Hello rtw88 maintainers and contributors,
there is an ongoing effort where Jernej and I are working on adding
SDIO support to the rtw88 driver.
The hardware we use at the moment is RTL8822BS and RTL8822CS.
Work-in-progress code can be found in Jernej's repo (note: this may be
rebased): [0]
We are at a point where we can communicate with the SDIO card and
successfully upload the firmware to it.
Right now I have two questions about the locking in
rtw_{read,write}_rf from hci.h:
1) A spinlock is used to protect RF register access. This is
problematic for SDIO, more information below. Would you accept a patch
to convert this into a mutex? I don't have any rtw88 PCIe card for
testing any regressions there myself.
2) I would like to understand why the RF register access needs to be
protected by a lock. From what I can tell RF register access doesn't
seem to be used from IRQ handlers.
Some background on why SDIO access (for example: sdio_writeb) cannot
be done with a spinlock held:
- when using for example sdio_writeb the MMC subsystem in Linux
prepares a so-called MMC request
- this request is submitted to the MMC host controller hardware
- the host controller hardware forwards the MMC request to the card
- the card signals when it's done processing the request
- the MMC subsystem in Linux waits for the card to signal that it's
done processing the request in mmc_wait_for_req_done() -> this uses
wait_for_completion() internally, which might sleep (which is not
allowed while a spinlock is held)
I am looking forward to your advice on this rtw_{read,write}_rf locking topic.
Thank you and best regards,
Martin
[0] https://github.com/jernejsk/linux-1/commits/rtw88-sdio
[ 27.249435] BUG: scheduling while atomic: ip/2749/0x00000002
[ 27.249482] Modules linked in:
[ 27.252485] CPU: 2 PID: 2749 Comm: ip Not tainted 5.14.0-rc1+ #30
[ 27.258521] Hardware name: Shenzhen Amediatech Technology Co., Ltd X96 Air (DT)
[ 27.265767] Call trace:
[ 27.268181] dump_backtrace+0x0/0x19c
[ 27.271804] show_stack+0x1c/0x30
[ 27.275081] dump_stack_lvl+0x68/0x84
[ 27.278702] dump_stack+0x1c/0x38
[ 27.281980] __schedule_bug+0x60/0x80
[ 27.285602] __schedule+0x600/0x6c0
[ 27.289052] schedule+0x74/0x110
[ 27.292243] schedule_timeout+0xc0/0xf0
[ 27.296039] wait_for_completion+0x80/0x120
[ 27.300178] mmc_wait_for_req_done+0x6c/0xa0
[ 27.304404] mmc_wait_for_req+0xb4/0x104
[ 27.308286] mmc_io_rw_extended+0x1cc/0x2c0
[ 27.312426] sdio_io_rw_ext_helper+0x194/0x240
[ 27.316824] sdio_memcpy_toio+0x28/0x34
[ 27.320619] rtw_sdio_write_block+0x88/0xf0
[ 27.324760] rtw_sdio_write+0x138/0x18c
[ 27.328555] rtw_sdio_write32+0x3c/0x90
[ 27.332349] rtw_phy_write_rf_reg_sipi+0x98/0xf4
[ 27.336921] rtw_phy_write_rf_reg_mix+0x18/0x40
[ 27.341406] rtw_phy_cfg_rf+0x74/0xd0
[ 27.345028] rtw_parse_tbl_phy_cond+0x130/0x180
[ 27.349513] rtw_phy_load_tables+0x178/0x1a0
[ 27.353739] rtw8822c_phy_set_param+0x114/0xe40
[ 27.358224] rtw_core_start+0xb0/0x240
[ 27.361934] rtw_ops_start+0x30/0x50
[ 27.365469] drv_start+0x38/0x60
[ 27.368661] ieee80211_do_open+0x188/0x7d0
[ 27.372714] ieee80211_open+0x64/0xb0
[ 27.376337] __dev_open+0x10c/0x1c0
[ 27.379787] __dev_change_flags+0x194/0x210
[ 27.383927] dev_change_flags+0x28/0x6c
[ 27.387723] do_setlink+0x204/0xd14
[ 27.391173] __rtnl_newlink+0x484/0x830
[ 27.394967] rtnl_newlink+0x50/0x80
[ 27.398418] rtnetlink_rcv_msg+0x120/0x334
[ 27.402472] netlink_rcv_skb+0x5c/0x130
[ 27.406267] rtnetlink_rcv+0x1c/0x2c
[ 27.409803] netlink_unicast+0x2bc/0x310
[ 27.413683] netlink_sendmsg+0x1a8/0x3d0
[ 27.417565] ____sys_sendmsg+0x250/0x294
[ 27.421447] ___sys_sendmsg+0x7c/0xc0
[ 27.425068] __sys_sendmsg+0x68/0xc4
[ 27.428605] __arm64_sys_sendmsg+0x28/0x3c
[ 27.432659] invoke_syscall+0x48/0x114
[ 27.436367] el0_svc_common+0xc4/0xdc
[ 27.439991] do_el0_svc+0x2c/0x94
[ 27.443267] el0_svc+0x2c/0x54
[ 27.446286] el0t_64_sync_handler+0xa8/0x12c
[ 27.450513] el0t_64_sync+0x198/0x19c
