On 2021-09-23 16:59, Manivannan Sadhasivam wrote:
On Thu, Sep 23, 2021 at 04:34:43PM +0800, Carl Huang wrote:
On 2021-09-17 01:19, Manivannan Sadhasivam wrote:
> On Thu, Sep 16, 2021 at 07:42:02PM +0300, Kalle Valo wrote:
> > Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx> writes:
> >
> > > On Thu, Sep 16, 2021 at 01:18:22PM +0200, Loic Poulain wrote:
> > >> Le jeu. 16 sept. 2021 à 13:12, Manivannan Sadhasivam <
> > >> manivannan.sadhasivam@xxxxxxxxxx> a écrit :
> > >>
> > >
> > > [...]
> > >
> > >> > If things seems to work fine without that patch, then it implies that
> > >> > setting M0
> > >> > state works during resume. I think we should just revert that patch.
> > >> >
> > >> > Loic, did that patch fix any issue for you or it was a cosmetic fix only?
> > >>
> > >>
> > >> It fixes sdx modem resuming issue, without that we don’t know modem needs
> > >> to be reinitialized.
> > >>
> > >
> > > Okay. Then in that case, the recovery mechanism has to be added to the ath11k
> > > MHI controller.
> >
> > What does that mean in practise, do you have any pointers or
> > examples? I
> > have no clue what you are proposing :)
> >
>
> Take a look at the mhi_pci_recovery_work() function below:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/bus/mhi/pci_generic.c#n610
>
> You need to implement something similar that basically powers up the MHI
> endpoint (QCA6390) in case pm_resume() fails. At minimum, you need to
> call
> below functions:
>
> # Check if the device is powered on. If yes, then power it down to bring
> it back
> mhi_power_down()
> mhi_unprepare_after_power_down()
>
> # Power up the device
> mhi_prepare_for_power_up()
> mhi_sync_power_up()
>
> This implies that the WLAN device has been powered off during suspend,
> so the
> resume fails and we are bringing the device back to working state.
>
This is fine for platform which doesn't provide power supply during
suspend.
But NUC has power supply in suspend state.
If NUC retains power supply during suspend then it should work with
that commit.
During resume, the device is expected to be in M3 state and that's what
the
commit verifies.
If the device is in a different state, then most likely the device have
power
cycled.
But the tricky thing here is that upstream QCA6390 doesn't have recovery
mechanism to download
firmware again, so QCA6390 has no way to work after a power cycle.
QCA6390 on NUC works after just reverting this commit also proves NUC
has
power supply in
suspend state.
That's because we allowed the device to be in any state during resume
and if it
responds to the M0 transition it worked.
The reason is MHI-STATUS register can't be read somehow in M3 state on
NUC.
No, that's not correct.
Does the MHI spec state that MHI-STATUS register can be read in M3
state?
Yes, all the MHI registers are accessible in all states. During M3,
both MHI
host and device (if supported) will transition to D3 Cold. Then during
resume,
host will switch to D0 link state and will also notify the device to
enter D0.
For aid debugging, please see the state the device is in during
mhi_pm_resume().
You can use below diff:
diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index fb99e3727155..482d55dd209e 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -898,6 +898,9 @@ int mhi_pm_resume(struct mhi_controller *mhi_cntrl)
if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state))
return -EIO;
+ dev_info(dev, "Device state: %s\n",
+ TO_MHI_STATE_STR(mhi_get_mhi_state(mhi_cntrl)));
+
if (mhi_get_mhi_state(mhi_cntrl) != MHI_STATE_M3)
return -EINVAL;
Thanks,
Mani
