_CV_LOADING_DONE				= 49 /* 0x31 */,
+	HAL_PHYTX_NAP_ACK					= 50 /* 0x32 */,
+	HAL_PHYTX_NAP_DONE					= 51 /* 0x33 */,
+	HAL_PHYTX_OFF_ACK					= 52 /* 0x34 */,
+	HAL_PHYTX_ON_ACK					= 53 /* 0x35 */,
+	HAL_PHYTX_SYNTH_OFF_ACK					= 54 /* 0x36 */,
+	HAL_PHYTX_DEBUG16					= 55 /* 0x37 */,
+	HAL_MACTX_ABORT_REQUEST					= 56 /* 0x38 */,
+	HAL_MACTX_ABORT_ACK					= 57 /* 0x39 */,
+	HAL_MACTX_PKT_END					= 58 /* 0x3a */,
+	HAL_MACTX_PRE_PHY_DESC					= 59 /* 0x3b */,
+	HAL_MACTX_BF_PARAMS_COMMON				= 60 /* 0x3c */,
+	HAL_MACTX_BF_PARAMS_PER_USER				= 61 /* 0x3d */,
+	HAL_MACTX_PREFETCH_CV					= 62 /* 0x3e */,
+	HAL_MACTX_USER_DESC_COMMON				= 63 /* 0x3f */,
+	HAL_MACTX_USER_DESC_PER_USER				= 64 /* 0x40 */,
+	HAL_XAMPLE_USER_TLV_16					= 65 /* 0x41 */,
+	HAL_XAMPLE_TLV_16					= 66 /* 0x42 */,
+	HAL_MACTX_PHY_OFF					= 67 /* 0x43 */,
+	HAL_MACTX_PHY_ON					= 68 /* 0x44 */,
+	HAL_MACTX_SYNTH_OFF					= 69 /* 0x45 */,
+	HAL_MACTXXPECT_CBF_COMMON				= 70 /* 0x46 */,
+	HAL_MACTXXPECT_CBF_PER_USER				= 71 /* 0x47 */,
+	HAL_MACTX_PHY_DESC					= 72 /* 0x48 */,
+	HAL_MACTX_L_SIG_A					= 73 /* 0x49 */,
+	HAL_MACTX_L_SIG_B					= 74 /* 0x4a */,
+	HAL_MACTX_HT_SIG					= 75 /* 0x4b */,
+	HAL_MACTX_VHT_SIG_A					= 76 /* 0x4c */,
+	HAL_MACTX_VHT_SIG_B_SU20				= 77 /* 0x4d */,
+	HAL_MACTX_VHT_SIG_B_SU40				= 78 /* 0x4e */,
+	HAL_MACTX_VHT_SIG_B_SU80				= 79 /* 0x4f */,
+	HAL_MACTX_VHT_SIG_B_SU160				= 80 /* 0x50 */,
+	HAL_MACTX_VHT_SIG_B_MU20				= 81 /* 0x51 */,
+	HAL_MACTX_VHT_SIG_B_MU40				= 82 /* 0x52 */,
+	HAL_MACTX_VHT_SIG_B_MU80				= 83 /* 0x53 */,
+	HAL_MACTX_VHT_SIG_B_MU160				= 84 /* 0x54 */,
+	HAL_MACTX_SERVICE					= 85 /* 0x55 */,
+	HAL_MACTX_HE_SIG_A_SU					= 86 /* 0x56 */,
+	HAL_MACTX_HE_SIG_A_MU_DL				= 87 /* 0x57 */,
+	HAL_MACTX_HE_SIG_A_MU_UL				= 88 /* 0x58 */,
+	HAL_MACTX_HE_SIG_B1_MU					= 89 /* 0x59 */,
+	HAL_MACTX_HE_SIG_B2_MU					= 90 /* 0x5a */,
+	HAL_MACTX_HE_SIG_B2_OFDMA				= 91 /* 0x5b */,
+	HAL_MACTX_DELETE_CV					= 92 /* 0x5c */,
+	HAL_MACTX_MU_UPLINK_COMMON				= 93 /* 0x5d */,
+	HAL_MACTX_MU_UPLINK_USER_SETUP				= 94 /* 0x5e */,
+	HAL_MACTX_OTHER_TRANSMIT_INFO				= 95 /* 0x5f */,
+	HAL_MACTX_PHY_NAP					= 96 /* 0x60 */,
+	HAL_MACTX_DEBUG						= 97 /* 0x61 */,
+	HAL_PHYRX_ABORT_ACK					= 98 /* 0x62 */,
+	HAL_PHYRX_GENERATED_CBF_DETAILS				= 99 /* 0x63 */,
+	HAL_PHYRX_RSSI_LEGACY					= 100 /* 0x64 */,
+	HAL_PHYRX_RSSI_HT					= 101 /* 0x65 */,
+	HAL_PHYRX_USER_INFO					= 102 /* 0x66 */,
+	HAL_PHYRX_PKT_END					= 103 /* 0x67 */,
+	HAL_PHYRX_DEBUG						= 104 /* 0x68 */,
+	HAL_PHYRX_CBF_TRANSFER_DONE				= 105 /* 0x69 */,
+	HAL_PHYRX_CBF_TRANSFER_ABORT				= 106 /* 0x6a */,
+	HAL_PHYRX_L_SIG_A					= 107 /* 0x6b */,
+	HAL_PHYRX_L_SIG_B					= 108 /* 0x6c */,
+	HAL_PHYRX_HT_SIG					= 109 /* 0x6d */,
+	HAL_PHYRX_VHT_SIG_A					= 110 /* 0x6e */,
+	HAL_PHYRX_VHT_SIG_B_SU20				= 111 /* 0x6f */,
+	HAL_PHYRX_VHT_SIG_B_SU40				= 112 /* 0x70 */,
+	HAL_PHYRX_VHT_SIG_B_SU80				= 113 /* 0x71 */,
+	HAL_PHYRX_VHT_SIG_B_SU160				= 114 /* 0x72 */,
+	HAL_PHYRX_VHT_SIG_B_MU20				= 115 /* 0x73 */,
+	HAL_PHYRX_VHT_SIG_B_MU40				= 116 /* 0x74 */,
+	HAL_PHYRX_VHT_SIG_B_MU80				= 117 /* 0x75 */,
+	HAL_PHYRX_VHT_SIG_B_MU160				= 118 /* 0x76 */,
+	HAL_PHYRX_HE_SIG_A_SU					= 119 /* 0x77 */,
+	HAL_PHYRX_HE_SIG_A_MU_DL				= 120 /* 0x78 */,
+	HAL_PHYRX_HE_SIG_A_MU_UL				= 121 /* 0x79 */,
+	HAL_PHYRX_HE_SIG_B1_MU					= 122 /* 0x7a */,
+	HAL_PHYRX_HE_SIG_B2_MU					= 123 /* 0x7b */,
+	HAL_PHYRX_HE_SIG_B2_OFDMA				= 124 /* 0x7c */,
+	HAL_PHYRX_OTHER_RECEIVE_INFO				= 125 /* 0x7d */,
+	HAL_PHYRX_COMMON_USER_INFO				= 126 /* 0x7e */,
+	HAL_PHYRX_DATA_DONE					= 127 /* 0x7f */,
+	HAL_COEX_TX_REQ						= 128 /* 0x80 */,
+	HAL_DUMMY						= 129 /* 0x81 */,
+	HALXAMPLE_TLV_32_NAME					= 130 /* 0x82 */,
+	HAL_MPDU_LIMIT						= 131 /* 0x83 */,
+	HAL_NA_LENGTH_END					= 132 /* 0x84 */,
+	HAL_OLE_BUF_STATUS					= 133 /* 0x85 */,
+	HAL_PCU_PPDU_SETUP_DONE					= 134 /* 0x86 */,
+	HAL_PCU_PPDU_SETUP_END					= 135 /* 0x87 */,
+	HAL_PCU_PPDU_SETUP_INIT					= 136 /* 0x88 */,
+	HAL_PCU_PPDU_SETUP_START				= 137 /* 0x89 */,
+	HAL_PDG_FES_SETUP					= 138 /* 0x8a */,
+	HAL_PDG_RESPONSE					= 139 /* 0x8b */,
+	HAL_PDG_TX_REQ						= 140 /* 0x8c */,
+	HAL_SCH_WAIT_INSTR					= 141 /* 0x8d */,
+	HAL_TQM_FLOWMPTY_STATUS					= 143 /* 0x8f */,
+	HAL_TQM_FLOW_NOTMPTY_STATUS				= 144 /* 0x90 */,
+	HAL_TQM_GEN_MPDU_LENGTH_LIST				= 145 /* 0x91 */,
+	HAL_TQM_GEN_MPDU_LENGTH_LIST_STATUS			= 146 /* 0x92 */,
+	HAL_TQM_GEN_MPDUS					= 147 /* 0x93 */,
+	HAL_TQM_GEN_MPDUS_STATUS				= 148 /* 0x94 */,
+	HAL_TQM_REMOVE_MPDU					= 149 /* 0x95 */,
+	HAL_TQM_REMOVE_MPDU_STATUS				= 150 /* 0x96 */,
+	HAL_TQM_REMOVE_MSDU					= 151 /* 0x97 */,
+	HAL_TQM_REMOVE_MSDU_STATUS				= 152 /* 0x98 */,
+	HAL_TQM_UPDATE_TX_MPDU_COUNT				= 153 /* 0x99 */,
+	HAL_TQM_WRITE_CMD					= 154 /* 0x9a */,
+	HAL_OFDMA_TRIGGER_DETAILS				= 155 /* 0x9b */,
+	HAL_TX_DATA						= 156 /* 0x9c */,
+	HAL_TX_FES_SETUP					= 157 /* 0x9d */,
+	HAL_RX_PACKET						= 158 /* 0x9e */,
+	HALXPECTED_RESPONSE					= 159 /* 0x9f */,
+	HAL_TX_MPDU_END						= 160 /* 0xa0 */,
+	HAL_TX_MPDU_START					= 161 /* 0xa1 */,
+	HAL_TX_MSDU_END						= 162 /* 0xa2 */,
+	HAL_TX_MSDU_START					= 163 /* 0xa3 */,
+	HAL_TX_SW_MODE_SETUP					= 164 /* 0xa4 */,
+	HAL_TXPCU_BUFFER_STATUS					= 165 /* 0xa5 */,
+	HAL_TXPCU_USER_BUFFER_STATUS				= 166 /* 0xa6 */,
+	HAL_DATA_TO_TIME_CONFIG					= 167 /* 0xa7 */,
+	HALXAMPLE_USER_TLV_32					= 168 /* 0xa8 */,
+	HAL_MPDU_INFO						= 169 /* 0xa9 */,
+	HAL_PDG_USER_SETUP					= 170 /* 0xaa */,
+	HAL_TX_11AH_SETUP					= 171 /* 0xab */,
+	HAL_REO_UPDATE_RX_REO_QUEUE_STATUS			= 172 /* 0xac */,
+	HAL_TX_PEER_ENTRY					= 173 /* 0xad */,
+	HAL_TX_RAW_OR_NATIVE_FRAME_SETUP			= 174 /* 0xae */,
+	HALXAMPLE_USER_TLV_44					= 175 /* 0xaf */,
+	HAL_TX_FLUSH						= 176 /* 0xb0 */,
+	HAL_TX_FLUSH_REQ					= 177 /* 0xb1 */,
+	HAL_TQM_WRITE_CMD_STATUS				= 178 /* 0xb2 */,
+	HAL_TQM_GET_MPDU_QUEUE_STATS				= 179 /* 0xb3 */,
+	HAL_TQM_GET_MSDU_FLOW_STATS				= 180 /* 0xb4 */,
+	HALXAMPLE_USER_CTLV_44					= 181 /* 0xb5 */,
+	HAL_TX_FES_STATUS_START					= 182 /* 0xb6 */,
+	HAL_TX_FES_STATUS_USER_PPDU				= 183 /* 0xb7 */,
+	HAL_TX_FES_STATUS_USER_RESPONSE				= 184 /* 0xb8 */,
+	HAL_TX_FES_STATUS_END					= 185 /* 0xb9 */,
+	HAL_RX_TRIG_INFO					= 186 /* 0xba */,
+	HAL_RXPCU_TX_SETUP_CLEAR				= 187 /* 0xbb */,
+	HAL_RX_FRAME_BITMAP_REQ					= 188 /* 0xbc */,
+	HAL_RX_FRAME_BITMAP_ACK					= 189 /* 0xbd */,
+	HAL_COEX_RX_STATUS					= 190 /* 0xbe */,
+	HAL_RX_START_PARAM					= 191 /* 0xbf */,
+	HAL_RX_PPDU_START					= 192 /* 0xc0 */,
+	HAL_RX_PPDU_END						= 193 /* 0xc1 */,
+	HAL_RX_MPDU_START					= 194 /* 0xc2 */,
+	HAL_RX_MPDU_END						= 195 /* 0xc3 */,
+	HAL_RX_MSDU_START					= 196 /* 0xc4 */,
+	HAL_RX_MSDU_END						= 197 /* 0xc5 */,
+	HAL_RX_ATTENTION					= 198 /* 0xc6 */,
+	HAL_RECEIVED_RESPONSE_INFO				= 199 /* 0xc7 */,
+	HAL_RX_PHY_SLEEP					= 200 /* 0xc8 */,
+	HAL_RX_HEADER						= 201 /* 0xc9 */,
+	HAL_RX_PEER_ENTRY					= 202 /* 0xca */,
+	HAL_RX_FLUSH						= 203 /* 0xcb */,
+	HAL_RX_RESPONSE_REQUIRED_INFO				= 204 /* 0xcc */,
+	HAL_RX_FRAMELESS_BAR_DETAILS				= 205 /* 0xcd */,
+	HAL_TQM_GET_MPDU_QUEUE_STATS_STATUS			= 206 /* 0xce */,
+	HAL_TQM_GET_MSDU_FLOW_STATS_STATUS			= 207 /* 0xcf */,
+	HAL_TX_CBF_INFO						= 208 /* 0xd0 */,
+	HAL_PCU_PPDU_SETUP_USER					= 209 /* 0xd1 */,
+	HAL_RX_MPDU_PCU_START					= 210 /* 0xd2 */,
+	HAL_RX_PM_INFO						= 211 /* 0xd3 */,
+	HAL_RX_USER_PPDU_END					= 212 /* 0xd4 */,
+	HAL_RX_PRE_PPDU_START					= 213 /* 0xd5 */,
+	HAL_RX_PREAMBLE						= 214 /* 0xd6 */,
+	HAL_TX_FES_SETUP_COMPLETE				= 215 /* 0xd7 */,
+	HAL_TX_LAST_MPDU_FETCHED				= 216 /* 0xd8 */,
+	HAL_TXDMA_STOP_REQUEST					= 217 /* 0xd9 */,
+	HAL_RXPCU_SETUP						= 218 /* 0xda */,
+	HAL_RXPCU_USER_SETUP					= 219 /* 0xdb */,
+	HAL_TX_FES_STATUS_ACK_OR_BA				= 220 /* 0xdc */,
+	HAL_TQM_ACKED_MPDU					= 221 /* 0xdd */,
+	HAL_COEX_TX_RESP					= 222 /* 0xde */,
+	HAL_COEX_TX_STATUS					= 223 /* 0xdf */,
+	HAL_MACTX_COEX_PHY_CTRL					= 224 /* 0xe0 */,
+	HAL_COEX_STATUS_BROADCAST				= 225 /* 0xe1 */,
+	HAL_RESPONSE_START_STATUS				= 226 /* 0xe2 */,
+	HAL_RESPONSEND_STATUS					= 227 /* 0xe3 */,
+	HAL_CRYPTO_STATUS					= 228 /* 0xe4 */,
+	HAL_RECEIVED_TRIGGER_INFO				= 229 /* 0xe5 */,
+	HAL_COEX_TX_STOP_CTRL					= 230 /* 0xe6 */,
+	HAL_RX_PPDU_ACK_REPORT					= 231 /* 0xe7 */,
+	HAL_RX_PPDU_NO_ACK_REPORT				= 232 /* 0xe8 */,
+	HAL_SCH_COEX_STATUS					= 233 /* 0xe9 */,
+	HAL_SCHEDULER_COMMAND_STATUS				= 234 /* 0xea */,
+	HAL_SCHEDULER_RX_PPDU_NO_RESPONSE_STATUS		= 235 /* 0xeb */,
+	HAL_TX_FES_STATUS_PROT					= 236 /* 0xec */,
+	HAL_TX_FES_STATUS_START_PPDU				= 237 /* 0xed */,
+	HAL_TX_FES_STATUS_START_PROT				= 238 /* 0xee */,
+	HAL_TXPCU_PHYTX_DEBUG32					= 239 /* 0xef */,
+	HAL_TXPCU_PHYTX_OTHER_TRANSMIT_INFO32			= 240 /* 0xf0 */,
+	HAL_TX_MPDU_COUNT_TRANSFERND				= 241 /* 0xf1 */,
+	HAL_WHO_ANCHOR_OFFSET					= 242 /* 0xf2 */,
+	HAL_WHO_ANCHOR_VALUE					= 243 /* 0xf3 */,
+	HAL_WHO_CCE_INFO					= 244 /* 0xf4 */,
+	HAL_WHO_COMMIT						= 245 /* 0xf5 */,
+	HAL_WHO_COMMIT_DONE					= 246 /* 0xf6 */,
+	HAL_WHO_FLUSH						= 247 /* 0xf7 */,
+	HAL_WHO_L2_LLC						= 248 /* 0xf8 */,
+	HAL_WHO_L2_PAYLOAD					= 249 /* 0xf9 */,
+	HAL_WHO_L3_CHECKSUM					= 250 /* 0xfa */,
+	HAL_WHO_L3_INFO						= 251 /* 0xfb */,
+	HAL_WHO_L4_CHECKSUM					= 252 /* 0xfc */,
+	HAL_WHO_L4_INFO						= 253 /* 0xfd */,
+	HAL_WHO_MSDU						= 254 /* 0xfe */,
+	HAL_WHO_MSDU_MISC					= 255 /* 0xff */,
+	HAL_WHO_PACKET_DATA					= 256 /* 0x100 */,
+	HAL_WHO_PACKET_HDR					= 257 /* 0x101 */,
+	HAL_WHO_PPDU_END					= 258 /* 0x102 */,
+	HAL_WHO_PPDU_START					= 259 /* 0x103 */,
+	HAL_WHO_TSO						= 260 /* 0x104 */,
+	HAL_WHO_WMAC_HEADER_PV0					= 261 /* 0x105 */,
+	HAL_WHO_WMAC_HEADER_PV1					= 262 /* 0x106 */,
+	HAL_WHO_WMAC_IV						= 263 /* 0x107 */,
+	HAL_MPDU_INFO_END					= 264 /* 0x108 */,
+	HAL_MPDU_INFO_BITMAP					= 265 /* 0x109 */,
+	HAL_TX_QUEUE_EXTENSION					= 266 /* 0x10a */,
+	HAL_SCHEDULER_SELFGEN_RESPONSE_STATUS			= 267 /* 0x10b */,
+	HAL_TQM_UPDATE_TX_MPDU_COUNT_STATUS			= 268 /* 0x10c */,
+	HAL_TQM_ACKED_MPDU_STATUS				= 269 /* 0x10d */,
+	HAL_TQM_ADD_MSDU_STATUS					= 270 /* 0x10e */,
+	HAL_TQM_LIST_GEN_DONE					= 271 /* 0x10f */,
+	HAL_WHO_TERMINATE					= 272 /* 0x110 */,
+	HAL_TX_LAST_MPDU_END					= 273 /* 0x111 */,
+	HAL_TX_CV_DATA						= 274 /* 0x112 */,
+	HAL_PPDU_TX_END						= 275 /* 0x113 */,
+	HAL_PROT_TX_END						= 276 /* 0x114 */,
+	HAL_MPDU_INFO_GLOBAL_END				= 277 /* 0x115 */,
+	HAL_TQM_SCH_INSTR_GLOBAL_END				= 278 /* 0x116 */,
+	HAL_RX_PPDU_END_USER_STATS				= 279 /* 0x117 */,
+	HAL_RX_PPDU_END_USER_STATS_EXT				= 280 /* 0x118 */,
+	HAL_REO_GET_QUEUE_STATS					= 281 /* 0x119 */,
+	HAL_REO_FLUSH_QUEUE					= 282 /* 0x11a */,
+	HAL_REO_FLUSH_CACHE					= 283 /* 0x11b */,
+	HAL_REO_UNBLOCK_CACHE					= 284 /* 0x11c */,
+	HAL_REO_GET_QUEUE_STATS_STATUS				= 285 /* 0x11d */,
+	HAL_REO_FLUSH_QUEUE_STATUS				= 286 /* 0x11e */,
+	HAL_REO_FLUSH_CACHE_STATUS				= 287 /* 0x11f */,
+	HAL_REO_UNBLOCK_CACHE_STATUS				= 288 /* 0x120 */,
+	HAL_TQM_FLUSH_CACHE					= 289 /* 0x121 */,
+	HAL_TQM_UNBLOCK_CACHE					= 290 /* 0x122 */,
+	HAL_TQM_FLUSH_CACHE_STATUS				= 291 /* 0x123 */,
+	HAL_TQM_UNBLOCK_CACHE_STATUS				= 292 /* 0x124 */,
+	HAL_RX_PPDU_END_STATUS_DONE				= 293 /* 0x125 */,
+	HAL_RX_STATUS_BUFFER_DONE				= 294 /* 0x126 */,
+	HAL_TX_DATA_SYNC					= 297 /* 0x129 */,
+	HAL_PHYRX_CBF_READ_REQUEST_ACK				= 298 /* 0x12a */,
+	HAL_TQM_GET_MPDU_HEAD_INFO				= 299 /* 0x12b */,
+	HAL_TQM_SYNC_CMD					= 300 /* 0x12c */,
+	HAL_TQM_GET_MPDU_HEAD_INFO_STATUS			= 301 /* 0x12d */,
+	HAL_TQM_SYNC_CMD_STATUS					= 302 /* 0x12e */,
+	HAL_TQM_THRESHOLD_DROP_NOTIFICATION_STATUS		= 303 /* 0x12f */,
+	HAL_TQM_DESCRIPTOR_THRESHOLD_REACHED_STATUS		= 304 /* 0x130 */,
+	HAL_REO_FLUSH_TIMEOUT_LIST				= 305 /* 0x131 */,
+	HAL_REO_FLUSH_TIMEOUT_LIST_STATUS			= 306 /* 0x132 */,
+	HAL_REO_DESCRIPTOR_THRESHOLD_REACHED_STATUS		= 307 /* 0x133 */,
+	HAL_SCHEDULER_RX_SIFS_RESPONSE_TRIGGER_STATUS		= 308 /* 0x134 */,
+	HALXAMPLE_USER_TLV_32_NAME				= 309 /* 0x135 */,
+	HAL_RX_PPDU_START_USER_INFO				= 310 /* 0x136 */,
+	HAL_RX_RING_MASK					= 311 /* 0x137 */,
+	HAL_COEX_MAC_NAP					= 312 /* 0x138 */,
+	HAL_RXPCU_PPDU_END_INFO					= 313 /* 0x139 */,
+	HAL_WHO_MESH_CONTROL					= 314 /* 0x13a */,
+	HAL_PDG_SW_MODE_BW_START				= 315 /* 0x13b */,
+	HAL_PDG_SW_MODE_BW_END					= 316 /* 0x13c */,
+	HAL_PDG_WAIT_FOR_MAC_REQUEST				= 317 /* 0x13d */,
+	HAL_PDG_WAIT_FOR_PHY_REQUEST				= 318 /* 0x13e */,
+	HAL_SCHEDULER_END					= 319 /* 0x13f */,
+	HAL_RX_PPDU_START_DROPPED				= 320 /* 0x140 */,
+	HAL_RX_PPDU_END_DROPPED					= 321 /* 0x141 */,
+	HAL_RX_PPDU_END_STATUS_DONE_DROPPED			= 322 /* 0x142 */,
+	HAL_RX_MPDU_START_DROPPED				= 323 /* 0x143 */,
+	HAL_RX_MSDU_START_DROPPED				= 324 /* 0x144 */,
+	HAL_RX_MSDU_END_DROPPED					= 325 /* 0x145 */,
+	HAL_RX_MPDU_END_DROPPED					= 326 /* 0x146 */,
+	HAL_RX_ATTENTION_DROPPED				= 327 /* 0x147 */,
+	HAL_TXPCU_USER_SETUP					= 328 /* 0x148 */,
+	HAL_RXPCU_USER_SETUP_EXT				= 329 /* 0x149 */,
+	HAL_CMD_PART_0_END					= 330 /* 0x14a */,
+	HAL_MACTX_SYNTH_ON					= 331 /* 0x14b */,
+	HAL_SCH_CRITICAL_TLV_REFERENCE				= 332 /* 0x14c */,
+	HAL_TQM_MPDU_GLOBAL_START				= 333 /* 0x14d */,
+	HALXAMPLE_TLV_32					= 334 /* 0x14e */,
+	HAL_TQM_UPDATE_TX_MSDU_FLOW				= 335 /* 0x14f */,
+	HAL_TQM_UPDATE_TX_MPDU_QUEUE_HEAD			= 336 /* 0x150 */,
+	HAL_TQM_UPDATE_TX_MSDU_FLOW_STATUS			= 337 /* 0x151 */,
+	HAL_TQM_UPDATE_TX_MPDU_QUEUE_HEAD_STATUS		= 338 /* 0x152 */,
+	HAL_REO_UPDATE_RX_REO_QUEUE				= 339 /* 0x153 */,
+	HAL_TQM_MPDU_QUEUEMPTY_STATUS				= 340 /* 0x154 */,
+	HAL_TQM_2_SCH_MPDU_AVAILABLE				= 341 /* 0x155 */,
+	HAL_PDG_TRIG_RESPONSE					= 342 /* 0x156 */,
+	HAL_TRIGGER_RESPONSE_TX_DONE				= 343 /* 0x157 */,
+	HAL_ABORT_FROM_PHYRX_DETAILS				= 344 /* 0x158 */,
+	HAL_SCH_TQM_CMD_WRAPPER					= 345 /* 0x159 */,
+	HAL_MPDUS_AVAILABLE					= 346 /* 0x15a */,
+	HAL_RECEIVED_RESPONSE_INFO_PART2			= 347 /* 0x15b */,
+	HAL_PHYRX_TX_START_TIMING				= 348 /* 0x15c */,
+	HAL_TXPCU_PREAMBLE_DONE					= 349 /* 0x15d */,
+	HAL_NDP_PREAMBLE_DONE					= 350 /* 0x15e */,
+	HAL_SCH_TQM_CMD_WRAPPER_RBO_DROP			= 351 /* 0x15f */,
+	HAL_SCH_TQM_CMD_WRAPPER_CONT_DROP			= 352 /* 0x160 */,
+	HAL_MACTX_CLEAR_PREV_TX_INFO				= 353 /* 0x161 */,
+	HAL_TX_PUNCTURE_SETUP					= 354 /* 0x162 */,
+	HAL_R2R_STATUS_END					= 355 /* 0x163 */,
+	HAL_MACTX_PREFETCH_CV_COMMON				= 356 /* 0x164 */,
+	HAL_END_OF_FLUSH_MARKER					= 357 /* 0x165 */,
+	HAL_MACTX_MU_UPLINK_COMMON_PUNC				= 358 /* 0x166 */,
+	HAL_MACTX_MU_UPLINK_USER_SETUP_PUNC			= 359 /* 0x167 */,
+	HAL_RECEIVED_RESPONSE_USER_7_0				= 360 /* 0x168 */,
+	HAL_RECEIVED_RESPONSE_USER_15_8				= 361 /* 0x169 */,
+	HAL_RECEIVED_RESPONSE_USER_23_16			= 362 /* 0x16a */,
+	HAL_RECEIVED_RESPONSE_USER_31_24			= 363 /* 0x16b */,
+	HAL_RECEIVED_RESPONSE_USER_36_32			= 364 /* 0x16c */,
+	HAL_TX_LOOPBACK_SETUP					= 365 /* 0x16d */,
+	HAL_PHYRX_OTHER_RECEIVE_INFO_RU_DETAILS			= 366 /* 0x16e */,
+	HAL_SCH_WAIT_INSTR_TX_PATH				= 367 /* 0x16f */,
+	HAL_MACTX_OTHER_TRANSMIT_INFO_TX2TX			= 368 /* 0x170 */,
+	HAL_MACTX_OTHER_TRANSMIT_INFOMUPHY_SETUP		= 369 /* 0x171 */,
+	HAL_PHYRX_OTHER_RECEIVE_INFOVM_DETAILS			= 370 /* 0x172 */,
+	HAL_TX_WUR_DATA						= 371 /* 0x173 */,
+	HAL_RX_PPDU_END_START					= 372 /* 0x174 */,
+	HAL_RX_PPDU_END_MIDDLE					= 373 /* 0x175 */,
+	HAL_RX_PPDU_END_LAST					= 374 /* 0x176 */,
+	HAL_MACTX_BACKOFF_BASED_TRANSMISSION			= 375 /* 0x177 */,
+	HAL_MACTX_OTHER_TRANSMIT_INFO_DL_OFDMA_TX		= 376 /* 0x178 */,
+	HAL_SRP_INFO						= 377 /* 0x179 */,
+	HAL_OBSS_SR_INFO					= 378 /* 0x17a */,
+	HAL_SCHEDULER_SW_MSG_STATUS				= 379 /* 0x17b */,
+	HAL_HWSCH_RXPCU_MAC_INFO_ANNOUNCEMENT			= 380 /* 0x17c */,
+	HAL_RXPCU_SETUP_COMPLETE				= 381 /* 0x17d */,
+	HAL_SNOOP_PPDU_START					= 382 /* 0x17e */,
+	HAL_SNOOP_MPDU_USR_DBG_INFO				= 383 /* 0x17f */,
+	HAL_SNOOP_MSDU_USR_DBG_INFO				= 384 /* 0x180 */,
+	HAL_SNOOP_MSDU_USR_DATA					= 385 /* 0x181 */,
+	HAL_SNOOP_MPDU_USR_STAT_INFO				= 386 /* 0x182 */,
+	HAL_SNOOP_PPDU_END					= 387 /* 0x183 */,
+	HAL_SNOOP_SPARE						= 388 /* 0x184 */,
+	HAL_PHYRX_OTHER_RECEIVE_INFO_MU_RSSI_COMMON		= 390 /* 0x186 */,
+	HAL_PHYRX_OTHER_RECEIVE_INFO_MU_RSSI_USER		= 391 /* 0x187 */,
+	HAL_MACTX_OTHER_TRANSMIT_INFO_SCH_DETAILS		= 392 /* 0x188 */,
+	HAL_PHYRX_OTHER_RECEIVE_INFO_108PVM_DETAILS		= 393 /* 0x189 */,
+	HAL_SCH_TLV_WRAPPER					= 394 /* 0x18a */,
+	HAL_SCHEDULER_STATUS_WRAPPER				= 395 /* 0x18b */,
+	HAL_MPDU_INFO_6X					= 396 /* 0x18c */,
+	HAL_MACTX_11AZ_USER_DESC_PER_USER			= 397 /* 0x18d */,
+	HAL_MACTX_U_SIGHT_SU_MU					= 398 /* 0x18e */,
+	HAL_MACTX_U_SIGHT_TB					= 399 /* 0x18f */,
+	HAL_PHYRX_U_SIGHT_SU_MU					= 403 /* 0x193 */,
+	HAL_PHYRX_U_SIGHT_TB					= 404 /* 0x194 */,
+	HAL_MACRX_LMR_READ_REQUEST				= 408 /* 0x198 */,
+	HAL_MACRX_LMR_DATA_REQUEST				= 409 /* 0x199 */,
+	HAL_PHYRX_LMR_TRANSFER_DONE				= 410 /* 0x19a */,
+	HAL_PHYRX_LMR_TRANSFER_ABORT				= 411 /* 0x19b */,
+	HAL_PHYRX_LMR_READ_REQUEST_ACK				= 412 /* 0x19c */,
+	HAL_MACRX_SECURE_LTF_SEQ_PTR				= 413 /* 0x19d */,
+	HAL_PHYRX_USER_INFO_MU_UL				= 414 /* 0x19e */,
+	HAL_MPDU_QUEUE_OVERVIEW					= 415 /* 0x19f */,
+	HAL_SCHEDULER_NAV_INFO					= 416 /* 0x1a0 */,
+	HAL_LMR_PEER_ENTRY					= 418 /* 0x1a2 */,
+	HAL_LMR_MPDU_START					= 419 /* 0x1a3 */,
+	HAL_LMR_DATA						= 420 /* 0x1a4 */,
+	HAL_LMR_MPDU_END					= 421 /* 0x1a5 */,
+	HAL_REO_GET_QUEUE_1K_STATS_STATUS			= 422 /* 0x1a6 */,
+	HAL_RX_FRAME_1K_BITMAP_ACK				= 423 /* 0x1a7 */,
+	HAL_TX_FES_STATUS_1K_BA					= 424 /* 0x1a8 */,
+	HAL_TQM_ACKED_1K_MPDU					= 425 /* 0x1a9 */,
+	HAL_MACRX_INBSS_OBSS_IND				= 426 /* 0x1aa */,
+	HAL_PHYRX_LOCATION					= 427 /* 0x1ab */,
+	HAL_MLO_TX_NOTIFICATION_SU				= 428 /* 0x1ac */,
+	HAL_MLO_TX_NOTIFICATION_MU				= 429 /* 0x1ad */,
+	HAL_MLO_TX_REQ_SU					= 430 /* 0x1ae */,
+	HAL_MLO_TX_REQ_MU					= 431 /* 0x1af */,
+	HAL_MLO_TX_RESP						= 432 /* 0x1b0 */,
+	HAL_MLO_RX_NOTIFICATION					= 433 /* 0x1b1 */,
+	HAL_MLO_BKOFF_TRUNC_REQ					= 434 /* 0x1b2 */,
+	HAL_MLO_TBTT_NOTIFICATION				= 435 /* 0x1b3 */,
+	HAL_MLO_MESSAGE						= 436 /* 0x1b4 */,
+	HAL_MLO_TS_SYNC_MSG					= 437 /* 0x1b5 */,
+	HAL_MLO_FES_SETUP					= 438 /* 0x1b6 */,
+	HAL_MLO_PDG_FES_SETUP_SU				= 439 /* 0x1b7 */,
+	HAL_MLO_PDG_FES_SETUP_MU				= 440 /* 0x1b8 */,
+	HAL_MPDU_INFO_1K_BITMAP					= 441 /* 0x1b9 */,
+	HAL_MON_BUF_ADDR					= 442 /* 0x1ba */,
+	HAL_TX_FRAG_STATE					= 443 /* 0x1bb */,
+	HAL_MACTXHT_SIG_USR_OFDMA				= 446 /* 0x1be */,
+	HAL_PHYRXHT_SIG_CMN_PUNC				= 448 /* 0x1c0 */,
+	HAL_PHYRXHT_SIG_CMN_OFDMA				= 450 /* 0x1c2 */,
+	HAL_PHYRXHT_SIG_USR_OFDMA				= 454 /* 0x1c6 */,
+	HAL_PHYRX_PKT_END_PART1					= 456 /* 0x1c8 */,
+	HAL_MACTXXPECT_NDP_RECEPTION				= 457 /* 0x1c9 */,
+	HAL_MACTX_SECURE_LTF_SEQ_PTR				= 458 /* 0x1ca */,
+	HAL_MLO_PDG_BKOFF_TRUNC_NOTIFY				= 460 /* 0x1cc */,
+	HAL_PHYRX_11AZ_INTEGRITY_DATA				= 461 /* 0x1cd */,
+	HAL_PHYTX_LOCATION					= 462 /* 0x1ce */,
+	HAL_PHYTX_11AZ_INTEGRITY_DATA				= 463 /* 0x1cf */,
+	HAL_MACTXHT_SIG_USR_SU					= 466 /* 0x1d2 */,
+	HAL_MACTXHT_SIG_USR_MU_MIMO				= 467 /* 0x1d3 */,
+	HAL_PHYRXHT_SIG_USR_SU					= 468 /* 0x1d4 */,
+	HAL_PHYRXHT_SIG_USR_MU_MIMO				= 469 /* 0x1d5 */,
+	HAL_PHYRX_GENERIC_U_SIG					= 470 /* 0x1d6 */,
+	HAL_PHYRX_GENERICHT_SIG					= 471 /* 0x1d7 */,
+	HAL_OVERWRITE_RESP_START				= 472 /* 0x1d8 */,
+	HAL_OVERWRITE_RESP_PREAMBLE_INFO			= 473 /* 0x1d9 */,
+	HAL_OVERWRITE_RESP_FRAME_INFO				= 474 /* 0x1da */,
+	HAL_OVERWRITE_RESP_END					= 475 /* 0x1db */,
+	HAL_RXPCUARLY_RX_INDICATION				= 476 /* 0x1dc */,
+	HAL_MON_DROP						= 477 /* 0x1dd */,
+	HAL_MACRX_MU_UPLINK_COMMON_SNIFF			= 478 /* 0x1de */,
+	HAL_MACRX_MU_UPLINK_USER_SETUP_SNIFF			= 479 /* 0x1df */,
+	HAL_MACRX_MU_UPLINK_USER_SEL_SNIFF			= 480 /* 0x1e0 */,
+	HAL_MACRX_MU_UPLINK_FCS_STATUS_SNIFF			= 481 /* 0x1e1 */,
+	HAL_MACTX_PREFETCH_CV_DMA				= 482 /* 0x1e2 */,
+	HAL_MACTX_PREFETCH_CV_PER_USER				= 483 /* 0x1e3 */,
+	HAL_PHYRX_OTHER_RECEIVE_INFO_ALL_SIGB_DETAILS		= 484 /* 0x1e4 */,
+	HAL_MACTX_BF_PARAMS_UPDATE_COMMON			= 485 /* 0x1e5 */,
+	HAL_MACTX_BF_PARAMS_UPDATE_PER_USER			= 486 /* 0x1e6 */,
+	HAL_RANGING_USER_DETAILS				= 487 /* 0x1e7 */,
+	HAL_PHYTX_CV_CORR_STATUS				= 488 /* 0x1e8 */,
+	HAL_PHYTX_CV_CORR_COMMON				= 489 /* 0x1e9 */,
+	HAL_PHYTX_CV_CORR_USER					= 490 /* 0x1ea */,
+	HAL_MACTX_CV_CORR_COMMON				= 491 /* 0x1eb */,
+	HAL_MACTX_CV_CORR_MAC_INFO_GROUP			= 492 /* 0x1ec */,
+	HAL_BW_PUNCTUREVAL_WRAPPER				= 493 /* 0x1ed */,
+	HAL_MACTX_RX_NOTIFICATION_FOR_PHY			= 494 /* 0x1ee */,
+	HAL_MACTX_TX_NOTIFICATION_FOR_PHY			= 495 /* 0x1ef */,
+	HAL_MACTX_MU_UPLINK_COMMON_PER_BW			= 496 /* 0x1f0 */,
+	HAL_MACTX_MU_UPLINK_USER_SETUP_PER_BW			= 497 /* 0x1f1 */,
+	HAL_RX_PPDU_END_USER_STATS_EXT2				= 498 /* 0x1f2 */,
+	HAL_FW2SW_MON						= 499 /* 0x1f3 */,
+	HAL_WSI_DIRECT_MESSAGE					= 500 /* 0x1f4 */,
+	HAL_MACTXMLSR_PRE_SWITCH				= 501 /* 0x1f5 */,
+	HAL_MACTXMLSR_SWITCH					= 502 /* 0x1f6 */,
+	HAL_MACTXMLSR_SWITCH_BACK				= 503 /* 0x1f7 */,
+	HAL_PHYTXMLSR_SWITCH_ACK				= 504 /* 0x1f8 */,
+	HAL_PHYTXMLSR_SWITCH_BACK_ACK				= 505 /* 0x1f9 */,
+	HAL_SPARE_REUSE_TAG_0					= 506 /* 0x1fa */,
+	HAL_SPARE_REUSE_TAG_1					= 507 /* 0x1fb */,
+	HAL_SPARE_REUSE_TAG_2					= 508 /* 0x1fc */,
+	HAL_SPARE_REUSE_TAG_3					= 509 /* 0x1fd */,
+	/* FIXME: Assign correct value for HAL_TCL_DATA_CMD */
+	HAL_TCL_DATA_CMD					= 510,
+	HAL_TLV_BASE						= 511 /* 0x1ff */,
+};
+
+#define HAL_TLV_HDR_TAG		GENMASK(9, 1)
+#define HAL_TLV_HDR_LEN		GENMASK(25, 10)
+#define HAL_TLV_USR_ID          GENMASK(31, 26)
+
+#define HAL_TLV_ALIGN	4
+
+struct hal_tlv_hdr {
+	__le32 tl;
+	u8 value[];
+} __packed;
+
+#define HAL_TLV_64_HDR_TAG		GENMASK(9, 1)
+#define HAL_TLV_64_HDR_LEN		GENMASK(21, 10)
+
+struct hal_tlv_64_hdr {
+	u64 tl;
+	u8 value[];
+} __packed;
+
+#define RX_MPDU_DESC_INFO0_MSDU_COUNT		GENMASK(7, 0)
+#define RX_MPDU_DESC_INFO0_FRAG_FLAG		BIT(8)
+#define RX_MPDU_DESC_INFO0_MPDU_RETRY		BIT(9)
+#define RX_MPDU_DESC_INFO0_AMPDU_FLAG		BIT(10)
+#define RX_MPDU_DESC_INFO0_BAR_FRAME		BIT(11)
+#define RX_MPDU_DESC_INFO0_VALID_PN		BIT(12)
+#define RX_MPDU_DESC_INFO0_RAW_MPDU		BIT(13)
+#define RX_MPDU_DESC_INFO0_MORE_FRAG_FLAG	BIT(14)
+#define RX_MPDU_DESC_INFO0_SRC_INFO		GENMASK(26, 15)
+#define RX_MPDU_DESC_INFO0_MPDU_QOS_CTRL_VALID	BIT(27)
+#define RX_MPDU_DESC_INFO0_TID			GENMASK(31, 28)
+
+/* TODO revisit after meta data is concluded */
+#define RX_MPDU_DESC_META_DATA_PEER_ID		GENMASK(15, 0)
+
+struct rx_mpdu_desc {
+	__le32 info0; /* %RX_MPDU_DESC_INFO */
+	__le32 peer_meta_data;
+} __packed;
+
+/* rx_mpdu_desc
+ *		Producer: RXDMA
+ *		Consumer: REO/SW/FW
+ *
+ * msdu_count
+ *		The number of MSDUs within the MPDU
+ *
+ * fragment_flag
+ *		When set, this MPDU is a fragment and REO should forward this
+ *		fragment MPDU to the REO destination ring without any reorder
+ *		checks, pn checks or bitmap update. This implies that REO is
+ *		forwarding the pointer to the MSDU link descriptor.
+ *
+ * mpdu_retry_bit
+ *		The retry bit setting from the MPDU header of the received frame
+ *
+ * ampdu_flag
+ *		Indicates the MPDU was received as part of an A-MPDU.
+ *
+ * bar_frame
+ *		Indicates the received frame is a BAR frame. After processing,
+ *		this frame shall be pushed to SW or deleted.
+ *
+ * valid_pn
+ *		When not set, REO will not perform a PN sequence number check.
+ *
+ * raw_mpdu
+ *		Field only valid when first_msdu_in_mpdu_flag is set. Indicates
+ *		the contents in the MSDU buffer contains a 'RAW' MPDU. This
+ *		'RAW' MPDU might be spread out over multiple MSDU buffers.
+ *
+ * more_fragment_flag
+ *		The More Fragment bit setting from the MPDU header of the
+ *		received frame
+ *
+ * src_info
+ *		Source (Virtual) device/interface info associated with this peer.
+ *		This field gets passed on by REO to PPE in the EDMA descriptor.
+ *
+ * mpdu_qos_control_valid
+ *		When set, the MPDU has a QoS control field
+ *
+ * tid
+ *		Field only valid when mpdu_qos_control_valid is set
+ */
+
+enum hal_rx_msdu_desc_reo_dest_ind {
+	HAL_RX_MSDU_DESC_REO_DEST_IND_TCL,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_SW1,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_SW2,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_SW3,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_SW4,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_RELEASE,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_FW,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_SW5,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_SW6,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_SW7,
+	HAL_RX_MSDU_DESC_REO_DEST_IND_SW8,
+};
+
+#define RX_MSDU_DESC_INFO0_FIRST_MSDU_IN_MPDU	BIT(0)
+#define RX_MSDU_DESC_INFO0_LAST_MSDU_IN_MPDU	BIT(1)
+#define RX_MSDU_DESC_INFO0_MSDU_CONTINUATION	BIT(2)
+#define RX_MSDU_DESC_INFO0_MSDU_LENGTH		GENMASK(16, 3)
+#define RX_MSDU_DESC_INFO0_MSDU_DROP		BIT(17)
+#define RX_MSDU_DESC_INFO0_VALID_SA		BIT(18)
+#define RX_MSDU_DESC_INFO0_VALID_DA		BIT(19)
+#define RX_MSDU_DESC_INFO0_DA_MCBC		BIT(20)
+#define RX_MSDU_DESC_INFO0_L3_HDR_PAD_MSB	BIT(21)
+#define RX_MSDU_DESC_INFO0_TCP_UDP_CHKSUM_FAIL	BIT(22)
+#define RX_MSDU_DESC_INFO0_IP_CHKSUM_FAIL	BIT(23)
+#define RX_MSDU_DESC_INFO0_FROM_DS		BIT(24)
+#define RX_MSDU_DESC_INFO0_TO_DS		BIT(25)
+#define RX_MSDU_DESC_INFO0_INTRA_BSS		BIT(26)
+#define RX_MSDU_DESC_INFO0_DST_CHIP_ID		GENMASK(28, 27)
+#define RX_MSDU_DESC_INFO0_DECAP_FORMAT		GENMASK(30, 29)
+
+#define HAL_RX_MSDU_PKT_LENGTH_GET(val)		\
+	(u32_get_bits((val), RX_MSDU_DESC_INFO0_MSDU_LENGTH))
+
+struct rx_msdu_desc {
+	__le32 info0;
+} __packed;
+
+/* rx_msdu_desc
+ *
+ * first_msdu_in_mpdu
+ *		Indicates first msdu in mpdu.
+ *
+ * last_msdu_in_mpdu
+ *		Indicates last msdu in mpdu. This flag can be true only when
+ *		'Msdu_continuation' set to 0. This implies that when an msdu
+ *		is spread out over multiple buffers and thus msdu_continuation
+ *		is set, only for the very last buffer of the msdu, can the
+ *		'last_msdu_in_mpdu' be set.
+ *
+ *		When both first_msdu_in_mpdu and last_msdu_in_mpdu are set,
+ *		the MPDU that this MSDU belongs to only contains a single MSDU.
+ *
+ * msdu_continuation
+ *		When set, this MSDU buffer was not able to hold the entire MSDU.
+ *		The next buffer will therefor contain additional information
+ *		related to this MSDU.
+ *
+ * msdu_length
+ *		Field is only valid in combination with the 'first_msdu_in_mpdu'
+ *		being set. Full MSDU length in bytes after decapsulation. This
+ *		field is still valid for MPDU frames without A-MSDU. It still
+ *		represents MSDU length after decapsulation Or in case of RAW
+ *		MPDUs, it indicates the length of the entire MPDU (without FCS
+ *		field).
+ *
+ * msdu_drop
+ *		Indicates that REO shall drop this MSDU and not forward it to
+ *		any other ring.
+ *
+ * valid_sa
+ *		Indicates OLE found a valid SA entry for this MSDU.
+ *
+ * valid_da
+ *		When set, OLE found a valid DA entry for this MSDU.
+ *
+ * da_mcbc
+ *		Field Only valid if valid_da is set. Indicates the DA address
+ *		is a Multicast or Broadcast address for this MSDU.
+ *
+ * l3_header_padding_msb
+ *		Passed on from 'RX_MSDU_END' TLV (only the MSB is reported as
+ *		the LSB is always zero). Number of bytes padded to make sure
+ *		that the L3 header will always start of a Dword boundary
+ *
+ * tcp_udp_checksum_fail
+ *		Passed on from 'RX_ATTENTION' TLV
+ *		Indicates that the computed checksum did not match the checksum
+ *		in the TCP/UDP header.
+ *
+ * ip_checksum_fail
+ *		Passed on from 'RX_ATTENTION' TLV
+ *		Indicates that the computed checksum did not match the checksum
+ *		in the IP header.
+ *
+ * from_DS
+ *		Set if the 'from DS' bit is set in the frame control.
+ *
+ * to_DS
+ *		Set if the 'to DS' bit is set in the frame control.
+ *
+ * intra_bss
+ *		This packet needs intra-BSS routing by SW as the 'vdev_id'
+ *		for the destination is the same as the 'vdev_id' that this
+ *		MSDU was got in.
+ *
+ * dest_chip_id
+ *		If intra_bss is set, copied by RXOLE/RXDMA from 'ADDR_SEARCH_ENTRY'
+ *		to support intra-BSS routing with multi-chip multi-link operation.
+ *		This indicates into which chip's TCL the packet should be queued.
+ *
+ * decap_format
+ *		Indicates the format after decapsulation:
+ */
+
+#define RX_MSDU_EXT_DESC_INFO0_REO_DEST_IND	GENMASK(4, 0)
+#define RX_MSDU_EXT_DESC_INFO0_SERVICE_CODE	GENMASK(13, 5)
+#define RX_MSDU_EXT_DESC_INFO0_PRIORITY_VALID	BIT(14)
+#define RX_MSDU_EXT_DESC_INFO0_DATA_OFFSET	GENMASK(26, 15)
+#define RX_MSDU_EXT_DESC_INFO0_SRC_LINK_ID	GENMASK(29, 27)
+
+struct rx_msdu_ext_desc {
+	__le32 info0;
+} __packed;
+
+/* rx_msdu_ext_desc
+ *
+ * reo_destination_indication
+ *		The ID of the REO exit ring where the MSDU frame shall push
+ *		after (MPDU level) reordering has finished.
+ *
+ * service_code
+ *		Opaque service code between PPE and Wi-Fi
+ *
+ * priority_valid
+ *
+ * data_offset
+ *		The offset to Rx packet data within the buffer (including
+ *		Rx DMA offset programming and L3 header padding inserted
+ *		by Rx OLE).
+ *
+ * src_link_id
+ *		Set to the link ID of the PMAC that received the frame
+ */
+
+enum hal_reo_dest_ring_buffer_type {
+	HAL_REO_DEST_RING_BUFFER_TYPE_MSDU,
+	HAL_REO_DEST_RING_BUFFER_TYPE_LINK_DESC,
+};
+
+enum hal_reo_dest_ring_push_reason {
+	HAL_REO_DEST_RING_PUSH_REASON_ERR_DETECTED,
+	HAL_REO_DEST_RING_PUSH_REASON_ROUTING_INSTRUCTION,
+};
+
+enum hal_reo_dest_ring_error_code {
+	HAL_REO_DEST_RING_ERROR_CODE_DESC_ADDR_ZERO,
+	HAL_REO_DEST_RING_ERROR_CODE_DESC_INVALID,
+	HAL_REO_DEST_RING_ERROR_CODE_AMPDU_IN_NON_BA,
+	HAL_REO_DEST_RING_ERROR_CODE_NON_BA_DUPLICATE,
+	HAL_REO_DEST_RING_ERROR_CODE_BA_DUPLICATE,
+	HAL_REO_DEST_RING_ERROR_CODE_FRAME_2K_JUMP,
+	HAL_REO_DEST_RING_ERROR_CODE_BAR_2K_JUMP,
+	HAL_REO_DEST_RING_ERROR_CODE_FRAME_OOR,
+	HAL_REO_DEST_RING_ERROR_CODE_BAR_OOR,
+	HAL_REO_DEST_RING_ERROR_CODE_NO_BA_SESSION,
+	HAL_REO_DEST_RING_ERROR_CODE_FRAME_SN_EQUALS_SSN,
+	HAL_REO_DEST_RING_ERROR_CODE_PN_CHECK_FAILED,
+	HAL_REO_DEST_RING_ERROR_CODE_2K_ERR_FLAG_SET,
+	HAL_REO_DEST_RING_ERROR_CODE_PN_ERR_FLAG_SET,
+	HAL_REO_DEST_RING_ERROR_CODE_DESC_BLOCKED,
+	HAL_REO_DEST_RING_ERROR_CODE_MAX,
+};
+
+#define HAL_REO_DEST_RING_INFO0_BUFFER_TYPE		BIT(0)
+#define HAL_REO_DEST_RING_INFO0_PUSH_REASON		GENMASK(2, 1)
+#define HAL_REO_DEST_RING_INFO0_ERROR_CODE		GENMASK(7, 3)
+#define HAL_REO_DEST_RING_INFO0_MSDU_DATA_SIZE		GENMASK(11, 8)
+#define HAL_REO_DEST_RING_INFO0_SW_EXCEPTION		BIT(12)
+#define HAL_REO_DEST_RING_INFO0_SRC_LINK_ID		GENMASK(15, 13)
+#define HAL_REO_DEST_RING_INFO0_SIGNATURE		GENMASK(19, 16)
+#define HAL_REO_DEST_RING_INFO0_RING_ID			GENMASK(27, 20)
+#define HAL_REO_DEST_RING_INFO0_LOOPING_COUNT		GENMASK(31, 28)
+
+struct hal_reo_dest_ring {
+	struct ath12k_buffer_addr buf_addr_info;
+	struct rx_mpdu_desc rx_mpdu_info;
+	struct rx_msdu_desc rx_msdu_info;
+	__le32 buf_va_lo;
+	__le32 buf_va_hi;
+	__le32 info0; /* %HAL_REO_DEST_RING_INFO0_ */
+} __packed;
+
+/* hal_reo_dest_ring
+ *
+ *		Producer: RXDMA
+ *		Consumer: REO/SW/FW
+ *
+ * buf_addr_info
+ *		Details of the physical address of a buffer or MSDU
+ *		link descriptor.
+ *
+ * rx_mpdu_info
+ *		General information related to the MPDU that is passed
+ *		on from REO entrance ring to the REO destination ring.
+ *
+ * rx_msdu_info
+ *		General information related to the MSDU that is passed
+ *		on from RXDMA all the way to the REO destination ring.
+ *
+ * buf_va_lo
+ *		Field only valid if Reo_dest_buffer_type is set to MSDU_buf_address
+ *		Lower 32 bits of the 64-bit virtual address corresponding
+ *		to Buf_or_link_desc_addr_info
+ *
+ * buf_va_hi
+ *		Address (upper 32 bits) of the REO queue descriptor.
+ *		Upper 32 bits of the 64-bit virtual address corresponding
+ *		to Buf_or_link_desc_addr_info
+ *
+ * buffer_type
+ *		Indicates the type of address provided in the buf_addr_info.
+ *		Values are defined in enum %HAL_REO_DEST_RING_BUFFER_TYPE_.
+ *
+ * push_reason
+ *		Reason for pushing this frame to this exit ring. Values are
+ *		defined in enum %HAL_REO_DEST_RING_PUSH_REASON_.
+ *
+ * error_code
+ *		Valid only when 'push_reason' is set. All error codes are
+ *		defined in enum %HAL_REO_DEST_RING_ERROR_CODE_.
+ *
+ * captured_msdu_data_size
+ *		The number of following REO_DESTINATION STRUCTs that have
+ *		been replaced with msdu_data extracted from the msdu_buffer
+ *		and copied into the ring for easy FW/SW access.
+ *
+ * sw_exception
+ *		This field has the same setting as the SW_exception field
+ *		in the corresponding REO_entrance_ring descriptor.
+ *		When set, the REO entrance descriptor is generated by FW,
+ *		and the MPDU was processed in the following way:
+ *		- NO re-order function is needed.
+ *		- MPDU delinking is determined by the setting of Entrance
+ *		  ring field: SW_excection_mpdu_delink
+ *		- Destination ring selection is based on the setting of
+ *		  the Entrance ring field SW_exception_destination _ring_valid
+ *
+ * src_link_id
+ *		Set to the link ID of the PMAC that received the frame
+ *
+ * signature
+ *		Set to value 0x8 when msdu capture mode is enabled for this ring
+ *
+ * ring_id
+ *		The buffer pointer ring id.
+ *		0 - Idle ring
+ *		1 - N refers to other rings.
+ *
+ * looping_count
+ *		Indicates the number of times the producer of entries into
+ *		this ring has looped around the ring.
+ */
+
+#define HAL_REO_TO_PPE_RING_INFO0_DATA_LENGTH	GENMASK(15, 0)
+#define HAL_REO_TO_PPE_RING_INFO0_DATA_OFFSET	GENMASK(23, 16)
+#define HAL_REO_TO_PPE_RING_INFO0_POOL_ID	GENMASK(28, 24)
+#define HAL_REO_TO_PPE_RING_INFO0_PREHEADER	BIT(29)
+#define HAL_REO_TO_PPE_RING_INFO0_TSO_EN	BIT(30)
+#define HAL_REO_TO_PPE_RING_INFO0_MORE	BIT(31)
+
+struct hal_reo_to_ppe_ring {
+	__le32 buffer_addr;
+	__le32 info0; /* %HAL_REO_TO_PPE_RING_INFO0_ */
+} __packed;
+
+/* hal_reo_to_ppe_ring
+ *
+ *		Producer: REO
+ *		Consumer: PPE
+ *
+ * buf_addr_info
+ *		Details of the physical address of a buffer or MSDU
+ *		link descriptor.
+ *
+ * data_length
+ *		Length of valid data in bytes
+ *
+ * data_offset
+ *		Offset to the data from buffer pointer. Can be used to
+ *		strip header in the data for tunnel termination etc.
+ *
+ * pool_id
+ *		REO has global configuration register for this field.
+ *		It may have several free buffer pools, each
+ *		RX-Descriptor ring can fetch free buffer from specific
+ *		buffer pool; pool id will indicate which pool the buffer
+ *		will be released to; POOL_ID Zero returned to SW
+ *
+ * preheader
+ *		Disabled: 0 (Default)
+ *		Enabled: 1
+ *
+ * tso_en
+ *		Disabled: 0 (Default)
+ *		Enabled: 1
+ *
+ * more
+ *		More Segments followed
+ */
+
+enum hal_reo_entr_rxdma_push_reason {
+	HAL_REO_ENTR_RING_RXDMA_PUSH_REASON_ERR_DETECTED,
+	HAL_REO_ENTR_RING_RXDMA_PUSH_REASON_ROUTING_INSTRUCTION,
+	HAL_REO_ENTR_RING_RXDMA_PUSH_REASON_RX_FLUSH,
+};
+
+enum hal_reo_entr_rxdma_ecode {
+	HAL_REO_ENTR_RING_RXDMA_ECODE_OVERFLOW_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_MPDU_LEN_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_FCS_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_DECRYPT_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_TKIP_MIC_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_UNECRYPTED_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_MSDU_LEN_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_MSDU_LIMIT_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_WIFI_PARSE_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_AMSDU_PARSE_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_SA_TIMEOUT_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_DA_TIMEOUT_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_FLOW_TIMEOUT_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_FLUSH_REQUEST_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_AMSDU_FRAG_ERR,
+	HAL_REO_ENTR_RING_RXDMA_ECODE_MAX,
+};
+
+enum hal_rx_reo_dest_ring {
+	HAL_RX_REO_DEST_RING_TCL,
+	HAL_RX_REO_DEST_RING_SW1,
+	HAL_RX_REO_DEST_RING_SW2,
+	HAL_RX_REO_DEST_RING_SW3,
+	HAL_RX_REO_DEST_RING_SW4,
+	HAL_RX_REO_DEST_RING_RELEASE,
+	HAL_RX_REO_DEST_RING_FW,
+	HAL_RX_REO_DEST_RING_SW5,
+	HAL_RX_REO_DEST_RING_SW6,
+	HAL_RX_REO_DEST_RING_SW7,
+	HAL_RX_REO_DEST_RING_SW8,
+};
+
+#define HAL_REO_ENTR_RING_INFO0_QUEUE_ADDR_HI		GENMASK(7, 0)
+#define HAL_REO_ENTR_RING_INFO0_MPDU_BYTE_COUNT		GENMASK(21, 8)
+#define HAL_REO_ENTR_RING_INFO0_DEST_IND		GENMASK(26, 22)
+#define HAL_REO_ENTR_RING_INFO0_FRAMELESS_BAR		BIT(27)
+
+#define HAL_REO_ENTR_RING_INFO1_RXDMA_PUSH_REASON	GENMASK(1, 0)
+#define HAL_REO_ENTR_RING_INFO1_RXDMA_ERROR_CODE	GENMASK(6, 2)
+#define HAL_REO_ENTR_RING_INFO1_MPDU_FRAG_NUM		GENMASK(10, 7)
+#define HAL_REO_ENTR_RING_INFO1_SW_EXCEPTION		BIT(11)
+#define HAL_REO_ENTR_RING_INFO1_SW_EXCEPT_MPDU_DELINK	BIT(12)
+#define HAL_REO_ENTR_RING_INFO1_SW_EXCEPTION_RING_VLD	BIT(13)
+#define HAL_REO_ENTR_RING_INFO1_SW_EXCEPTION_RING	GENMASK(18, 14)
+#define HAL_REO_ENTR_RING_INFO1_MPDU_SEQ_NUM		GENMASK(30, 19)
+
+#define HAL_REO_ENTR_RING_INFO2_PHY_PPDU_ID		GENMASK(15, 0)
+#define HAL_REO_ENTR_RING_INFO2_SRC_LINK_ID		GENMASK(18, 16)
+#define HAL_REO_ENTR_RING_INFO2_RING_ID			GENMASK(27, 20)
+#define HAL_REO_ENTR_RING_INFO2_LOOPING_COUNT		GENMASK(31, 28)
+
+struct hal_reo_entrance_ring {
+	struct ath12k_buffer_addr buf_addr_info;
+	struct rx_mpdu_desc rx_mpdu_info;
+	__le32 queue_addr_lo;
+	__le32 info0; /* %HAL_REO_ENTR_RING_INFO0_ */
+	__le32 info1; /* %HAL_REO_ENTR_RING_INFO1_ */
+	__le32 info2; /* %HAL_REO_DEST_RING_INFO2_ */
+
+} __packed;
+
+/* hal_reo_entrance_ring
+ *
+ *		Producer: RXDMA
+ *		Consumer: REO
+ *
+ * buf_addr_info
+ *		Details of the physical address of a buffer or MSDU
+ *		link descriptor.
+ *
+ * rx_mpdu_info
+ *		General information related to the MPDU that is passed
+ *		on from REO entrance ring to the REO destination ring.
+ *
+ * queue_addr_lo
+ *		Address (lower 32 bits) of the REO queue descriptor.
+ *
+ * queue_addr_hi
+ *		Address (upper 8 bits) of the REO queue descriptor.
+ *
+ * mpdu_byte_count
+ *		An approximation of the number of bytes received in this MPDU.
+ *		Used to keeps stats on the amount of data flowing
+ *		through a queue.
+ *
+ * reo_destination_indication
+ *		The id of the reo exit ring where the msdu frame shall push
+ *		after (MPDU level) reordering has finished. Values are defined
+ *		in enum %HAL_RX_MSDU_DESC_REO_DEST_IND_.
+ *
+ * frameless_bar
+ *		Indicates that this REO entrance ring struct contains BAR info
+ *		from a multi TID BAR frame. The original multi TID BAR frame
+ *		itself contained all the REO info for the first TID, but all
+ *		the subsequent TID info and their linkage to the REO descriptors
+ *		is passed down as 'frameless' BAR info.
+ *
+ *		The only fields valid in this descriptor when this bit is set
+ *		are queue_addr_lo, queue_addr_hi, mpdu_sequence_number,
+ *		bar_frame and peer_meta_data.
+ *
+ * rxdma_push_reason
+ *		Reason for pushing this frame to this exit ring. Values are
+ *		defined in enum %HAL_REO_ENTR_RING_RXDMA_PUSH_REASON_.
+ *
+ * rxdma_error_code
+ *		Valid only when 'push_reason' is set. All error codes are
+ *		defined in enum %HAL_REO_ENTR_RING_RXDMA_ECODE_.
+ *
+ * mpdu_fragment_number
+ *		Field only valid when Reo_level_mpdu_frame_info.
+ *		Rx_mpdu_desc_info_details.Fragment_flag is set.
+ *
+ * sw_exception
+ *		When not set, REO is performing all its default MPDU processing
+ *		operations,
+ *		When set, this REO entrance descriptor is generated by FW, and
+ *		should be processed as an exception. This implies:
+ *		NO re-order function is needed.
+ *		MPDU delinking is determined by the setting of field
+ *		SW_excection_mpdu_delink
+ *
+ * sw_exception_mpdu_delink
+ *		Field only valid when SW_exception is set.
+ *		1'b0: REO should NOT delink the MPDU, and thus pass this
+ *			MPDU on to the destination ring as is. This implies that
+ *			in the REO_DESTINATION_RING struct field
+ *			Buf_or_link_desc_addr_info should point to an MSDU link
+ *			descriptor
+ *		1'b1: REO should perform the normal MPDU delink into MSDU operations.
+ *
+ * sw_exception_dest_ring
+ *		Field only valid when fields SW_exception and SW
+ *		exception_destination_ring_valid are set. values are defined
+ *		in %HAL_RX_REO_DEST_RING_.
+ *
+ * mpdu_seq_number
+ *		The field can have two different meanings based on the setting
+ *		of sub-field Reo level mpdu frame info.
+ *		Rx_mpdu_desc_info_details. BAR_frame
+ *		'BAR_frame' is NOT set:
+ *		The MPDU sequence number of the received frame.
+ *		'BAR_frame' is set.
+ *		The MPDU Start sequence number from the BAR frame
+ *
+ * phy_ppdu_id
+ *		A PPDU counter value that PHY increments for every PPDU received
+ *
+ * src_link_id
+ *		Set to the link ID of the PMAC that received the frame
+ *
+ * ring_id
+ *		The buffer pointer ring id.
+ *		0 - Idle ring
+ *		1 - N refers to other rings.
+ *
+ * looping_count
+ *		Indicates the number of times the producer of entries into
+ *		this ring has looped around the ring.
+ */
+
+#define HAL_REO_CMD_HDR_INFO0_CMD_NUMBER	GENMASK(15, 0)
+#define HAL_REO_CMD_HDR_INFO0_STATUS_REQUIRED	BIT(16)
+
+struct hal_reo_cmd_hdr {
+	__le32 info0;
+} __packed;
+
+#define HAL_REO_GET_QUEUE_STATS_INFO0_QUEUE_ADDR_HI	GENMASK(7, 0)
+#define HAL_REO_GET_QUEUE_STATS_INFO0_CLEAR_STATS	BIT(8)
+
+struct hal_reo_get_queue_stats {
+	struct hal_reo_cmd_hdr cmd;
+	__le32 queue_addr_lo;
+	__le32 info0;
+	__le32 rsvd0[6];
+	__le32 tlv64_pad;
+} __packed;
+
+/* hal_reo_get_queue_stats
+ *		Producer: SW
+ *		Consumer: REO
+ *
+ * cmd
+ *		Details for command execution tracking purposes.
+ *
+ * queue_addr_lo
+ *		Address (lower 32 bits) of the REO queue descriptor.
+ *
+ * queue_addr_hi
+ *		Address (upper 8 bits) of the REO queue descriptor.
+ *
+ * clear_stats
+ *		Clear stats settings. When set, Clear the stats after
+ *		generating the status.
+ *
+ *		Following stats will be cleared.
+ *		Timeout_count
+ *		Forward_due_to_bar_count
+ *		Duplicate_count
+ *		Frames_in_order_count
+ *		BAR_received_count
+ *		MPDU_Frames_processed_count
+ *		MSDU_Frames_processed_count
+ *		Total_processed_byte_count
+ *		Late_receive_MPDU_count
+ *		window_jump_2k
+ *		Hole_count
+ */
+
+#define HAL_REO_FLUSH_QUEUE_INFO0_DESC_ADDR_HI		GENMASK(7, 0)
+#define HAL_REO_FLUSH_QUEUE_INFO0_BLOCK_DESC_ADDR	BIT(8)
+#define HAL_REO_FLUSH_QUEUE_INFO0_BLOCK_RESRC_IDX	GENMASK(10, 9)
+
+struct hal_reo_flush_queue {
+	struct hal_reo_cmd_hdr cmd;
+	__le32 desc_addr_lo;
+	__le32 info0;
+	__le32 rsvd0[6];
+} __packed;
+
+#define HAL_REO_FLUSH_CACHE_INFO0_CACHE_ADDR_HI		GENMASK(7, 0)
+#define HAL_REO_FLUSH_CACHE_INFO0_FWD_ALL_MPDUS		BIT(8)
+#define HAL_REO_FLUSH_CACHE_INFO0_RELEASE_BLOCK_IDX	BIT(9)
+#define HAL_REO_FLUSH_CACHE_INFO0_BLOCK_RESRC_IDX	GENMASK(11, 10)
+#define HAL_REO_FLUSH_CACHE_INFO0_FLUSH_WO_INVALIDATE	BIT(12)
+#define HAL_REO_FLUSH_CACHE_INFO0_BLOCK_CACHE_USAGE	BIT(13)
+#define HAL_REO_FLUSH_CACHE_INFO0_FLUSH_ALL		BIT(14)
+
+struct hal_reo_flush_cache {
+	struct hal_reo_cmd_hdr cmd;
+	__le32 cache_addr_lo;
+	__le32 info0;
+	__le32 rsvd0[6];
+} __packed;
+
+#define HAL_TCL_DATA_CMD_INFO0_CMD_TYPE			BIT(0)
+#define HAL_TCL_DATA_CMD_INFO0_DESC_TYPE		BIT(1)
+#define HAL_TCL_DATA_CMD_INFO0_BANK_ID			GENMASK(7, 2)
+#define HAL_TCL_DATA_CMD_INFO0_TX_NOTIFY_FRAME		GENMASK(10, 8)
+#define HAL_TCL_DATA_CMD_INFO0_HDR_LEN_READ_SEL		BIT(11)
+#define HAL_TCL_DATA_CMD_INFO0_BUF_TIMESTAMP		GENMASK(30, 12)
+#define HAL_TCL_DATA_CMD_INFO0_BUF_TIMESTAMP_VLD	BIT(31)
+
+#define HAL_TCL_DATA_CMD_INFO1_CMD_NUM		GENMASK(31, 16)
+
+#define HAL_TCL_DATA_CMD_INFO2_DATA_LEN		GENMASK(15, 0)
+#define HAL_TCL_DATA_CMD_INFO2_IP4_CKSUM_EN	BIT(16)
+#define HAL_TCL_DATA_CMD_INFO2_UDP4_CKSUM_EN	BIT(17)
+#define HAL_TCL_DATA_CMD_INFO2_UDP6_CKSUM_EN	BIT(18)
+#define HAL_TCL_DATA_CMD_INFO2_TCP4_CKSUM_EN	BIT(19)
+#define HAL_TCL_DATA_CMD_INFO2_TCP6_CKSUM_EN	BIT(20)
+#define HAL_TCL_DATA_CMD_INFO2_TO_FW		BIT(21)
+#define HAL_TCL_DATA_CMD_INFO2_PKT_OFFSET	GENMASK(31, 23)
+
+#define HAL_TCL_DATA_CMD_INFO3_TID_OVERWRITE		BIT(0)
+#define HAL_TCL_DATA_CMD_INFO3_FLOW_OVERRIDE_EN		BIT(1)
+#define HAL_TCL_DATA_CMD_INFO3_CLASSIFY_INFO_SEL	GENMASK(3, 2)
+#define HAL_TCL_DATA_CMD_INFO3_TID			GENMASK(7, 4)
+#define HAL_TCL_DATA_CMD_INFO3_FLOW_OVERRIDE		BIT(8)
+#define HAL_TCL_DATA_CMD_INFO3_PMAC_ID			GENMASK(10, 9)
+#define HAL_TCL_DATA_CMD_INFO3_MSDU_COLOR		GENMASK(12, 11)
+#define HAL_TCL_DATA_CMD_INFO3_VDEV_ID			GENMASK(31, 24)
+
+#define HAL_TCL_DATA_CMD_INFO4_SEARCH_INDEX		GENMASK(19, 0)
+#define HAL_TCL_DATA_CMD_INFO4_CACHE_SET_NUM		GENMASK(23, 20)
+#define HAL_TCL_DATA_CMD_INFO4_IDX_LOOKUP_OVERRIDE	BIT(24)
+
+#define HAL_TCL_DATA_CMD_INFO5_RING_ID			GENMASK(27, 20)
+#define HAL_TCL_DATA_CMD_INFO5_LOOPING_COUNT		GENMASK(31, 28)
+
+enum hal_encrypt_type {
+	HAL_ENCRYPT_TYPE_WEP_40,
+	HAL_ENCRYPT_TYPE_WEP_104,
+	HAL_ENCRYPT_TYPE_TKIP_NO_MIC,
+	HAL_ENCRYPT_TYPE_WEP_128,
+	HAL_ENCRYPT_TYPE_TKIP_MIC,
+	HAL_ENCRYPT_TYPE_WAPI,
+	HAL_ENCRYPT_TYPE_CCMP_128,
+	HAL_ENCRYPT_TYPE_OPEN,
+	HAL_ENCRYPT_TYPE_CCMP_256,
+	HAL_ENCRYPT_TYPE_GCMP_128,
+	HAL_ENCRYPT_TYPE_AES_GCMP_256,
+	HAL_ENCRYPT_TYPE_WAPI_GCM_SM4,
+};
+
+enum hal_tcl_encap_type {
+	HAL_TCL_ENCAP_TYPE_RAW,
+	HAL_TCL_ENCAP_TYPE_NATIVE_WIFI,
+	HAL_TCL_ENCAP_TYPE_ETHERNET,
+	HAL_TCL_ENCAP_TYPE_802_3 = 3,
+};
+
+enum hal_tcl_desc_type {
+	HAL_TCL_DESC_TYPE_BUFFER,
+	HAL_TCL_DESC_TYPE_EXT_DESC,
+};
+
+enum hal_wbm_htt_tx_comp_status {
+	HAL_WBM_REL_HTT_TX_COMP_STATUS_OK,
+	HAL_WBM_REL_HTT_TX_COMP_STATUS_DROP,
+	HAL_WBM_REL_HTT_TX_COMP_STATUS_TTL,
+	HAL_WBM_REL_HTT_TX_COMP_STATUS_REINJ,
+	HAL_WBM_REL_HTT_TX_COMP_STATUS_INSPECT,
+	HAL_WBM_REL_HTT_TX_COMP_STATUS_MEC_NOTIFY,
+	HAL_WBM_REL_HTT_TX_COMP_STATUS_MAX,
+};
+
+struct hal_tcl_data_cmd {
+	struct ath12k_buffer_addr buf_addr_info;
+	__le32 info0;
+	__le32 info1;
+	__le32 info2;
+	__le32 info3;
+	__le32 info4;
+	__le32 info5;
+} __packed;
+
+/* hal_tcl_data_cmd
+ *
+ * buf_addr_info
+ *		Details of the physical address of a buffer or MSDU
+ *		link descriptor.
+ *
+ * tcl_cmd_type
+ *		used to select the type of TCL Command decriptor
+ *
+ * desc_type
+ *		Indicates the type of address provided in the buf_addr_info.
+ *		Values are defined in enum %HAL_REO_DEST_RING_BUFFER_TYPE_.
+ *
+ * bank_id
+ *		used to select one of the TCL register banks for fields removed
+ *		from 'TCL_DATA_CMD' that do not change often within one virtual
+ *		device or a set of virtual devices:
+ *
+ * tx_notify_frame
+ *		TCL copies this value to 'TQM_ENTRANCE_RING' field FW_tx_notify_frame.
+ *
+ * hdr_length_read_sel
+ *		used to select the per 'encap_type' register set for MSDU header
+ *		read length
+ *
+ * buffer_timestamp
+ * buffer_timestamp_valid
+ *		Frame system entrance timestamp. It shall be filled by first
+ *		module (SW, TCL or TQM) that sees the frames first.
+ *
+ * cmd_num
+ *		This number can be used to match against status.
+ *
+ * data_length
+ *		MSDU length in case of direct descriptor. Length of link
+ *		extension descriptor in case of Link extension descriptor.
+ *
+ * *_checksum_en
+ *		Enable checksum replacement for ipv4, udp_over_ipv4, ipv6,
+ *		udp_over_ipv6, tcp_over_ipv4 and tcp_over_ipv6.
+ *
+ * to_fw
+ *		Forward packet to FW along with classification result. The
+ *		packet will not be forward to TQM when this bit is set.
+ *		1'b0: Use classification result to forward the packet.
+ *		1'b1: Override classification result & forward packet only to fw
+ *
+ * packet_offset
+ *		Packet offset from Metadata in case of direct buffer descriptor.
+ *
+ * hlos_tid_overwrite
+ *
+ *		When set, TCL shall ignore the IP DSCP and VLAN PCP
+ *		fields and use HLOS_TID as the final TID. Otherwise TCL
+ *		shall consider the DSCP and PCP fields as well as HLOS_TID
+ *		and choose a final TID based on the configured priority
+ *
+ * flow_override_enable
+ *		TCL uses this to select the flow pointer from the peer table,
+ *		which can be overridden by SW for pre-encrypted raw WiFi packets
+ *		that cannot be parsed for UDP or for other MLO
+ *		0 - FP_PARSE_IP: Use the flow-pointer based on parsing the IPv4
+ *				 or IPv6 header.
+ *		1 - FP_USE_OVERRIDE: Use the who_classify_info_sel and
+ *				     flow_override fields to select the flow-pointer
+ *
+ * who_classify_info_sel
+ *		Field only valid when flow_override_enable is set to FP_USE_OVERRIDE.
+ *		This field is used to select  one of the 'WHO_CLASSIFY_INFO's in the
+ *		peer table in case more than 2 flows are mapped to a single TID.
+ *		0: To choose Flow 0 and 1 of any TID use this value.
+ *		1: To choose Flow 2 and 3 of any TID use this value.
+ *		2: To choose Flow 4 and 5 of any TID use this value.
+ *		3: To choose Flow 6 and 7 of any TID use this value.
+ *
+ *		If who_classify_info sel is not in sync with the num_tx_classify_info
+ *		field from address search, then TCL will set 'who_classify_info_sel'
+ *		to 0 use flows 0 and 1.
+ *
+ * hlos_tid
+ *		HLOS MSDU priority
+ *		Field is used when HLOS_TID_overwrite is set.
+ *
+ * flow_override
+ *		Field only valid when flow_override_enable is set to FP_USE_OVERRIDE
+ *		TCL uses this to select the flow pointer from the peer table,
+ *		which can be overridden by SW for pre-encrypted raw WiFi packets
+ *		that cannot be parsed for UDP or for other MLO
+ *		0 - FP_USE_NON_UDP: Use the non-UDP flow pointer (flow 0)
+ *		1 - FP_USE_UDP: Use the UDP flow pointer (flow 1)
+ *
+ * pmac_id
+ *		TCL uses this PMAC_ID in address search, i.e, while
+ *		finding matching entry for the packet in AST corresponding
+ *		to given PMAC_ID
+ *
+ *		If PMAC ID is all 1s (=> value 3), it indicates wildcard
+ *		match for any PMAC
+ *
+ * vdev_id
+ *		Virtual device ID to check against the address search entry to
+ *		avoid security issues from transmitting packets from an incorrect
+ *		virtual device
+ *
+ * search_index
+ *		The index that will be used for index based address or
+ *		flow search. The field is valid when 'search_type' is  1 or 2.
+ *
+ * cache_set_num
+ *
+ *		Cache set number that should be used to cache the index
+ *		based search results, for address and flow search. This
+ *		value should be equal to LSB four bits of the hash value of
+ *		match data, in case of search index points to an entry which
+ *		may be used in content based search also. The value can be
+ *		anything when the entry pointed by search index will not be
+ *		used for content based search.
+ *
+ * index_loop_override
+ *		When set, address search and packet routing is forced to use
+ *		'search_index' instead of following the register configuration
+ *		seleced by Bank_id.
+ *
+ * ring_id
+ *		The buffer pointer ring ID.
+ *		0 refers to the IDLE ring
+ *		1 - N refers to other rings
+ *
+ * looping_count
+ *
+ *		A count value that indicates the number of times the
+ *		producer of entries into the Ring has looped around the
+ *		ring.
+ *
+ *		At initialization time, this value is set to 0. On the
+ *		first loop, this value is set to 1. After the max value is
+ *		reached allowed by the number of bits for this field, the
+ *		count value continues with 0 again.
+ *
+ *		In case SW is the consumer of the ring entries, it can
+ *		use this field to figure out up to where the producer of
+ *		entries has created new entries. This eliminates the need to
+ *		check where the head pointer' of the ring is located once
+ *		the SW starts processing an interrupt indicating that new
+ *		entries have been put into this ring...
+ *
+ *		Also note that SW if it wants only needs to look at the
+ *		LSB bit of this count value.
+ */
+
+#define HAL_TCL_DESC_LEN sizeof(struct hal_tcl_data_cmd)
+
+#define HAL_TX_MSDU_EXT_INFO0_BUF_PTR_LO	GENMASK(31, 0)
+
+#define HAL_TX_MSDU_EXT_INFO1_BUF_PTR_HI	GENMASK(7, 0)
+#define HAL_TX_MSDU_EXT_INFO1_EXTN_OVERRIDE	BIT(8)
+#define HAL_TX_MSDU_EXT_INFO1_ENCAP_TYPE	GENMASK(10, 9)
+#define HAL_TX_MSDU_EXT_INFO1_ENCRYPT_TYPE	GENMASK(14, 11)
+#define HAL_TX_MSDU_EXT_INFO1_BUF_LEN		GENMASK(31, 16)
+
+struct hal_tx_msdu_ext_desc {
+	__le32 rsvd0[6];
+	__le32 info0;
+	__le32 info1;
+	__le32 rsvd1[10];
+};
+
+struct hal_tcl_gse_cmd {
+	__le32 ctrl_buf_addr_lo;
+	__le32 info0;
+	__le32 meta_data[2];
+	__le32 rsvd0[2];
+	__le32 info1;
+} __packed;
+
+/* hal_tcl_gse_cmd
+ *
+ * ctrl_buf_addr_lo, ctrl_buf_addr_hi
+ *		Address of a control buffer containing additional info needed
+ *		for this command execution.
+ *
+ * meta_data
+ *		Meta data to be returned in the status descriptor
+ */
+
+enum hal_tcl_cache_op_res {
+	HAL_TCL_CACHE_OP_RES_DONE,
+	HAL_TCL_CACHE_OP_RES_NOT_FOUND,
+	HAL_TCL_CACHE_OP_RES_TIMEOUT,
+};
+
+struct hal_tcl_status_ring {
+	__le32 info0;
+	__le32 msdu_byte_count;
+	__le32 msdu_timestamp;
+	__le32 meta_data[2];
+	__le32 info1;
+	__le32 rsvd0;
+	__le32 info2;
+} __packed;
+
+/* hal_tcl_status_ring
+ *
+ * msdu_cnt
+ * msdu_byte_count
+ *		MSDU count of Entry and MSDU byte count for entry 1.
+ *
+ */
+
+#define HAL_CE_SRC_DESC_ADDR_INFO_ADDR_HI	GENMASK(7, 0)
+#define HAL_CE_SRC_DESC_ADDR_INFO_HASH_EN	BIT(8)
+#define HAL_CE_SRC_DESC_ADDR_INFO_BYTE_SWAP	BIT(9)
+#define HAL_CE_SRC_DESC_ADDR_INFO_DEST_SWAP	BIT(10)
+#define HAL_CE_SRC_DESC_ADDR_INFO_GATHER	BIT(11)
+#define HAL_CE_SRC_DESC_ADDR_INFO_LEN		GENMASK(31, 16)
+
+#define HAL_CE_SRC_DESC_META_INFO_DATA		GENMASK(15, 0)
+
+#define HAL_CE_SRC_DESC_FLAGS_RING_ID		GENMASK(27, 20)
+#define HAL_CE_SRC_DESC_FLAGS_LOOP_CNT		HAL_SRNG_DESC_LOOP_CNT
+
+struct hal_ce_srng_src_desc {
+	__le32 buffer_addr_low;
+	__le32 buffer_addr_info; /* %HAL_CE_SRC_DESC_ADDR_INFO_ */
+	__le32 meta_info; /* %HAL_CE_SRC_DESC_META_INFO_ */
+	__le32 flags; /* %HAL_CE_SRC_DESC_FLAGS_ */
+} __packed;
+
+/* hal_ce_srng_src_desc
+ *
+ * buffer_addr_lo
+ *		LSB 32 bits of the 40 Bit Pointer to the source buffer
+ *
+ * buffer_addr_hi
+ *		MSB 8 bits of the 40 Bit Pointer to the source buffer
+ *
+ * toeplitz_en
+ *		Enable generation of 32-bit Toeplitz-LFSR hash for
+ *		data transfer. In case of gather field in first source
+ *		ring entry of the gather copy cycle in taken into account.
+ *
+ * src_swap
+ *		Treats source memory organization as big-endian. For
+ *		each dword read (4 bytes), the byte 0 is swapped with byte 3
+ *		and byte 1 is swapped with byte 2.
+ *		In case of gather field in first source ring entry of
+ *		the gather copy cycle in taken into account.
+ *
+ * dest_swap
+ *		Treats destination memory organization as big-endian.
+ *		For each dword write (4 bytes), the byte 0 is swapped with
+ *		byte 3 and byte 1 is swapped with byte 2.
+ *		In case of gather field in first source ring entry of
+ *		the gather copy cycle in taken into account.
+ *
+ * gather
+ *		Enables gather of multiple copy engine source
+ *		descriptors to one destination.
+ *
+ * ce_res_0
+ *		Reserved
+ *
+ *
+ * length
+ *		Length of the buffer in units of octets of the current
+ *		descriptor
+ *
+ * fw_metadata
+ *		Meta data used by FW.
+ *		In case of gather field in first source ring entry of
+ *		the gather copy cycle in taken into account.
+ *
+ * ce_res_1
+ *		Reserved
+ *
+ * ce_res_2
+ *		Reserved
+ *
+ * ring_id
+ *		The buffer pointer ring ID.
+ *		0 refers to the IDLE ring
+ *		1 - N refers to other rings
+ *		Helps with debugging when dumping ring contents.
+ *
+ * looping_count
+ *		A count value that indicates the number of times the
+ *		producer of entries into the Ring has looped around the
+ *		ring.
+ *
+ *		At initialization time, this value is set to 0. On the
+ *		first loop, this value is set to 1. After the max value is
+ *		reached allowed by the number of bits for this field, the
+ *		count value continues with 0 again.
+ *
+ *		In case SW is the consumer of the ring entries, it can
+ *		use this field to figure out up to where the producer of
+ *		entries has created new entries. This eliminates the need to
+ *		check where the head pointer' of the ring is located once
+ *		the SW starts processing an interrupt indicating that new
+ *		entries have been put into this ring...
+ *
+ *		Also note that SW if it wants only needs to look at the
+ *		LSB bit of this count value.
+ */
+
+#define HAL_CE_DEST_DESC_ADDR_INFO_ADDR_HI		GENMASK(7, 0)
+#define HAL_CE_DEST_DESC_ADDR_INFO_RING_ID		GENMASK(27, 20)
+#define HAL_CE_DEST_DESC_ADDR_INFO_LOOP_CNT		HAL_SRNG_DESC_LOOP_CNT
+
+struct hal_ce_srng_dest_desc {
+	__le32 buffer_addr_low;
+	__le32 buffer_addr_info; /* %HAL_CE_DEST_DESC_ADDR_INFO_ */
+} __packed;
+
+/* hal_ce_srng_dest_desc
+ *
+ * dst_buffer_low
+ *		LSB 32 bits of the 40 Bit Pointer to the Destination
+ *		buffer
+ *
+ * dst_buffer_high
+ *		MSB 8 bits of the 40 Bit Pointer to the Destination
+ *		buffer
+ *
+ * ce_res_4
+ *		Reserved
+ *
+ * ring_id
+ *		The buffer pointer ring ID.
+ *		0 refers to the IDLE ring
+ *		1 - N refers to other rings
+ *		Helps with debugging when dumping ring contents.
+ *
+ * looping_count
+ *		A count value that indicates the number of times the
+ *		producer of entries into the Ring has looped around the
+ *		ring.
+ *
+ *		At initialization time, this value is set to 0. On the
+ *		first loop, this value is set to 1. After the max value is
+ *		reached allowed by the number of bits for this field, the
+ *		count value continues with 0 again.
+ *
+ *		In case SW is the consumer of the ring entries, it can
+ *		use this field to figure out up to where the producer of
+ *		entries has created new entries. This eliminates the need to
+ *		check where the head pointer' of the ring is located once
+ *		the SW starts processing an interrupt indicating that new
+ *		entries have been put into this ring...
+ *
+ *		Also note that SW if it wants only needs to look at the
+ *		LSB bit of this count value.
+ */
+
+#define HAL_CE_DST_STATUS_DESC_FLAGS_HASH_EN		BIT(8)
+#define HAL_CE_DST_STATUS_DESC_FLAGS_BYTE_SWAP		BIT(9)
+#define HAL_CE_DST_STATUS_DESC_FLAGS_DEST_SWAP		BIT(10)
+#define HAL_CE_DST_STATUS_DESC_FLAGS_GATHER		BIT(11)
+#define HAL_CE_DST_STATUS_DESC_FLAGS_LEN		GENMASK(31, 16)
+
+#define HAL_CE_DST_STATUS_DESC_META_INFO_DATA		GENMASK(15, 0)
+#define HAL_CE_DST_STATUS_DESC_META_INFO_RING_ID	GENMASK(27, 20)
+#define HAL_CE_DST_STATUS_DESC_META_INFO_LOOP_CNT	HAL_SRNG_DESC_LOOP_CNT
+
+struct hal_ce_srng_dst_status_desc {
+	__le32 flags; /* %HAL_CE_DST_STATUS_DESC_FLAGS_ */
+	__le32 toeplitz_hash0;
+	__le32 toeplitz_hash1;
+	__le32 meta_info; /* HAL_CE_DST_STATUS_DESC_META_INFO_ */
+} __packed;
+
+/* hal_ce_srng_dst_status_desc
+ *
+ * ce_res_5
+ *		Reserved
+ *
+ * toeplitz_en
+ *
+ * src_swap
+ *		Source memory buffer swapped
+ *
+ * dest_swap
+ *		Destination  memory buffer swapped
+ *
+ * gather
+ *		Gather of multiple copy engine source descriptors to one
+ *		destination enabled
+ *
+ * ce_res_6
+ *		Reserved
+ *
+ * length
+ *		Sum of all the Lengths of the source descriptor in the
+ *		gather chain
+ *
+ * toeplitz_hash_0
+ *		32 LS bits of 64 bit Toeplitz LFSR hash result
+ *
+ * toeplitz_hash_1
+ *		32 MS bits of 64 bit Toeplitz LFSR hash result
+ *
+ * fw_metadata
+ *		Meta data used by FW
+ *		In case of gather field in first source ring entry of
+ *		the gather copy cycle in taken into account.
+ *
+ * ce_res_7
+ *		Reserved
+ *
+ * ring_id
+ *		The buffer pointer ring ID.
+ *		0 refers to the IDLE ring
+ *		1 - N refers to other rings
+ *		Helps with debugging when dumping ring contents.
+ *
+ * looping_count
+ *		A count value that indicates the number of times the
+ *		producer of entries into the Ring has looped around the
+ *		ring.
+ *
+ *		At initialization time, this value is set to 0. On the
+ *		first loop, this value is set to 1. After the max value is
+ *		reached allowed by the number of bits for this field, the
+ *		count value continues with 0 again.
+ *
+ *		In case SW is the consumer of the ring entries, it can
+ *		use this field to figure out up to where the producer of
+ *		entries has created new entries. This eliminates the need to
+ *		check where the head pointer' of the ring is located once
+ *		the SW starts processing an interrupt indicating that new
+ *		entries have been put into this ring...
+ *
+ *		Also note that SW if it wants only needs to look at the
+ *			LSB bit of this count value.
+ */
+
+#define HAL_TX_RATE_STATS_INFO0_VALID		BIT(0)
+#define HAL_TX_RATE_STATS_INFO0_BW		GENMASK(3, 1)
+#define HAL_TX_RATE_STATS_INFO0_PKT_TYPE	GENMASK(7, 4)
+#define HAL_TX_RATE_STATS_INFO0_STBC		BIT(8)
+#define HAL_TX_RATE_STATS_INFO0_LDPC		BIT(9)
+#define HAL_TX_RATE_STATS_INFO0_SGI		GENMASK(11, 10)
+#define HAL_TX_RATE_STATS_INFO0_MCS		GENMASK(15, 12)
+#define HAL_TX_RATE_STATS_INFO0_OFDMA_TX	BIT(16)
+#define HAL_TX_RATE_STATS_INFO0_TONES_IN_RU	GENMASK(28, 17)
+
+enum hal_tx_rate_stats_bw {
+	HAL_TX_RATE_STATS_BW_20,
+	HAL_TX_RATE_STATS_BW_40,
+	HAL_TX_RATE_STATS_BW_80,
+	HAL_TX_RATE_STATS_BW_160,
+};
+
+enum hal_tx_rate_stats_pkt_type {
+	HAL_TX_RATE_STATS_PKT_TYPE_11A,
+	HAL_TX_RATE_STATS_PKT_TYPE_11B,
+	HAL_TX_RATE_STATS_PKT_TYPE_11N,
+	HAL_TX_RATE_STATS_PKT_TYPE_11AC,
+	HAL_TX_RATE_STATS_PKT_TYPE_11AX,
+	HAL_TX_RATE_STATS_PKT_TYPE_11BA,
+	HAL_TX_RATE_STATS_PKT_TYPE_11BE,
+};
+
+enum hal_tx_rate_stats_sgi {
+	HAL_TX_RATE_STATS_SGI_08US,
+	HAL_TX_RATE_STATS_SGI_04US,
+	HAL_TX_RATE_STATS_SGI_16US,
+	HAL_TX_RATE_STATS_SGI_32US,
+};
+
+struct hal_tx_rate_stats {
+	__le32 info0;
+	__le32 tsf;
+} __packed;
+
+struct hal_wbm_link_desc {
+	struct ath12k_buffer_addr buf_addr_info;
+} __packed;
+
+/* hal_wbm_link_desc
+ *
+ *	Producer: WBM
+ *	Consumer: WBM
+ *
+ * buf_addr_info
+ *		Details of the physical address of a buffer or MSDU
+ *		link descriptor.
+ */
+
+enum hal_wbm_rel_src_module {
+	HAL_WBM_REL_SRC_MODULE_TQM,
+	HAL_WBM_REL_SRC_MODULE_RXDMA,
+	HAL_WBM_REL_SRC_MODULE_REO,
+	HAL_WBM_REL_SRC_MODULE_FW,
+	HAL_WBM_REL_SRC_MODULE_SW,
+};
+
+enum hal_wbm_rel_desc_type {
+	HAL_WBM_REL_DESC_TYPE_REL_MSDU,
+	HAL_WBM_REL_DESC_TYPE_MSDU_LINK,
+	HAL_WBM_REL_DESC_TYPE_MPDU_LINK,
+	HAL_WBM_REL_DESC_TYPE_MSDU_EXT,
+	HAL_WBM_REL_DESC_TYPE_QUEUE_EXT,
+};
+
+/* hal_wbm_rel_desc_type
+ *
+ * msdu_buffer
+ *	The address points to an MSDU buffer
+ *
+ * msdu_link_descriptor
+ *	The address points to an Tx MSDU link descriptor
+ *
+ * mpdu_link_descriptor
+ *	The address points to an MPDU link descriptor
+ *
+ * msdu_ext_descriptor
+ *	The address points to an MSDU extension descriptor
+ *
+ * queue_ext_descriptor
+ *	The address points to an TQM queue extension descriptor. WBM should
+ *	treat this is the same way as a link descriptor.
+ */
+
+enum hal_wbm_rel_bm_act {
+	HAL_WBM_REL_BM_ACT_PUT_IN_IDLE,
+	HAL_WBM_REL_BM_ACT_REL_MSDU,
+};
+
+/* hal_wbm_rel_bm_act
+ *
+ * put_in_idle_list
+ *	Put the buffer or descriptor back in the idle list. In case of MSDU or
+ *	MDPU link descriptor, BM does not need to check to release any
+ *	individual MSDU buffers.
+ *
+ * release_msdu_list
+ *	This BM action can only be used in combination with desc_type being
+ *	msdu_link_descriptor. Field first_msdu_index points out which MSDU
+ *	pointer in the MSDU link descriptor is the first of an MPDU that is
+ *	released. BM shall release all the MSDU buffers linked to this first
+ *	MSDU buffer pointer. All related MSDU buffer pointer entries shall be
+ *	set to value 0, which represents the 'NULL' pointer. When all MSDU
+ *	buffer pointers in the MSDU link descriptor are 'NULL', the MSDU link
+ *	descriptor itself shall also be released.
+ */
+#define HAL_WBM_COMPL_RX_INFO0_REL_SRC_MODULE		GENMASK(2, 0)
+#define HAL_WBM_COMPL_RX_INFO0_BM_ACTION		GENMASK(5, 3)
+#define HAL_WBM_COMPL_RX_INFO0_DESC_TYPE		GENMASK(8, 6)
+#define HAL_WBM_COMPL_RX_INFO0_RBM			GENMASK(12, 9)
+#define HAL_WBM_COMPL_RX_INFO0_RXDMA_PUSH_REASON	GENMASK(18, 17)
+#define HAL_WBM_COMPL_RX_INFO0_RXDMA_ERROR_CODE		GENMASK(23, 19)
+#define HAL_WBM_COMPL_RX_INFO0_REO_PUSH_REASON		GENMASK(25, 24)
+#define HAL_WBM_COMPL_RX_INFO0_REO_ERROR_CODE		GENMASK(30, 26)
+#define HAL_WBM_COMPL_RX_INFO0_WBM_INTERNAL_ERROR	BIT(31)
+
+#define HAL_WBM_COMPL_RX_INFO1_PHY_ADDR_HI		GENMASK(7, 0)
+#define HAL_WBM_COMPL_RX_INFO1_SW_COOKIE		GENMASK(27, 8)
+#define HAL_WBM_COMPL_RX_INFO1_LOOPING_COUNT		GENMASK(31, 28)
+
+struct hal_wbm_completion_ring_rx {
+	__le32 addr_lo;
+	__le32 addr_hi;
+	__le32 info0;
+	struct rx_mpdu_desc rx_mpdu_info;
+	struct rx_msdu_desc rx_msdu_info;
+	__le32 phy_addr_lo;
+	__le32 info1;
+} __packed;
+
+#define HAL_WBM_COMPL_TX_INFO0_REL_SRC_MODULE		GENMASK(2, 0)
+#define HAL_WBM_COMPL_TX_INFO0_DESC_TYPE		GENMASK(8, 6)
+#define HAL_WBM_COMPL_TX_INFO0_RBM			GENMASK(12, 9)
+#define HAL_WBM_COMPL_TX_INFO0_TQM_RELEASE_REASON	GENMASK(16, 13)
+#define HAL_WBM_COMPL_TX_INFO0_RBM_OVERRIDE_VLD		BIT(17)
+#define HAL_WBM_COMPL_TX_INFO0_SW_COOKIE_LO		GENMASK(29, 18)
+#define HAL_WBM_COMPL_TX_INFO0_CC_DONE			BIT(30)
+#define HAL_WBM_COMPL_TX_INFO0_WBM_INTERNAL_ERROR	BIT(31)
+
+#define HAL_WBM_COMPL_TX_INFO1_TQM_STATUS_NUMBER	GENMASK(23, 0)
+#define HAL_WBM_COMPL_TX_INFO1_TRANSMIT_COUNT		GENMASK(30, 24)
+#define HAL_WBM_COMPL_TX_INFO1_SW_REL_DETAILS_VALID	BIT(31)
+
+#define HAL_WBM_COMPL_TX_INFO2_ACK_FRAME_RSSI		GENMASK(7, 0)
+#define HAL_WBM_COMPL_TX_INFO2_FIRST_MSDU		BIT(8)
+#define HAL_WBM_COMPL_TX_INFO2_LAST_MSDU		BIT(9)
+#define HAL_WBM_COMPL_TX_INFO2_FW_TX_NOTIF_FRAME	GENMASK(12, 10)
+#define HAL_WBM_COMPL_TX_INFO2_BUFFER_TIMESTAMP		GENMASK(31, 13)
+
+#define HAL_WBM_COMPL_TX_INFO3_PEER_ID			GENMASK(15, 0)
+#define HAL_WBM_COMPL_TX_INFO3_TID			GENMASK(19, 16)
+#define HAL_WBM_COMPL_TX_INFO3_SW_COOKIE_HI		GENMASK(27, 20)
+#define HAL_WBM_COMPL_TX_INFO3_LOOPING_COUNT		GENMASK(31, 28)
+
+struct hal_wbm_completion_ring_tx {
+	__le32 buf_va_lo;
+	__le32 buf_va_hi;
+	__le32 info0;
+	__le32 info1;
+	__le32 info2;
+	struct hal_tx_rate_stats rate_stats;
+	__le32 info3;
+} __packed;
+
+#define HAL_WBM_RELEASE_TX_INFO0_REL_SRC_MODULE		GENMASK(2, 0)
+#define HAL_WBM_RELEASE_TX_INFO0_BM_ACTION		GENMASK(5, 3)
+#define HAL_WBM_RELEASE_TX_INFO0_DESC_TYPE		GENMASK(8, 6)
+#define HAL_WBM_RELEASE_TX_INFO0_FIRST_MSDU_IDX		GENMASK(12, 9)
+#define HAL_WBM_RELEASE_TX_INFO0_TQM_RELEASE_REASON	GENMASK(18, 13)
+#define HAL_WBM_RELEASE_TX_INFO0_RBM_OVERRIDE_VLD	BIT(17)
+#define HAL_WBM_RELEASE_TX_INFO0_SW_BUFFER_COOKIE_11_0	GENMASK(29, 18)
+#define HAL_WBM_RELEASE_TX_INFO0_WBM_INTERNAL_ERROR	BIT(31)
+
+#define HAL_WBM_RELEASE_TX_INFO1_TQM_STATUS_NUMBER	GENMASK(23, 0)
+#define HAL_WBM_RELEASE_TX_INFO1_TRANSMIT_COUNT		GENMASK(30, 24)
+#define HAL_WBM_RELEASE_TX_INFO1_SW_REL_DETAILS_VALID	BIT(31)
+
+#define HAL_WBM_RELEASE_TX_INFO2_ACK_FRAME_RSSI		GENMASK(7, 0)
+#define HAL_WBM_RELEASE_TX_INFO2_FIRST_MSDU		BIT(8)
+#define HAL_WBM_RELEASE_TX_INFO2_LAST_MSDU		BIT(9)
+#define HAL_WBM_RELEASE_TX_INFO2_FW_TX_NOTIF_FRAME	GENMASK(12, 10)
+#define HAL_WBM_RELEASE_TX_INFO2_BUFFER_TIMESTAMP	GENMASK(31, 13)
+
+#define HAL_WBM_RELEASE_TX_INFO3_PEER_ID		GENMASK(15, 0)
+#define HAL_WBM_RELEASE_TX_INFO3_TID			GENMASK(19, 16)
+#define HAL_WBM_RELEASE_TX_INFO3_SW_BUFFER_COOKIE_19_12	GENMASK(27, 20)
+#define HAL_WBM_RELEASE_TX_INFO3_LOOPING_COUNT		GENMASK(31, 28)
+
+struct hal_wbm_release_ring_tx {
+	struct ath12k_buffer_addr buf_addr_info;
+	__le32 info0;
+	__le32 info1;
+	__le32 info2;
+	struct hal_tx_rate_stats rate_stats;
+	__le32 info3;
+} __packed;
+
+#define HAL_WBM_RELEASE_RX_INFO0_REL_SRC_MODULE		GENMASK(2, 0)
+#define HAL_WBM_RELEASE_RX_INFO0_BM_ACTION		GENMASK(5, 3)
+#define HAL_WBM_RELEASE_RX_INFO0_DESC_TYPE		GENMASK(8, 6)
+#define HAL_WBM_RELEASE_RX_INFO0_FIRST_MSDU_IDX		GENMASK(12, 9)
+#define HAL_WBM_RELEASE_RX_INFO0_CC_STATUS		BIT(16)
+#define HAL_WBM_RELEASE_RX_INFO0_RXDMA_PUSH_REASON	GENMASK(18, 17)
+#define HAL_WBM_RELEASE_RX_INFO0_RXDMA_ERROR_CODE	GENMASK(23, 19)
+#define HAL_WBM_RELEASE_RX_INFO0_REO_PUSH_REASON	GENMASK(25, 24)
+#define HAL_WBM_RELEASE_RX_INFO0_REO_ERROR_CODE		GENMASK(30, 26)
+#define HAL_WBM_RELEASE_RX_INFO0_WBM_INTERNAL_ERROR	BIT(31)
+
+#define HAL_WBM_RELEASE_RX_INFO2_RING_ID		GENMASK(27, 20)
+#define HAL_WBM_RELEASE_RX_INFO2_LOOPING_COUNT		GENMASK(31, 28)
+
+struct hal_wbm_release_ring_rx {
+	struct ath12k_buffer_addr buf_addr_info;
+	__le32 info0;
+	struct rx_mpdu_desc rx_mpdu_info;
+	struct rx_msdu_desc rx_msdu_info;
+	__le32 info1;
+	__le32 info2;
+} __packed;
+
+#define HAL_WBM_RELEASE_RX_CC_INFO0_RBM			GENMASK(12, 9)
+#define HAL_WBM_RELEASE_RX_CC_INFO1_COOKIE		GENMASK(27, 8)
+/* Used when hw cc is success */
+struct hal_wbm_release_ring_cc_rx {
+	__le32 buf_va_lo;
+	__le32 buf_va_hi;
+	__le32 info0;
+	struct rx_mpdu_desc rx_mpdu_info;
+	struct rx_msdu_desc rx_msdu_info;
+	__le32 buf_pa_lo;
+	__le32 info1;
+} __packed;
+
+#define HAL_WBM_RELEASE_INFO0_REL_SRC_MODULE		GENMASK(2, 0)
+#define HAL_WBM_RELEASE_INFO0_BM_ACTION			GENMASK(5, 3)
+#define HAL_WBM_RELEASE_INFO0_DESC_TYPE			GENMASK(8, 6)
+#define HAL_WBM_RELEASE_INFO0_RXDMA_PUSH_REASON		GENMASK(18, 17)
+#define HAL_WBM_RELEASE_INFO0_RXDMA_ERROR_CODE		GENMASK(23, 19)
+#define HAL_WBM_RELEASE_INFO0_REO_PUSH_REASON		GENMASK(25, 24)
+#define HAL_WBM_RELEASE_INFO0_REO_ERROR_CODE		GENMASK(30, 26)
+#define HAL_WBM_RELEASE_INFO0_WBM_INTERNAL_ERROR	BIT(31)
+
+#define HAL_WBM_RELEASE_INFO3_FIRST_MSDU		BIT(0)
+#define HAL_WBM_RELEASE_INFO3_LAST_MSDU			BIT(1)
+#define HAL_WBM_RELEASE_INFO3_CONTINUATION		BIT(2)
+
+#define HAL_WBM_RELEASE_INFO5_LOOPING_COUNT		GENMASK(31, 28)
+
+struct hal_wbm_release_ring {
+	struct ath12k_buffer_addr buf_addr_info;
+	__le32 info0;
+	__le32 info1;
+	__le32 info2;
+	__le32 info3;
+	__le32 info4;
+	__le32 info5;
+} __packed;
+
+/* hal_wbm_release_ring
+ *
+ *	Producer: SW/TQM/RXDMA/REO/SWITCH
+ *	Consumer: WBM/SW/FW
+ *
+ * HTT tx status is overlayed on wbm_release ring on 4-byte words 2, 3, 4 and 5
+ * for software based completions.
+ *
+ * buf_addr_info
+ *	Details of the physical address of the buffer or link descriptor.
+ *
+ * release_source_module
+ *	Indicates which module initiated the release of this buffer/descriptor.
+ *	Values are defined in enum %HAL_WBM_REL_SRC_MODULE_.
+ *
+ * buffer_or_desc_type
+ *	Field only valid when WBM is marked as the return_buffer_manager in
+ *	the Released_Buffer_address_info. Indicates that type of buffer or
+ *	descriptor is being released. Values are in enum %HAL_WBM_REL_DESC_TYPE.
+ *
+ * wbm_internal_error
+ *	Is set when WBM got a buffer pointer but the action was to push it to
+ *	the idle link descriptor ring or do link related activity OR
+ *	Is set when WBM got a link buffer pointer but the action was to push it
+ *	to the buffer descriptor ring.
+ *
+ * looping_count
+ *	A count value that indicates the number of times the
+ *	producer of entries into the Buffer Manager Ring has looped
+ *	around the ring.
+ *
+ *	At initialization time, this value is set to 0. On the
+ *	first loop, this value is set to 1. After the max value is
+ *	reached allowed by the number of bits for this field, the
+ *	count value continues with 0 again.
+ *
+ *	In case SW is the consumer of the ring entries, it can
+ *	use this field to figure out up to where the producer of
+ *	entries has created new entries. This eliminates the need to
+ *	check where the head pointer' of the ring is located once
+ *	the SW starts processing an interrupt indicating that new
+ *	entries have been put into this ring...
+ *
+ *	Also note that SW if it wants only needs to look at the
+ *	LSB bit of this count value.
+ */
+
+/**
+ * enum hal_wbm_tqm_rel_reason - TQM release reason code
+ * @HAL_WBM_TQM_REL_REASON_FRAME_ACKED: ACK or BACK received for the frame
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_MPDU: Command remove_mpdus initiated by SW
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_TX: Command remove transmitted_mpdus
+ *	initiated by sw.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_NOTX: Command remove untransmitted_mpdus
+ *	initiated by sw.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_AGED_FRAMES: Command remove aged msdus or
+ *	mpdus.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON1: Remove command initiated by
+ *	fw with fw_reason1.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON2: Remove command initiated by
+ *	fw with fw_reason2.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON3: Remove command initiated by
+ *	fw with fw_reason3.
+ */
+enum hal_wbm_tqm_rel_reason {
+	HAL_WBM_TQM_REL_REASON_FRAME_ACKED,
+	HAL_WBM_TQM_REL_REASON_CMD_REMOVE_MPDU,
+	HAL_WBM_TQM_REL_REASON_CMD_REMOVE_TX,
+	HAL_WBM_TQM_REL_REASON_CMD_REMOVE_NOTX,
+	HAL_WBM_TQM_REL_REASON_CMD_REMOVE_AGED_FRAMES,
+	HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON1,
+	HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON2,
+	HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON3,
+};
+
+struct hal_wbm_buffer_ring {
+	struct ath12k_buffer_addr buf_addr_info;
+};
+
+enum hal_mon_end_reason {
+	HAL_MON_STATUS_BUFFER_FULL,
+	HAL_MON_FLUSH_DETECTED,
+	HAL_MON_END_OF_PPDU,
+	HAL_MON_PPDU_TRUNCATED,
+};
+
+#define HAL_SW_MONITOR_RING_INFO0_RXDMA_PUSH_REASON	GENMASK(1, 0)
+#define HAL_SW_MONITOR_RING_INFO0_RXDMA_ERROR_CODE	GENMASK(6, 2)
+#define HAL_SW_MONITOR_RING_INFO0_MPDU_FRAGMENT_NUMBER	GENMASK(10, 7)
+#define HAL_SW_MONITOR_RING_INFO0_FRAMELESS_BAR		BIT(11)
+#define HAL_SW_MONITOR_RING_INFO0_STATUS_BUF_COUNT	GENMASK(15, 12)
+#define HAL_SW_MONITOR_RING_INFO0_END_OF_PPDU		BIT(16)
+
+#define HAL_SW_MONITOR_RING_INFO1_PHY_PPDU_ID	GENMASK(15, 0)
+#define HAL_SW_MONITOR_RING_INFO1_RING_ID	GENMASK(27, 20)
+#define HAL_SW_MONITOR_RING_INFO1_LOOPING_COUNT	GENMASK(31, 28)
+
+struct hal_sw_monitor_ring {
+	struct ath12k_buffer_addr buf_addr_info;
+	struct rx_mpdu_desc rx_mpdu_info;
+	struct ath12k_buffer_addr status_buff_addr_info;
+	__le32 info0; /* %HAL_SW_MONITOR_RING_INFO0 */
+	__le32 info1; /* %HAL_SW_MONITOR_RING_INFO1 */
+} __packed;
+
+/* hal_sw_monitor_ring
+ *
+ *		Producer: RXDMA
+ *		Consumer: REO/SW/FW
+ * buf_addr_info
+ *              Details of the physical address of a buffer or MSDU
+ *              link descriptor.
+ *
+ * rx_mpdu_info
+ *              Details related to the MPDU being pushed to SW, valid
+ *              only if end_of_ppdu is set to 0.
+ *
+ * status_buff_addr_info
+ *		Details of the physical address of the first status
+ *		buffer used for the PPDU (either the PPDU that included the
+ *		MPDU being pushed to SW if end_of_ppdu = 0, or the PPDU
+ *		whose end is indicated through end_of_ppdu = 1)
+ *
+ * rxdma_push_reason
+ *		Indicates why RXDMA pushed the frame to this ring
+ *
+ *		<enum 0 rxdma_error_detected> RXDMA detected an error an
+ *		pushed this frame to this queue
+ *
+ *		<enum 1 rxdma_routing_instruction> RXDMA pushed the
+ *		frame to this queue per received routing instructions. No
+ *		error within RXDMA was detected
+ *
+ *		<enum 2 rxdma_rx_flush> RXDMA received an RX_FLUSH. As a
+ *		result the MSDU link descriptor might not have the
+ *		last_msdu_in_mpdu_flag set, but instead WBM might just see a
+ *		NULL pointer in the MSDU link descriptor. This is to be
+ *		considered a normal condition for this scenario.
+ *
+ * rxdma_error_code
+ *		Field only valid when rxdma_push_reason is set to
+ *		'rxdma_error_detected.'
+ *
+ *		<enum 0 rxdma_overflow_err>MPDU frame is not complete
+ *		due to a FIFO overflow error in RXPCU.
+ *
+ *		<enum 1 rxdma_mpdu_length_err>MPDU frame is not complete
+ *		due to receiving incomplete MPDU from the PHY
+ *
+ *		<enum 3 rxdma_decrypt_err>CRYPTO reported a decryption
+ *		error or CRYPTO received an encrypted frame, but did not get
+ *		a valid corresponding key id in the peer entry.
+ *
+ *		<enum 4 rxdma_tkip_mic_err>CRYPTO reported a TKIP MIC
+ *		error
+ *
+ *		<enum 5 rxdma_unecrypted_err>CRYPTO reported an
+ *		unencrypted frame error when encrypted was expected
+ *
+ *		<enum 6 rxdma_msdu_len_err>RX OLE reported an MSDU
+ *		length error
+ *
+ *		<enum 7 rxdma_msdu_limit_err>RX OLE reported that max
+ *		number of MSDUs allowed in an MPDU got exceeded
+ *
+ *		<enum 8 rxdma_wifi_parse_err>RX OLE reported a parsing
+ *		error
+ *
+ *		<enum 9 rxdma_amsdu_parse_err>RX OLE reported an A-MSDU
+ *		parsing error
+ *
+ *		<enum 10 rxdma_sa_timeout_err>RX OLE reported a timeout
+ *		during SA search
+ *
+ *		<enum 11 rxdma_da_timeout_err>RX OLE reported a timeout
+ *		during DA search
+ *
+ *		<enum 12 rxdma_flow_timeout_err>RX OLE reported a
+ *		timeout during flow search
+ *
+ *		<enum 13 rxdma_flush_request>RXDMA received a flush
+ *		request
+ *
+ *		<enum 14 rxdma_amsdu_fragment_err>Rx PCU reported A-MSDU
+ *		present as well as a fragmented MPDU.
+ *
+ * mpdu_fragment_number
+ *		Field only valid when Reo_level_mpdu_frame_info.
+ *		Rx_mpdu_desc_info_details.Fragment_flag is set and
+ *		end_of_ppdu is set to 0.
+ *
+ *		The fragment number from the 802.11 header.
+ *
+ *		Note that the sequence number is embedded in the field:
+ *		Reo_level_mpdu_frame_info. Rx_mpdu_desc_info_details.
+ *		Mpdu_sequence_number
+ *
+ * frameless_bar
+ *		When set, this SW monitor ring struct contains BAR info
+ *		from a multi TID BAR frame. The original multi TID BAR frame
+ *		itself contained all the REO info for the first TID, but all
+ *		the subsequent TID info and their linkage to the REO
+ *		descriptors is passed down as 'frameless' BAR info.
+ *
+ *		The only fields valid in this descriptor when this bit
+ *		is within the
+ *
+ *		Reo_level_mpdu_frame_info:
+ *		   Within Rx_mpdu_desc_info_details:
+ *			Mpdu_Sequence_number
+ *			BAR_frame
+ *			Peer_meta_data
+ *			All other fields shall be set to 0.
+ *
+ * status_buf_count
+ *		A count of status buffers used so far for the PPDU
+ *		(either the PPDU that included the MPDU being pushed to SW
+ *		if end_of_ppdu = 0, or the PPDU whose end is indicated
+ *		through end_of_ppdu = 1)
+ *
+ * end_of_ppdu
+ *		Some hw RXDMA can be configured to generate a separate
+ *		'SW_MONITOR_RING' descriptor at the end of a PPDU (either
+ *		through an 'RX_PPDU_END' TLV or through an 'RX_FLUSH') to
+ *		demarcate PPDUs.
+ *
+ *		For such a descriptor, this bit is set to 1 and fields
+ *		Reo_level_mpdu_frame_info, mpdu_fragment_number and
+ *		Frameless_bar are all set to 0.
+ *
+ *		Otherwise this bit is set to 0.
+ *
+ * phy_ppdu_id
+ *		A PPDU counter value that PHY increments for every PPDU
+ *		received
+ *
+ *		The counter value wraps around. Some hw RXDMA can be
+ *		configured to copy this from the RX_PPDU_START TLV for every
+ *		output descriptor.
+ *
+ * ring_id
+ *		For debugging.
+ *		This field is filled in by the SRNG module.
+ *		It help to identify the ring that is being looked
+ *
+ * looping_count
+ *		For debugging.
+ *		This field is filled in by the SRNG module.
+ *
+ *		A count value that indicates the number of times the
+ *		producer of entries into this Ring has looped around the
+ *		ring.
+ *		At initialization time, this value is set to 0. On the
+ *		first loop, this value is set to 1. After the max value is
+ *		reached allowed by the number of bits for this field, the
+ *		count value continues with 0 again.
+ *
+ *		In case SW is the consumer of the ring entries, it can
+ *		use this field to figure out up to where the producer of
+ *		entries has created new entries. This eliminates the need to
+ *		check where the head pointer' of the ring is located once
+ *		the SW starts processing an interrupt indicating that new
+ *		entries have been put into this ring...
+ */
+
+enum hal_desc_owner {
+	HAL_DESC_OWNER_WBM,
+	HAL_DESC_OWNER_SW,
+	HAL_DESC_OWNER_TQM,
+	HAL_DESC_OWNER_RXDMA,
+	HAL_DESC_OWNER_REO,
+	HAL_DESC_OWNER_SWITCH,
+};
+
+enum hal_desc_buf_type {
+	HAL_DESC_BUF_TYPE_TX_MSDU_LINK,
+	HAL_DESC_BUF_TYPE_TX_MPDU_LINK,
+	HAL_DESC_BUF_TYPE_TX_MPDU_QUEUE_HEAD,
+	HAL_DESC_BUF_TYPE_TX_MPDU_QUEUE_EXT,
+	HAL_DESC_BUF_TYPE_TX_FLOW,
+	HAL_DESC_BUF_TYPE_TX_BUFFER,
+	HAL_DESC_BUF_TYPE_RX_MSDU_LINK,
+	HAL_DESC_BUF_TYPE_RX_MPDU_LINK,
+	HAL_DESC_BUF_TYPE_RX_REO_QUEUE,
+	HAL_DESC_BUF_TYPE_RX_REO_QUEUE_EXT,
+	HAL_DESC_BUF_TYPE_RX_BUFFER,
+	HAL_DESC_BUF_TYPE_IDLE_LINK,
+};
+
+#define HAL_DESC_REO_OWNED		4
+#define HAL_DESC_REO_QUEUE_DESC		8
+#define HAL_DESC_REO_QUEUE_EXT_DESC	9
+#define HAL_DESC_REO_NON_QOS_TID	16
+
+#define HAL_DESC_HDR_INFO0_OWNER	GENMASK(3, 0)
+#define HAL_DESC_HDR_INFO0_BUF_TYPE	GENMASK(7, 4)
+#define HAL_DESC_HDR_INFO0_DBG_RESERVED	GENMASK(31, 8)
+
+struct hal_desc_header {
+	__le32 info0;
+} __packed;
+
+struct hal_rx_mpdu_link_ptr {
+	struct ath12k_buffer_addr addr_info;
+} __packed;
+
+struct hal_rx_msdu_details {
+	struct ath12k_buffer_addr buf_addr_info;
+	struct rx_msdu_desc rx_msdu_info;
+	struct rx_msdu_ext_desc rx_msdu_ext_info;
+} __packed;
+
+#define HAL_RX_MSDU_LNK_INFO0_RX_QUEUE_NUMBER		GENMASK(15, 0)
+#define HAL_RX_MSDU_LNK_INFO0_FIRST_MSDU_LNK		BIT(16)
+
+struct hal_rx_msdu_link {
+	struct hal_desc_header desc_hdr;
+	struct ath12k_buffer_addr buf_addr_info;
+	__le32 info0;
+	__le32 pn[4];
+	struct hal_rx_msdu_details msdu_link[6];
+} __packed;
+
+struct hal_rx_reo_queue_ext {
+	struct hal_desc_header desc_hdr;
+	__le32 rsvd;
+	struct hal_rx_mpdu_link_ptr mpdu_link[15];
+} __packed;
+
+/* hal_rx_reo_queue_ext
+ *	Consumer: REO
+ *	Producer: REO
+ *
+ * descriptor_header
+ *	Details about which module owns this struct.
+ *
+ * mpdu_link
+ *	Pointer to the next MPDU_link descriptor in the MPDU queue.
+ */
+
+enum hal_rx_reo_queue_pn_size {
+	HAL_RX_REO_QUEUE_PN_SIZE_24,
+	HAL_RX_REO_QUEUE_PN_SIZE_48,
+	HAL_RX_REO_QUEUE_PN_SIZE_128,
+};
+
+#define HAL_RX_REO_QUEUE_RX_QUEUE_NUMBER		GENMASK(15, 0)
+
+#define HAL_RX_REO_QUEUE_INFO0_VLD			BIT(0)
+#define HAL_RX_REO_QUEUE_INFO0_ASSOC_LNK_DESC_COUNTER	GENMASK(2, 1)
+#define HAL_RX_REO_QUEUE_INFO0_DIS_DUP_DETECTION	BIT(3)
+#define HAL_RX_REO_QUEUE_INFO0_SOFT_REORDER_EN		BIT(4)
+#define HAL_RX_REO_QUEUE_INFO0_AC			GENMASK(6, 5)
+#define HAL_RX_REO_QUEUE_INFO0_BAR			BIT(7)
+#define HAL_RX_REO_QUEUE_INFO0_RETRY			BIT(8)
+#define HAL_RX_REO_QUEUE_INFO0_CHECK_2K_MODE		BIT(9)
+#define HAL_RX_REO_QUEUE_INFO0_OOR_MODE			BIT(10)
+#define HAL_RX_REO_QUEUE_INFO0_BA_WINDOW_SIZE		GENMASK(20, 11)
+#define HAL_RX_REO_QUEUE_INFO0_PN_CHECK			BIT(21)
+#define HAL_RX_REO_QUEUE_INFO0_EVEN_PN			BIT(22)
+#define HAL_RX_REO_QUEUE_INFO0_UNEVEN_PN		BIT(23)
+#define HAL_RX_REO_QUEUE_INFO0_PN_HANDLE_ENABLE		BIT(24)
+#define HAL_RX_REO_QUEUE_INFO0_PN_SIZE			GENMASK(26, 25)
+#define HAL_RX_REO_QUEUE_INFO0_IGNORE_AMPDU_FLG		BIT(27)
+
+#define HAL_RX_REO_QUEUE_INFO1_SVLD			BIT(0)
+#define HAL_RX_REO_QUEUE_INFO1_SSN			GENMASK(12, 1)
+#define HAL_RX_REO_QUEUE_INFO1_CURRENT_IDX		GENMASK(22, 13)
+#define HAL_RX_REO_QUEUE_INFO1_SEQ_2K_ERR		BIT(23)
+#define HAL_RX_REO_QUEUE_INFO1_PN_ERR			BIT(24)
+#define HAL_RX_REO_QUEUE_INFO1_PN_VALID			BIT(31)
+
+#define HAL_RX_REO_QUEUE_INFO2_MPDU_COUNT		GENMASK(6, 0)
+#define HAL_RX_REO_QUEUE_INFO2_MSDU_COUNT		(31, 7)
+
+#define HAL_RX_REO_QUEUE_INFO3_TIMEOUT_COUNT		GENMASK(9, 4)
+#define HAL_RX_REO_QUEUE_INFO3_FWD_DUE_TO_BAR_CNT	GENMASK(15, 10)
+#define HAL_RX_REO_QUEUE_INFO3_DUPLICATE_COUNT		GENMASK(31, 16)
+
+#define HAL_RX_REO_QUEUE_INFO4_FRAME_IN_ORD_COUNT	GENMASK(23, 0)
+#define HAL_RX_REO_QUEUE_INFO4_BAR_RECVD_COUNT		GENMASK(31, 24)
+
+#define HAL_RX_REO_QUEUE_INFO5_LATE_RX_MPDU_COUNT	GENMASK(11, 0)
+#define HAL_RX_REO_QUEUE_INFO5_WINDOW_JUMP_2K		GENMASK(15, 12)
+#define HAL_RX_REO_QUEUE_INFO5_HOLE_COUNT		GENMASK(31, 16)
+
+struct hal_rx_reo_queue {
+	struct hal_desc_header desc_hdr;
+	__le32 rx_queue_num;
+	__le32 info0;
+	__le32 info1;
+	__le32 pn[4];
+	__le32 last_rx_enqueue_timestamp;
+	__le32 last_rx_dequeue_timestamp;
+	__le32 next_aging_queue[2];
+	__le32 prev_aging_queue[2];
+	__le32 rx_bitmap[9];
+	__le32 info2;
+	__le32 info3;
+	__le32 info4;
+	__le32 processed_mpdus;
+	__le32 processed_msdus;
+	__le32 processed_total_bytes;
+	__le32 info5;
+	__le32 rsvd[2];
+	struct hal_rx_reo_queue_ext ext_desc[];
+} __packed;
+
+/* hal_rx_reo_queue
+ *
+ * descriptor_header
+ *	Details about which module owns this struct. Note that sub field
+ *	Buffer_type shall be set to receive_reo_queue_descriptor.
+ *
+ * receive_queue_number
+ *	Indicates the MPDU queue ID to which this MPDU link descriptor belongs.
+ *
+ * vld
+ *	Valid bit indicating a session is established and the queue descriptor
+ *	is valid.
+ * associated_link_descriptor_counter
+ *	Indicates which of the 3 link descriptor counters shall be incremented
+ *	or decremented when link descriptors are added or removed from this
+ *	flow queue.
+ * disable_duplicate_detection
+ *	When set, do not perform any duplicate detection.
+ * soft_reorder_enable
+ *	When set, REO has been instructed to not perform the actual re-ordering
+ *	of frames for this queue, but just to insert the reorder opcodes.
+ * ac
+ *	Indicates the access category of the queue descriptor.
+ * bar
+ *	Indicates if BAR has been received.
+ * retry
+ *	Retry bit is checked if this bit is set.
+ * chk_2k_mode
+ *	Indicates what type of operation is expected from Reo when the received
+ *	frame SN falls within the 2K window.
+ * oor_mode
+ *	Indicates what type of operation is expected when the received frame
+ *	falls within the OOR window.
+ * ba_window_size
+ *	Indicates the negotiated (window size + 1). Max of 256 bits.
+ *
+ *	A value 255 means 256 bitmap, 63 means 64 bitmap, 0 (means non-BA
+ *	session, with window size of 0). The 3 values here are the main values
+ *	validated, but other values should work as well.
+ *
+ *	A BA window size of 0 (=> one frame entry bitmat), means that there is
+ *	no additional rx_reo_queue_ext desc. following rx_reo_queue in memory.
+ *	A BA window size of 1 - 105, means that there is 1 rx_reo_queue_ext.
+ *	A BA window size of 106 - 210, means that there are 2 rx_reo_queue_ext.
+ *	A BA window size of 211 - 256, means that there are 3 rx_reo_queue_ext.
+ * pn_check_needed, pn_shall_be_even, pn_shall_be_uneven, pn_handling_enable,
+ * pn_size
+ *	REO shall perform the PN increment check, even number check, uneven
+ *	number check, PN error check and size of the PN field check.
+ * ignore_ampdu_flag
+ *	REO shall ignore the ampdu_flag on entrance descriptor for this queue.
+ *
+ * svld
+ *	Sequence number in next field is valid one.
+ * ssn
+ *	 Starting Sequence number of the session.
+ * current_index
+ *	Points to last forwarded packet
+ * seq_2k_error_detected_flag
+ *	REO has detected a 2k error jump in the sequence number and from that
+ *	moment forward, all new frames are forwarded directly to FW, without
+ *	duplicate detect, reordering, etc.
+ * pn_error_detected_flag
+ *	REO has detected a PN error.
+ */
+
+#define HAL_REO_UPD_RX_QUEUE_INFO0_QUEUE_ADDR_HI		GENMASK(7, 0)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_RX_QUEUE_NUM		BIT(8)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_VLD			BIT(9)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_ASSOC_LNK_DESC_CNT	BIT(10)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_DIS_DUP_DETECTION	BIT(11)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_SOFT_REORDER_EN		BIT(12)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_AC			BIT(13)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_BAR			BIT(14)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_RETRY			BIT(15)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_CHECK_2K_MODE		BIT(16)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_OOR_MODE			BIT(17)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_BA_WINDOW_SIZE		BIT(18)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_CHECK			BIT(19)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_EVEN_PN			BIT(20)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_UNEVEN_PN		BIT(21)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_HANDLE_ENABLE		BIT(22)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_SIZE			BIT(23)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_IGNORE_AMPDU_FLG		BIT(24)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_SVLD			BIT(25)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_SSN			BIT(26)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_SEQ_2K_ERR		BIT(27)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_ERR			BIT(28)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_VALID			BIT(29)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN			BIT(30)
+
+#define HAL_REO_UPD_RX_QUEUE_INFO1_RX_QUEUE_NUMBER		GENMASK(15, 0)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_VLD				BIT(16)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_ASSOC_LNK_DESC_COUNTER	GENMASK(18, 17)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_DIS_DUP_DETECTION		BIT(19)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_SOFT_REORDER_EN		BIT(20)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_AC				GENMASK(22, 21)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_BAR				BIT(23)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_RETRY			BIT(24)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_CHECK_2K_MODE		BIT(25)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_OOR_MODE			BIT(26)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_PN_CHECK			BIT(27)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_EVEN_PN			BIT(28)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_UNEVEN_PN			BIT(29)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_PN_HANDLE_ENABLE		BIT(30)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_IGNORE_AMPDU_FLG		BIT(31)
+
+#define HAL_REO_UPD_RX_QUEUE_INFO2_BA_WINDOW_SIZE		GENMASK(7, 0)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_PN_SIZE			GENMASK(9, 8)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_SVLD				BIT(10)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_SSN				GENMASK(22, 11)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_SEQ_2K_ERR			BIT(23)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_PN_ERR			BIT(24)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_PN_VALID			BIT(25)
+
+struct hal_reo_update_rx_queue {
+	struct hal_reo_cmd_hdr cmd;
+	__le32 queue_addr_lo;
+	__le32 info0;
+	__le32 info1;
+	__le32 info2;
+	__le32 pn[4];
+} __packed;
+
+#define HAL_REO_UNBLOCK_CACHE_INFO0_UNBLK_CACHE		BIT(0)
+#define HAL_REO_UNBLOCK_CACHE_INFO0_RESOURCE_IDX	GENMASK(2, 1)
+
+struct hal_reo_unblock_cache {
+	struct hal_reo_cmd_hdr cmd;
+	__le32 info0;
+	__le32 rsvd[7];
+} __packed;
+
+enum hal_reo_exec_status {
+	HAL_REO_EXEC_STATUS_SUCCESS,
+	HAL_REO_EXEC_STATUS_BLOCKED,
+	HAL_REO_EXEC_STATUS_FAILED,
+	HAL_REO_EXEC_STATUS_RESOURCE_BLOCKED,
+};
+
+#define HAL_REO_STATUS_HDR_INFO0_STATUS_NUM	GENMASK(15, 0)
+#define HAL_REO_STATUS_HDR_INFO0_EXEC_TIME	GENMASK(25, 16)
+#define HAL_REO_STATUS_HDR_INFO0_EXEC_STATUS	GENMASK(27, 26)
+
+struct hal_reo_status_hdr {
+	__le32 info0;
+	__le32 timestamp;
+} __packed;
+
+/* hal_reo_status_hdr
+ *		Producer: REO
+ *		Consumer: SW
+ *
+ * status_num
+ *		The value in this field is equal to value of the reo command
+ *		number. This field helps to correlate the statuses with the REO
+ *		commands.
+ *
+ * execution_time (in us)
+ *		The amount of time REO took to excecute the command. Note that
+ *		this time does not include the duration of the command waiting
+ *		in the command ring, before the execution started.
+ *
+ * execution_status
+ *		Execution status of the command. Values are defined in
+ *		enum %HAL_REO_EXEC_STATUS_.
+ */
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO0_SSN		GENMASK(11, 0)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO0_CUR_IDX		GENMASK(21, 12)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO1_MPDU_COUNT		GENMASK(6, 0)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO1_MSDU_COUNT		GENMASK(31, 7)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO2_WINDOW_JMP2K	GENMASK(3, 0)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO2_TIMEOUT_COUNT	GENMASK(9, 4)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO2_FDTB_COUNT		GENMASK(15, 10)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO2_DUPLICATE_COUNT	GENMASK(31, 16)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO3_FIO_COUNT		GENMASK(23, 0)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO3_BAR_RCVD_CNT	GENMASK(31, 24)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO4_LATE_RX_MPDU	GENMASK(11, 0)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO4_HOLE_COUNT		GENMASK(27, 12)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO5_LOOPING_CNT	GENMASK(31, 28)
+
+struct hal_reo_get_queue_stats_status {
+	struct hal_reo_status_hdr hdr;
+	__le32 info0;
+	__le32 pn[4];
+	__le32 last_rx_enqueue_timestamp;
+	__le32 last_rx_dequeue_timestamp;
+	__le32 rx_bitmap[9];
+	__le32 info1;
+	__le32 info2;
+	__le32 info3;
+	__le32 num_mpdu_frames;
+	__le32 num_msdu_frames;
+	__le32 total_bytes;
+	__le32 info4;
+	__le32 info5;
+} __packed;
+
+/* hal_reo_get_queue_stats_status
+ *		Producer: REO
+ *		Consumer: SW
+ *
+ * status_hdr
+ *		Details that can link this status with the original command. It
+ *		also contains info on how long REO took to execute this command.
+ *
+ * ssn
+ *		Starting Sequence number of the session, this changes whenever
+ *		window moves (can be filled by SW then maintained by REO).
+ *
+ * current_index
+ *		Points to last forwarded packet.
+ *
+ * pn
+ *		Bits of the PN number.
+ *
+ * last_rx_enqueue_timestamp
+ * last_rx_dequeue_timestamp
+ *		Timestamp of arrival of the last MPDU for this queue and
+ *		Timestamp of forwarding an MPDU accordingly.
+ *
+ * rx_bitmap
+ *		When a bit is set, the corresponding frame is currently held
+ *		in the re-order queue. The bitmap  is Fully managed by HW.
+ *
+ * current_mpdu_count
+ * current_msdu_count
+ *		The number of MPDUs and MSDUs in the queue.
+ *
+ * timeout_count
+ *		The number of times REO started forwarding frames even though
+ *		there is a hole in the bitmap. Forwarding reason is timeout.
+ *
+ * forward_due_to_bar_count
+ *		The number of times REO started forwarding frames even though
+ *		there is a hole in the bitmap. Fwd reason is reception of BAR.
+ *
+ * duplicate_count
+ *		The number of duplicate frames that have been detected.
+ *
+ * frames_in_order_count
+ *		The number of frames that have been received in order (without
+ *		a hole that prevented them from being forwarded immediately).
+ *
+ * bar_received_count
+ *		The number of times a BAR frame is received.
+ *
+ * mpdu_frames_processed_count
+ * msdu_frames_processed_count
+ *		The total number of MPDU/MSDU frames that have been processed.
+ *
+ * total_bytes
+ *		An approximation of the number of bytes received for this queue.
+ *
+ * late_receive_mpdu_count
+ *		The number of MPDUs received after the window had already moved
+ *		on. The 'late' sequence window is defined as
+ *		(Window SSN - 256) - (Window SSN - 1).
+ *
+ * window_jump_2k
+ *		The number of times the window moved more than 2K
+ *
+ * hole_count
+ *		The number of times a hole was created in the receive bitmap.
+ *
+ * looping_count
+ *		A count value that indicates the number of times the producer of
+ *		entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_STATUS_LOOP_CNT			GENMASK(31, 28)
+
+#define HAL_REO_FLUSH_QUEUE_INFO0_ERR_DETECTED	BIT(0)
+#define HAL_REO_FLUSH_QUEUE_INFO0_RSVD		GENMASK(31, 1)
+#define HAL_REO_FLUSH_QUEUE_INFO1_RSVD		GENMASK(27, 0)
+
+struct hal_reo_flush_queue_status {
+	struct hal_reo_status_hdr hdr;
+	__le32 info0;
+	__le32 rsvd0[21];
+	__le32 info1;
+} __packed;
+
+/* hal_reo_flush_queue_status
+ *		Producer: REO
+ *		Consumer: SW
+ *
+ * status_hdr
+ *		Details that can link this status with the original command. It
+ *		also contains info on how long REO took to execute this command.
+ *
+ * error_detected
+ *		Status of blocking resource
+ *
+ *		0 - No error has been detected while executing this command
+ *		1 - Error detected. The resource to be used for blocking was
+ *		    already in use.
+ *
+ * looping_count
+ *		A count value that indicates the number of times the producer of
+ *		entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_IS_ERR			BIT(0)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_BLOCK_ERR_CODE		GENMASK(2, 1)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_STATUS_HIT	BIT(8)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_DESC_TYPE	GENMASK(11, 9)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_CLIENT_ID	GENMASK(15, 12)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_ERR		GENMASK(17, 16)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_COUNT		GENMASK(25, 18)
+
+struct hal_reo_flush_cache_status {
+	struct hal_reo_status_hdr hdr;
+	__le32 info0;
+	__le32 rsvd0[21];
+	__le32 info1;
+} __packed;
+
+/* hal_reo_flush_cache_status
+ *		Producer: REO
+ *		Consumer: SW
+ *
+ * status_hdr
+ *		Details that can link this status with the original command. It
+ *		also contains info on how long REO took to execute this command.
+ *
+ * error_detected
+ *		Status for blocking resource handling
+ *
+ *		0 - No error has been detected while executing this command
+ *		1 - An error in the blocking resource management was detected
+ *
+ * block_error_details
+ *		only valid when error_detected is set
+ *
+ *		0 - No blocking related errors found
+ *		1 - Blocking resource is already in use
+ *		2 - Resource requested to be unblocked, was not blocked
+ *
+ * cache_controller_flush_status_hit
+ *		The status that the cache controller returned on executing the
+ *		flush command.
+ *
+ *		0 - miss; 1 - hit
+ *
+ * cache_controller_flush_status_desc_type
+ *		Flush descriptor type
+ *
+ * cache_controller_flush_status_client_id
+ *		Module who made the flush request
+ *
+ *		In REO, this is always 0
+ *
+ * cache_controller_flush_status_error
+ *		Error condition
+ *
+ *		0 - No error found
+ *		1 - HW interface is still busy
+ *		2 - Line currently locked. Used for one line flush command
+ *		3 - At least one line is still locked.
+ *		    Used for cache flush command.
+ *
+ * cache_controller_flush_count
+ *		The number of lines that were actually flushed out
+ *
+ * looping_count
+ *		A count value that indicates the number of times the producer of
+ *		entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_UNBLOCK_CACHE_STATUS_INFO0_IS_ERR	BIT(0)
+#define HAL_REO_UNBLOCK_CACHE_STATUS_INFO0_TYPE		BIT(1)
+
+struct hal_reo_unblock_cache_status {
+	struct hal_reo_status_hdr hdr;
+	__le32 info0;
+	__le32 rsvd0[21];
+	__le32 info1;
+} __packed;
+
+/* hal_reo_unblock_cache_status
+ *		Producer: REO
+ *		Consumer: SW
+ *
+ * status_hdr
+ *		Details that can link this status with the original command. It
+ *		also contains info on how long REO took to execute this command.
+ *
+ * error_detected
+ *		0 - No error has been detected while executing this command
+ *		1 - The blocking resource was not in use, and therefore it could
+ *		    not be unblocked.
+ *
+ * unblock_type
+ *		Reference to the type of unblock command
+ *		0 - Unblock a blocking resource
+ *		1 - The entire cache usage is unblock
+ *
+ * looping_count
+ *		A count value that indicates the number of times the producer of
+ *		entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_FLUSH_TIMEOUT_STATUS_INFO0_IS_ERR		BIT(0)
+#define HAL_REO_FLUSH_TIMEOUT_STATUS_INFO0_LIST_EMPTY		BIT(1)
+
+#define HAL_REO_FLUSH_TIMEOUT_STATUS_INFO1_REL_DESC_COUNT	GENMASK(15, 0)
+#define HAL_REO_FLUSH_TIMEOUT_STATUS_INFO1_FWD_BUF_COUNT	GENMASK(31, 16)
+
+struct hal_reo_flush_timeout_list_status {
+	struct hal_reo_status_hdr hdr;
+	__le32 info0;
+	__le32 info1;
+	__le32 rsvd0[20];
+	__le32 info2;
+} __packed;
+
+/* hal_reo_flush_timeout_list_status
+ *		Producer: REO
+ *		Consumer: SW
+ *
+ * status_hdr
+ *		Details that can link this status with the original command. It
+ *		also contains info on how long REO took to execute this command.
+ *
+ * error_detected
+ *		0 - No error has been detected while executing this command
+ *		1 - Command not properly executed and returned with error
+ *
+ * timeout_list_empty
+ *		When set, REO has depleted the timeout list and all entries are
+ *		gone.
+ *
+ * release_desc_count
+ *		Producer: SW; Consumer: REO
+ *		The number of link descriptor released
+ *
+ * forward_buf_count
+ *		Producer: SW; Consumer: REO
+ *		The number of buffers forwarded to the REO destination rings
+ *
+ * looping_count
+ *		A count value that indicates the number of times the producer of
+ *		entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_DESC_THRESH_STATUS_INFO0_THRESH_INDEX		GENMASK(1, 0)
+#define HAL_REO_DESC_THRESH_STATUS_INFO1_LINK_DESC_COUNTER0	GENMASK(23, 0)
+#define HAL_REO_DESC_THRESH_STATUS_INFO2_LINK_DESC_COUNTER1	GENMASK(23, 0)
+#define HAL_REO_DESC_THRESH_STATUS_INFO3_LINK_DESC_COUNTER2	GENMASK(23, 0)
+#define HAL_REO_DESC_THRESH_STATUS_INFO4_LINK_DESC_COUNTER_SUM	GENMASK(25, 0)
+
+struct hal_reo_desc_thresh_reached_status {
+	struct hal_reo_status_hdr hdr;
+	__le32 info0;
+	__le32 info1;
+	__le32 info2;
+	__le32 info3;
+	__le32 info4;
+	__le32 rsvd0[17];
+	__le32 info5;
+} __packed;
+
+/* hal_reo_desc_thresh_reached_status
+ *		Producer: REO
+ *		Consumer: SW
+ *
+ * status_hdr
+ *		Details that can link this status with the original command. It
+ *		also contains info on how long REO took to execute this command.
+ *
+ * threshold_index
+ *		The index of the threshold register whose value got reached
+ *
+ * link_descriptor_counter0
+ * link_descriptor_counter1
+ * link_descriptor_counter2
+ * link_descriptor_counter_sum
+ *		Value of the respective counters at generation of this message
+ *
+ * looping_count
+ *		A count value that indicates the number of times the producer of
+ *		entries into this Ring has looped around the ring.
+ */
+
+#define HAL_TCL_ENTRANCE_FROM_PPE_RING_INFO0_DATA_LENGTH	GENMASK(13, 0)
+#define HAL_TCL_ENTRANCE_FROM_PPE_RING_INFO0_L4_CSUM_STATUS	BIT(14)
+#define HAL_TCL_ENTRANCE_FROM_PPE_RING_INFO0_L3_CSUM_STATUS	BIT(15)
+#define HAL_TCL_ENTRANCE_FROM_PPE_RING_INFO0_PID		GENMASK(27, 24)
+#define HAL_TCL_ENTRANCE_FROM_PPE_RING_INFO0_QDISC		BIT(28)
+#define HAL_TCL_ENTRANCE_FROM_PPE_RING_INFO0_MULTICAST	BIT(29)
+#define HAL_TCL_ENTRANCE_FROM_PPE_RING_INFO0_MORE		BIT(30)
+#define HAL_TCL_ENTRANCE_FROM_PPE_RING_INFO0_VALID_TOGGLE	BIT(31)
+
+struct hal_tcl_entrance_from_ppe_ring {
+	__le32 buffer_addr;
+	__le32 info0;
+} __packed;
+
+struct hal_mon_buf_ring {
+	__le32 paddr_lo;
+	__le32 paddr_hi;
+	__le64 cookie;
+};
+
+/* hal_mon_buf_ring
+ *	Producer : SW
+ *	Consumer : Monitor
+ *
+ * paddr_lo
+ *	Lower 32-bit physical address of the buffer pointer from the source ring.
+ * paddr_hi
+ *	bit range 7-0 : upper 8 bit of the physical address.
+ *	bit range 31-8 : reserved.
+ * cookie
+ *	Consumer: RxMon/TxMon 64 bit cookie of the buffers.
+ */
+
+#define HAL_MON_DEST_COOKIE_BUF_ID      GENMASK(17, 0)
+
+#define HAL_MON_DEST_INFO0_END_OFFSET		GENMASK(15, 0)
+#define HAL_MON_DEST_INFO0_FLUSH_DETECTED	BIT(16)
+#define HAL_MON_DEST_INFO0_END_OF_PPDU		BIT(17)
+#define HAL_MON_DEST_INFO0_INITIATOR		BIT(18)
+#define HAL_MON_DEST_INFO0_EMPTY_DESC		BIT(19)
+#define HAL_MON_DEST_INFO0_RING_ID		GENMASK(27, 20)
+#define HAL_MON_DEST_INFO0_LOOPING_COUNT	GENMASK(31, 28)
+
+struct hal_mon_dest_desc {
+	__le32 cookie;
+	__le32 reserved;
+	__le32 ppdu_id;
+	__le32 info0;
+};
+
+/* hal_mon_dest_ring
+ *	Producer : TxMon/RxMon
+ *	Consumer : SW
+ * cookie
+ *	bit 0 -17 buf_id to track the skb's vaddr.
+ * ppdu_id
+ *	Phy ppdu_id
+ * end_offset
+ *	The offset into status buffer where DMA ended, ie., offset to the last
+ *	TLV + last TLV size.
+ * flush_detected
+ *	Indicates whether 'tx_flush' or 'rx_flush' occurred.
+ * end_of_ppdu
+ *	Indicates end of ppdu.
+ * pmac_id
+ *	Indicates PMAC that received from frame.
+ * empty_descriptor
+ *	This descriptor is written on flush or end of ppdu or end of status
+ *	buffer.
+ * ring_id
+ *	updated by SRNG.
+ * looping_count
+ *	updated by SRNG.
+ */
+
+#endif /* ATH12K_HAL_DESC_H */




[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Wireless Regulations]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux