This patch is to add vendor command support to configure per
peer CFR parameters.
An example of usage:
iw dev wlanx vendor send 0x1374 0xad cfr-en <val> bw <bw> method <method>
periodicity <period> addr <mac_addr>
0x1374: vendor id
0xad: : vendor subcmd id
val: 0 to disable CFR capture
1 to enable CFR capture
bw: CFR capture bandwidth(use the values in enum nl80211_chan_width)
1 - 20MHZ
2 - 40MHZ
3 - 80MHZ
method: Method used by hardware to collect the CFR dump
0 - from the ACKs of QOS NULL packets
1 - from the ACKs of QOS NULL packets with phase
2 - from the ACK of probe response packet
periodicity: Periodicity in ms at which CFR dump need to be collect
0 - single shot capture
non zero - for Periodic captures
mac_addr: mac address of the peer for which CFR capture is requested.
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@xxxxxxxxxxx>
---
include/uapi/linux/nl80211-vnd-qca.h | 104 +++++++++++++++++++++++++++++++++++
1 file changed, 104 insertions(+)
create mode 100644 include/uapi/linux/nl80211-vnd-qca.h
diff --git a/include/uapi/linux/nl80211-vnd-qca.h b/include/uapi/linux/nl80211-vnd-qca.h
new file mode 100644
index 0000000..3c1158d
--- /dev/null
+++ b/include/uapi/linux/nl80211-vnd-qca.h
@@ -0,0 +1,104 @@
+/* SPDX-License-Identifier: ISC */
+/*
+ * Qualcomm Atheros OUI and vendor specific assignments
+ * Copyright (c) 2014-2017, Qualcomm Atheros, Inc.
+ * Copyright (c) 2018-2020, The Linux Foundation
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights
+ */
+
+#ifndef _UAPI_NL80211_VND_QCA_H
+#define _UAPI_NL80211_VND_QCA_H
+
+
+/* Vendor id to be used in vendor specific command and events to user space
+ * NOTE: The authoritative place for definition of QCA_NL80211_VENDOR_ID,
+ * vendor subcmd definitions prefixed with QCA_NL80211_VENDOR_SUBCMD, and
+ * qca_wlan_vendor_attr is open source file src/common/qca-vendor.h in
+ * git://w1.fi/srv/git/hostap.git; the values here are just a copy of that
+ */
+#define OUI_QCA 0x001374
+
+/**
+ * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers
+ * @QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG: This command is used to
+ * configure parameters per peer to capture Channel Frequency Response
+ * (CFR) and enable Periodic CFR capture. The attributes for this command
+ * are defined in enum qca_wlan_vendor_peer_cfr_capture_attr. This command
+ * can also be used to send CFR data from the driver to userspace when
+ * netlink events are used to send CFR data.
+ *
+ */
+enum qca_nl80211_vendor_subcmds {
+ QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG = 173,
+};
+
+/**
+ * enum qca_wlan_vendor_cfr_method - QCA vendor CFR methods used by
+ * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD as part of vendor
+ * command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG.
+ * @QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL: CFR method using QoS Null frame
+ * @QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE: CFR method using QoS Null frame
+ * with phase
+ * @QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE: CFR method using Probe Response frame
+ */
+enum qca_wlan_vendor_cfr_method {
+ QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL = 0,
+ QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE = 1,
+ QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE = 2,
+};
+
+/**
+ * enum qca_wlan_vendor_peer_cfr_capture_attr - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG to configure peer
+ * Channel Frequency Response capture parameters and enable periodic CFR
+ * capture.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR: Optional (6-byte MAC address)
+ * MAC address of peer. This is for CFR version 1 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE: Required (flag)
+ * Enable peer CFR capture. This attribute is mandatory to enable peer CFR
+ * capture. If this attribute is not present, peer CFR capture is disabled.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH: Optional (u8)
+ * BW of measurement, attribute uses the values in enum nl80211_chan_width
+ * Supported values: 20, 40, 80, 80+80, 160.
+ * Note that all targets may not support all bandwidths.
+ * This attribute is mandatory for version 1 if attribute
+ * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY: Optional (u32)
+ * Periodicity of CFR measurement in milliseconds.
+ * Periodicity should be a multiple of Base timer.
+ * Current Base timer value supported is 10 milliseconds (default).
+ * 0 for one shot capture.
+ * This attribute is mandatory for version 1 if attribute
+ * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD: Optional (u8)
+ * Method used to capture Channel Frequency Response.
+ * Attribute uses the values defined in enum qca_wlan_vendor_cfr_method.
+ * This attribute is mandatory for version 1 if attribute
+ * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE: Optional (flag)
+ * Enable periodic CFR capture.
+ * This attribute is mandatory for version 1 to enable Periodic CFR capture.
+ * If this attribute is not present, periodic CFR capture is disabled.
+ */
+enum qca_wlan_vendor_peer_cfr_capture_attr {
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR = 1,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE = 2,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH = 3,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY = 4,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD = 5,
+ QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE = 6,
+
+ /* Keep last */
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_MAX =
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST - 1,
+};
+
+#endif /* QCA_VENDOR_H */
--
2.7.4
