Manikanta Pubbisetty <quic_mpubbise@xxxxxxxxxxx> writes: > WCN6750 is non-DBS 2x2 11AX chipset. Unlike QCA6390/WCN6855 which > are DBS (dual band simultaneous) solutions (2 LMACs), WCN6750 has a > single LMAC supporting 2G, 5G and 6G bands. It can be operated only > on one band at any given point. > > WCN6750 is a PCIe device. Unlike other supported ATH11K PCIe devices > which are directly attached to APSS (Application Processor SubSystem), > WCN6750 is not attached to APSS, it is attached to the WPSS > (Wireless Processor SubSystem) Q6 processor, the FW which runs on the > Q6 processor will enumerate the PCIe device. Since APSS is unaware of > such a device, it has to be registered as a platform device(AHB) to the > kernel for device probing. Like other AHB devices, remoteproc APIs are > used to boot up or shutdown of WCN6750. > > WCN6750 uses both AHB and PCIe ATH11K APIs for it's operation. > It uses AHB APIs for device probe and booting of the remote processor. > Once device is booted up, it uses ATH11K PCIe APIs for initialization > and register access. Hence, it is referred as hybrid bus device in > the rest of this series. > > Since the chip is enumerated by WPSS Q6, device information like > BAR and BAR size is not known to the APSS processor. A new QMI message > called device info QMI request will be sent to the target for fetching > these details. > > STA and AP modes are supported; Basic connectivity and ping are > verified in both the modes. > > An important point to note is that though WCN6750 is a PCIe device, > it cannot be attached to any other platform except on Qualcomm > Snapdragon SoCs due to the aforementioned reasons. > > Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1 > Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 > Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 > Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 > > Manikanta Pubbisetty (12): > dt: bindings: net: add bindings of WCN6750 for ath11k > ath11k: Add HW params for WCN6750 > ath11k: Add bus params for WCN6750 > ath11k: Add register access logic for WCN6750 > ath11k: Fetch device information via QMI for WCN6750 > ath11k: Add QMI changes for WCN6750 > ath11k: HAL changes to support WCN6750 > ath11k: Datapath changes to support WCN6750 > ath11k: Do not put HW in DBS mode for WCN6750 > ath11k: WMI changes to support WCN6750 > ath11k: Update WBM idle ring HP after FW mode on > ath11k: Add support for WCN6750 device Due to the bus_params problem I had to drop most of the patches, but I did keep few of them in the pending branch to reduce the patchset size: 495a15b1969a ath11k: Update WBM idle ring HP after FW mode on 8d121dacbe35 ath11k: WMI changes to support WCN6750 e31091e06011 ath11k: Do not put HW in DBS mode for WCN6750 Please submit v6 only after I have applied these, I'm waiting for some build testing first. -- https://patchwork.kernel.org/project/linux-wireless/list/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
