Ajay, On Thu, 2021-12-30 at 16:24 +0000, Ajay.Kathat@xxxxxxxxxxxxx wrote: > On 24/12/21 23:08, David Mosberger-Tang wrote: > > On Fri, 2021-12-24 at 16:20 +0000, Ajay.Kathat@xxxxxxxxxxxxx wrote: > > > On 23/12/21 22:38, David Mosberger-Tang wrote: > > > > First, on a freshly booted system and with wilc1000-spi autoloaded by > > > > the kernel, try this sequence (copy & paste the commands): > > > > > > > > /usr/sbin/wpa_supplicant -Bs -iwlan0 -c/etc/wpa_supplicant.conf > > > > sleep 10 > > > > iw dev wlan0 set power_save on > > > > > > > > The above yields a power consumption of 1.4W reliably. The "sleep 10" > > > > doesn't matter here; the behavior is the same with or without it. I > > > > tried waiting up to 120 seconds with no difference. > > > > > > I have tested by making the WILC as build-in module to insert driver > > > automatically at boot-up. I hope it should be fine. Because I have > > > already tested as loadable module earlier. > > > > > > Below are the number observed > > > ------------------------------ -------------------------- > > > - before starting wpa_supplicant : ~16.3 mA > > > - wpa_supplicant started : ~40 mA > > > - PSM on : ~6 mA > > > > > > > > > The 'sleep 10' would have no impact in my setup because I have measured > > > the current consumption for wilc1000 chip. > > > > > > I have shared the screenshot at https://postimg.cc/67S41dkb > > > > Huh, that's curious. I definitely cannot reproduce this. To match > > your setup as closely as possibly, I also built wilc1000-spi into the > > kernel, but that makes no difference (as expected). > > > > What kernel version are you on? I switched to wireless-drivers-next as > > of today (latest commit d430dffbe9dd30759f3c64b65bf85b0245c8d8ab). > > I have tested with 5.10 as well as with 5.16-rc1(commit# > fa55b7dcdc43). I don't think WILC1000 chip PS gets affected because > of a specific kernel version. > > > With this kernel, the numbers are about 100mW lower than reported > > before, but the relative behavior is the same: about 300mW higher > > power-consumption when PSM is not taking effect properly. > > > > To recap, back with wilc1000-spi being a module again, after freshly > > booting the system and issuing this commands: > > > > /usr/sbin/wpa_supplicant -Bs -iwlan0 -c/etc/wpa_supplicant.conf > > /usr/sbin/iw dev wlan0 set power_save on > > > > I see a power-consumption of about 1.25W. PSM on/off makes no > > difference in this state. Then, if I issue the commands: > > > > rmmod wilc1000-spi > > modprobe wilc1000-spi > > sleep 10 > > iw dev wlan0 set power_save on > > > > power-consumption drops to about 0.9W. > > > > Here is a screenshot that shows the annotated power-measurements: > > > > https://postimg.cc/3dbKSGht > > > > Apart from kernel version, the only things that I can think of that'd > > be different is that we don't have the ENABLE pin wired to a GPIO. > > Instead, the chip is always enabled. I doubt this would explain the > > difference (~RESET is wired to a GPIO). > > When PS mode is enabled, the host can wake-up the chip, if there is > some data to transfer. Just check, if there is any network > application trying to access WILC (send continuous data) in your > setup. That shouldn't be an issue. To confirm, in the output below, I included the ifconfig stats so you can see that there is virtually no traffic during the measurement periods. > Also, you have mentioned that removing the module(without killing > the wpa_supplicant) worked so I guess, it might be possible that the > application got interrupted when the module was removed and didn't > start when the module was inserted again. There are no applications running on the system at all. I tested the two command sequences in the exact same setup, with everything that normally runs on our system disabled. CPU utilization is basically 0%. > Try disabling CONFIG_CFG80211_DEFAULT_PS config to check if it has any impact. I already had CONFIG_CFG80211_DEFAULT_PS disabled. It makes no difference, except that with CONFIG_CFG80211_DEFAULT_PS enabled, you have to issue "power_save off" before "power_save on" to get PSM to take effect since cfg80211 thinks power-save is already enabled when it's not. To mirror your setup more closely, I installed a 1 ohm shunt resistor on the 3.3V supply to the WILC1000 so I can measure current draw of the WILC1000 alone. This is just for paranoia's sake to make sure there is nothing wonky going on outside of the WILC1000 (there is not). So the current draws mentioned below are at 3.3V and DC average measures across 1 minute. First test command sequence (power saving fails to take effect): ------------------------------------------------------------------ REBOOT SYSTEM # ifconfig wlan0 | tail -5 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) # /usr/sbin/wpa_supplicant -Bs -iwlan0 -c/etc/wpa_supplicant.conf # iw dev wlan0 set power_save on # sleep 60 # ifconfig wlan0 | tail -5 RX packets:51 errors:0 dropped:0 overruns:0 frame:0 TX packets:37 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5980 (5.8 KiB) TX bytes:5425 (5.2 KiB) ------------------------------------------------------------------ with the above command sequence, current-draw remains pretty much constant at 76mA. Second test command sequence (power saving successfully takes effect): ------------------------------------------------------------------ REBOOT SYSTEM # ifconfig wlan0 | tail -5 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) # /usr/sbin/wpa_supplicant -Bs -iwlan0 -c/etc/wpa_supplicant.conf # sleep 15 # iw dev wlan0 set power_save on # sleep 60 # ifconfig wlan0 | tail -5 RX packets:41 errors:0 dropped:0 overruns:0 frame:0 TX packets:34 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5007 (4.8 KiB) TX bytes:5436 (5.3 KiB) ------------------------------------------------------------------ with the above command sequence, current-draw fluctuates quite a bit, but averages to somewhere around 15mA. The exact amount of time needed between starting wpa_supplicant and issuing the PSM on command fluctuates a bit. Sometimes 9 seconds is enough, but oftentimes a pause of 10-15 seconds is required. A screenshot of the current draw for this command sequence is graphed here: https://postimg.cc/bZc1v0jR Oh, and just at the off-chance that the association details matters: # wpa_cli status Selected interface 'wlan0' bssid=d8:07:b6:af:4b:e4 freq=2442 ssid=MOSTANG id=0 mode=station pairwise_cipher=CCMP group_cipher=CCMP key_mgmt=WPA2-PSK wpa_state=COMPLETED p2p_device_address=f8:f0:05:62:76:48 address=f8:f0:05:62:76:48 uuid=22b21bb3-ec5a-5038-aa7f-911a2b012173 --david
