Jouni Malinen <jouni@xxxxxxxxxxxxxx> writes:
> From: Anilkumar Kolli <akolli@xxxxxxxxxxxxxx>
>
> Add a new hw_param full_monitor_mode to enable full monitor support for
> QCN9074. HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE cmd is sent to the
> firmware to enable the full monitor mode.
>
> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
>
> Signed-off-by: Anilkumar Kolli <akolli@xxxxxxxxxxxxxx>
> Signed-off-by: Jouni Malinen <jouni@xxxxxxxxxxxxxx>
> ---
> drivers/net/wireless/ath/ath11k/core.c | 4 ++
> drivers/net/wireless/ath/ath11k/dp.h | 74 +++++++++++++++++++++++++
> drivers/net/wireless/ath/ath11k/dp_tx.c | 48 ++++++++++++++++
> drivers/net/wireless/ath/ath11k/dp_tx.h | 2 +
> drivers/net/wireless/ath/ath11k/hw.h | 1 +
> 5 files changed, 129 insertions(+)
>
> diff --git a/drivers/net/wireless/ath/ath11k/core.c b/drivers/net/wireless/ath/ath11k/core.c
> index 969bf1a590d9..3179495cb3c9 100644
> --- a/drivers/net/wireless/ath/ath11k/core.c
> +++ b/drivers/net/wireless/ath/ath11k/core.c
> @@ -65,6 +65,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
> BIT(NL80211_IFTYPE_AP) |
> BIT(NL80211_IFTYPE_MESH_POINT),
> .supports_monitor = true,
> + .full_monitor_mode = false,
> .supports_shadow_regs = false,
> .idle_ps = false,
> .cold_boot_calib = true,
> @@ -106,6 +107,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
> BIT(NL80211_IFTYPE_AP) |
> BIT(NL80211_IFTYPE_MESH_POINT),
> .supports_monitor = true,
> + .full_monitor_mode = false,
> .supports_shadow_regs = false,
> .idle_ps = false,
> .cold_boot_calib = true,
> @@ -146,6 +148,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
> .interface_modes = BIT(NL80211_IFTYPE_STATION) |
> BIT(NL80211_IFTYPE_AP),
> .supports_monitor = false,
> + .full_monitor_mode = false,
> .supports_shadow_regs = true,
> .idle_ps = true,
> .cold_boot_calib = false,
> @@ -184,6 +187,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
> BIT(NL80211_IFTYPE_AP) |
> BIT(NL80211_IFTYPE_MESH_POINT),
> .supports_monitor = true,
> + .full_monitor_mode = true,
> .supports_shadow_regs = false,
> .idle_ps = false,
> .cold_boot_calib = false,
wcn6855 was not updated, I added that.
> --- a/drivers/net/wireless/ath/ath11k/dp_tx.c
> +++ b/drivers/net/wireless/ath/ath11k/dp_tx.c
> @@ -1034,6 +1034,15 @@ int ath11k_dp_tx_htt_monitor_mode_ring_config(struct ath11k *ar, bool reset)
> struct htt_rx_ring_tlv_filter tlv_filter = {0};
> int ret = 0, ring_id = 0, i;
>
> + if (ab->hw_params.full_monitor_mode) {
> + ret = ath11k_dp_tx_htt_rx_full_mon_setup(ab,
> + dp->mac_id, !reset);
> + if (ret < 0) {
> + ath11k_err(ab, "failed to setup full monitor %d\n", ret);
I changed this to:
if (ret) {
ath11k_warn(ab, "failed to setup full monitor: %d\n", ret);
return ret;
}
--
https://patchwork.kernel.org/project/linux-wireless/list/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
