On 10/02/22 21:55, Marek Vasut wrote: > > On 2/10/22 17:19, Ajay.Kathat@xxxxxxxxxxxxx wrote: > > Hi, > >> On 10/02/22 14:10, Christoph Niedermaier wrote: >>> From: Ajay.Kathat@xxxxxxxxxxxxx [mailto:Ajay.Kathat@xxxxxxxxxxxxx] >>> Sent: Wednesday, February 9, 2022 3:37 PM >>>> On 08/02/22 21:56, Christoph Niedermaier wrote: >>>>> Hello, >>>>> >>>>> I tested the wireless chip wilc1000 with the 5.16.5 Kernel and the >>>>> firmware v15.4.1 >>>>> (https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/atmel/wilc1000_wifi_firmware-1.bin) >>>>> >>>>> on an i.MX6 QUAD with iperf3: >>>>> >>>>> # iperf3 -c IP_ADDR -P 16 -t 0 >>>>> >>>>> After a while the test gets stuck and I got the following kernel >>>>> messages: >>>>> mmc0: Timeout waiting for hardware interrupt. >>>>> mmc0: sdhci: ============ SDHCI REGISTER DUMP =========== >>>>> mmc0: sdhci: Sys addr: 0x138f0200 | Version: 0x00000002 >>>>> mmc0: sdhci: Blk size: 0x00000158 | Blk cnt: 0x00000001 >>>>> mmc0: sdhci: Argument: 0x14000158 | Trn mode: 0x00000013 >>>>> mmc0: sdhci: Present: 0x01d88a0a | Host ctl: 0x00000013 >>>>> mmc0: sdhci: Power: 0x00000002 | Blk gap: 0x00000080 >>>>> mmc0: sdhci: Wake-up: 0x00000008 | Clock: 0x0000009f >>>>> mmc0: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000 >>>>> mmc0: sdhci: Int enab: 0x107f100b | Sig enab: 0x107f100b >>>>> mmc0: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000003 >>>>> mmc0: sdhci: Caps: 0x07eb0000 | Caps_1: 0x0000a000 >>>>> mmc0: sdhci: Cmd: 0x0000353a | Max curr: 0x00ffffff >>>>> mmc0: sdhci: Resp[0]: 0x00001000 | Resp[1]: 0x00000000 >>>>> mmc0: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 >>>>> mmc0: sdhci: Host ctl2: 0x00000000 >>>>> mmc0: sdhci: ADMA Err: 0x00000007 | ADMA Ptr: 0x4c041200 >>>>> mmc0: sdhci-esdhc-imx: ========= ESDHC IMX DEBUG STATUS DUMP >>>>> ========= >>>>> mmc0: sdhci-esdhc-imx: cmd debug status: 0x2100 >>>>> mmc0: sdhci-esdhc-imx: data debug status: 0x2200 >>>>> mmc0: sdhci-esdhc-imx: trans debug status: 0x2300 >>>>> mmc0: sdhci-esdhc-imx: dma debug status: 0x2402 >>>>> mmc0: sdhci-esdhc-imx: adma debug status: 0x25b4 >>>>> mmc0: sdhci-esdhc-imx: fifo debug status: 0x2610 >>>>> mmc0: sdhci-esdhc-imx: async fifo debug status: 0x2751 >>>>> mmc0: sdhci: ============================================ >>>>> wilc1000_sdio mmc0:0001:1: wilc_sdio_cmd53..failed, err(-110) >>>>> wilc1000_sdio mmc0:0001:1: Failed cmd53 [0], bytes read... >>>>> >>>>> I tried to reduce the clock speed to 20MHz in the devicetree with >>>>> max-frequency = <20000000>; >>>>> but the problem then also occurs. >>>>> >>>>> Is this a possible bug? >>>>> >>>>> >>> Hi Ajay, >>> Thanks for the answer. >>> >>>> The bus error seems to be specific to the host during the SDIO >>>> transfer. >>>> How long does it take to reproduce it? Does the issue also happen >>>> without "-P 16" iPerf3 option? >>> It takes about 10s (something a bit longer) till I got this kernel >>> error >>> messages and it doesn't matter if I use it with "-P 16" or without. >> >> >> I did not observe the issue with my setup(SAMA5D4 XPLAINED + WILC1000 >> SDIO) when tested iPerf for a longer duration(~1000sec). I suspect the >> issue could be related to the SDHCI host controller. >> Try to debug the host controller side for the possible cause of timeout. > > It seems the timeout happens because the card fails to respond to SDIO > command 53, right ? > Yes, the timeout could be for any reason like either the CMD53 has not reached to chip or response not received correctly at host end. > Is there some error logging/tracing functionality in the WILC1000 > firmware which can provide further information why the card did not > respond ? WILC1000 SD module has UART serial debug port for firmware logs but I don't think it would be useful here because it needs to be debug/probe at SDIO bus level. > Could it be the card suffered some sort of FIFO overflow ? The MX6Q is a > bit more performant than the CA7 (I think?) SAMA5D4, so maybe that plays > some role ? As I understand, the issue is observed with basic iPerf testing(less throughput) so not sure if the host performance will have such an impact. IIRC few of the customers are using the same host(i.MX6) though I am not sure if it's over SPI or SDIO bus. Till now, I have not come across such limitations with the specific host. Regards, Ajay
