Hi Lore, On Wed, 2022-03-16 at 16:15 +0100, Lorenzo Bianconi wrote: > > From: Deren Wu <deren.wu@xxxxxxxxxxxx> > > > > When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to > > fw for channel config. This would cause rx performance bad while > > monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would > > get the same performance as normal channels. > > Hi Deren, > > > > > Reviewed-by: Shayne Chen <shayne.chen@xxxxxxxxxxxx> > > Signed-off-by: Deren Wu <deren.wu@xxxxxxxxxxxx> > > --- > > drivers/net/wireless/mediatek/mt76/mt7615/mcu.c | 3 ++- > > drivers/net/wireless/mediatek/mt76/mt7915/mcu.c | 3 ++- > > drivers/net/wireless/mediatek/mt76/mt7921/mcu.c | 3 ++- > > 3 files changed, 6 insertions(+), 3 deletions(-) > > > > diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c > > b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c > > index 390add3144c2..97e2a85cb728 100644 > > --- a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c > > +++ b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c > > @@ -2151,7 +2151,8 @@ int mt7615_mcu_set_chan_info(struct > > mt7615_phy *phy, int cmd) > > .center_chan2 = ieee80211_frequency_to_channel(freq2), > > }; > > > > - if (cmd == MCU_EXT_CMD(SET_RX_PATH)) > > + if (cmd == MCU_EXT_CMD(SET_RX_PATH) || > > + dev->mt76.hw->conf.flags & IEEE80211_CONF_MONITOR) > > is this patch compliant with 802.11h DFS standard? Monitor mode would not tx packets and still follow standard. We will keep tracking this point to avoid violations. Regards, Deren > > Regards, > Lorenzo > > > req.switch_reason = CH_SWITCH_NORMAL; > > else if (phy->mt76->hw->conf.flags & IEEE80211_CONF_OFFCHANNEL) > > req.switch_reason = CH_SWITCH_SCAN_BYPASS_DPD; > > diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c > > b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c > > index 10dc4bf5adec..c56d48342aaf 100644 > > --- a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c > > +++ b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c > > @@ -2833,7 +2833,8 @@ int mt7915_mcu_set_chan_info(struct > > mt7915_phy *phy, int cmd) > > } > > #endif > > > > - if (cmd == MCU_EXT_CMD(SET_RX_PATH)) > > + if (cmd == MCU_EXT_CMD(SET_RX_PATH) || > > + dev->mt76.hw->conf.flags & IEEE80211_CONF_MONITOR) > > req.switch_reason = CH_SWITCH_NORMAL; > > else if (phy->mt76->hw->conf.flags & IEEE80211_CONF_OFFCHANNEL) > > req.switch_reason = CH_SWITCH_SCAN_BYPASS_DPD; > > diff --git a/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c > > b/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c > > index 5ef8b24f0ab3..da2be050ed7c 100644 > > --- a/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c > > +++ b/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c > > @@ -863,7 +863,8 @@ int mt7921_mcu_set_chan_info(struct mt7921_phy > > *phy, int cmd) > > else > > req.channel_band = chandef->chan->band; > > > > - if (cmd == MCU_EXT_CMD(SET_RX_PATH)) > > + if (cmd == MCU_EXT_CMD(SET_RX_PATH) || > > + dev->mt76.hw->conf.flags & IEEE80211_CONF_MONITOR) > > req.switch_reason = CH_SWITCH_NORMAL; > > else if (dev->mt76.hw->conf.flags & IEEE80211_CONF_OFFCHANNEL) > > req.switch_reason = CH_SWITCH_SCAN_BYPASS_DPD; > > -- > > 2.18.0 > >
