Am 20.05.2020 um 12:40 schrieb Vincent Wiemann:
Hi Sebastian,
I don't know why it was dropped, but I can say that the LED control code was kind of
annoying me. Even when the LED was turned of, it "flickered" when it was set disabled.
Unfortunately I didn't have time to look into it, yet.
the led code will just be used if you set a trigger. otherwise it doesnt
touch the gpios.
the code itself was written to make use of the led's builtin to several
routers. if you dont set a led trigger, nothing will happen
Best,
Vincent
On 20.05.20 09:39, Sebastian Gottschall wrote:
this code is not in use in its original form for ipq4019.
i have seen that his patch is also dropped from ath.git but is still in use by openwrt.
could somone clarify the state here and why it was dropped?
the original patch i wrote does exclude the soc chipsets, but the patch was later reorganized and some part have been rewritten
so i'm not sure if it covers the scenario mentioned here, which i did take care of
Sebastian
Am 26.02.2019 um 10:16 schrieb Sven Eckelmann:
On Friday, 6 April 2018 17:17:55 CET Kalle Valo wrote:
From: Sebastian Gottschall <s.gottschall@xxxxxxxxxxxxxxx>
Adds LED and GPIO Control support for 988x, 9887, 9888, 99x0, 9984 based
chipsets with on chipset connected led's using WMI Firmware API. The LED
device will get available named as "ath10k-phyX" at sysfs and can be controlled
with various triggers. adds also debugfs interface for gpio control.
Signed-off-by: Sebastian Gottschall <s.gottschall@xxxxxxxxxx>
Reviewed-by: Steve deRosier <derosier@xxxxxxxxxxxxxx>
[kvalo: major reorg and cleanup]
Signed-off-by: Kalle Valo <kvalo@xxxxxxxxxxxxxx>
This patch was imported to OpenWrt in commit 61d57a2f88b9 ("mac80211: ath10k
add leds support") and broke the 11s support for IPQ4019 and QCA4019 (5GHz)
firmware versions 10.4-3.5.3-00053, 10.4-3.5.3-00057, 10.4-3.6-00140:
[ 221.620803] ath10k_pci 0000:01:00.0: wmi command 36967 timeout, restarting hardware
[ 221.744056] ieee80211 phy0: Hardware restart was requested
[ 225.130829] ath10k_pci 0000:01:00.0: failed to receive control response completion, polling..
[ 226.170824] ath10k_pci 0000:01:00.0: Service connect timeout
[ 226.170871] ath10k_pci 0000:01:00.0: failed to connect htt (-110)
[ 226.252248] ath10k_pci 0000:01:00.0: Could not init core: -110
This was tested on an A62 with following wireless config:
config wifi-device 'radio0'
option type 'mac80211'
option channel '36'
option hwmode '11a'
option path 'soc/40000000.pci/pci0000:00/0000:00:00.0/0000:01:00.0'
option htmode 'VHT80'
option disabled '0'
option country US
config wifi-device 'radio1'
option type 'mac80211'
option channel '11'
option hwmode '11g'
option path 'platform/soc/a000000.wifi'
option htmode 'HT20'
option disabled '0'
option country US
config wifi-device 'radio2'
option type 'mac80211'
option channel '149'
option hwmode '11a'
option path 'platform/soc/a800000.wifi'
option htmode 'VHT80'
option disabled '0'
option country US
config wifi-iface 'mesh0'
option device 'radio0'
option ifname 'mesh0'
option network 'nwi_mesh0'
option mode 'mesh'
option mesh_id 'TestMesh'
option mesh_fwding '1'
option encryption 'none'
config wifi-iface 'mesh1'
option device 'radio1'
option ifname 'mesh1'
option network 'nwi_mesh1'
option mode 'mesh'
option mesh_id 'TestMesh'
option encryption 'none'
config wifi-iface 'mesh2'
option device 'radio2'
option ifname 'mesh2'
option network 'nwi_mesh2'
option mode 'mesh'
option mesh_id 'TestMesh'
option mesh_fwding '1'
option encryption 'none
Kind regards,
Sven
_______________________________________________
openwrt-devel mailing list
openwrt-devel@xxxxxxxxxxxxxxxxx
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
