Found by latest checkpatch.
Signed-off-by: Kalle Valo <kvalo@xxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/ath10k/core.c | 2 +-
drivers/net/wireless/ath/ath10k/debug.c | 2 +-
drivers/net/wireless/ath/ath10k/mac.c | 2 +-
drivers/net/wireless/ath/ath10k/rx_desc.h | 2 +-
drivers/net/wireless/ath/ath10k/sdio.c | 2 +-
drivers/net/wireless/ath/ath10k/wmi.h | 4 ++--
6 files changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index d73ad60b571c..419b06b974c5 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -2636,7 +2636,7 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode,
if (status)
goto err;
- /* Some of of qca988x solutions are having global reset issue
+ /* Some of qca988x solutions are having global reset issue
* during target initialization. Bypassing PLL setting before
* downloading firmware and letting the SoC run on REF_CLK is
* fixing the problem. Corresponding firmware change is also
diff --git a/drivers/net/wireless/ath/ath10k/debug.c b/drivers/net/wireless/ath/ath10k/debug.c
index e8250a665433..b72cd81fdc79 100644
--- a/drivers/net/wireless/ath/ath10k/debug.c
+++ b/drivers/net/wireless/ath/ath10k/debug.c
@@ -1764,7 +1764,7 @@ static ssize_t ath10k_write_simulate_radar(struct file *file,
struct ath10k *ar = file->private_data;
struct ath10k_vif *arvif;
- /* Just check for for the first vif alone, as all the vifs will be
+ /* Just check for the first vif alone, as all the vifs will be
* sharing the same channel and if the channel is disabled, all the
* vifs will share the same 'is_started' state.
*/
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 2e3eb5bbe49c..c857cf46832d 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -5457,7 +5457,7 @@ static int ath10k_add_interface(struct ieee80211_hw *hw,
/* Some firmware revisions don't wait for beacon tx completion before
* sending another SWBA event. This could lead to hardware using old
* (freed) beacon data in some cases, e.g. tx credit starvation
- * combined with missed TBTT. This is very very rare.
+ * combined with missed TBTT. This is very rare.
*
* On non-IOMMU-enabled hosts this could be a possible security issue
* because hw could beacon some random data on the air. On
diff --git a/drivers/net/wireless/ath/ath10k/rx_desc.h b/drivers/net/wireless/ath/ath10k/rx_desc.h
index dec1582005b9..f2b6bf8f0d60 100644
--- a/drivers/net/wireless/ath/ath10k/rx_desc.h
+++ b/drivers/net/wireless/ath/ath10k/rx_desc.h
@@ -68,7 +68,7 @@ struct rx_attention {
* first_msdu is set.
*
* peer_idx_invalid
- * Indicates no matching entries within the the max search
+ * Indicates no matching entries within the max search
* count. Only set when first_msdu is set.
*
* peer_idx_timeout
diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c
index 81ddaafb6721..59043ec44ca3 100644
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -1248,7 +1248,7 @@ static int ath10k_sdio_bmi_exchange_msg(struct ath10k *ar,
* Wait for first 4 bytes to be in FIFO
* If CONSERVATIVE_BMI_READ is enabled, also wait for
* a BMI command credit, which indicates that the ENTIRE
- * response is available in the the FIFO
+ * response is available in the FIFO
*
* CASE 3: length > 128
* Wait for the first 4 bytes to be in FIFO
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index 4898e19b0af6..11300b1320a9 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -3832,7 +3832,7 @@ enum wmi_pdev_param {
WMI_PDEV_PARAM_BEACON_TX_MODE,
/*
* Resource manager off chan mode .
- * 0: turn off off chan mode. 1: turn on offchan mode
+ * 0: turn off offchan mode. 1: turn on offchan mode
*/
WMI_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
/*
@@ -3936,7 +3936,7 @@ enum wmi_10x_pdev_param {
WMI_10X_PDEV_PARAM_BEACON_TX_MODE,
/*
* Resource manager off chan mode .
- * 0: turn off off chan mode. 1: turn on offchan mode
+ * 0: turn off offchan mode. 1: turn on offchan mode
*/
WMI_10X_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
/*
--
2.7.4
