From: Erik Stromdahl <erik.stromdahl@xxxxxxxxx> Add hardware parameters for QCA9377 sdio devices, it's now properly supported. Signed-off-by: Erik Stromdahl <erik.stromdahl@xxxxxxxxx> Signed-off-by: Kalle Valo <kvalo@xxxxxxxxxxxxxx> --- I don't have any working QCA9377 SDIO hardware so I would appreciate any test reports. This should apply cleanly to ath.git master branch (at least to tag ath-201909230832): https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git/log/?h=master drivers/net/wireless/ath/ath10k/core.c | 27 +++++++++++++++++++++++++++ drivers/net/wireless/ath/ath10k/hw.h | 3 +++ 2 files changed, 30 insertions(+) diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c index 36c62d66c19e..e5572d4b6ae9 100644 --- a/drivers/net/wireless/ath/ath10k/core.c +++ b/drivers/net/wireless/ath/ath10k/core.c @@ -539,6 +539,33 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = { .tx_stats_over_pktlog = false, }, { + .id = QCA9377_HW_1_1_DEV_VERSION, + .dev_id = QCA9377_1_0_DEVICE_ID, + .bus = ATH10K_BUS_SDIO, + .name = "qca9377 hw1.1 sdio", + .patch_load_addr = QCA9377_HW_1_0_PATCH_LOAD_ADDR, + .uart_pin = 19, + .otp_exe_param = 0, + .channel_counters_freq_hz = 88000, + .max_probe_resp_desc_thres = 0, + .cal_data_len = 8124, + .fw = { + .dir = QCA9377_HW_1_0_FW_DIR, + .board = QCA9377_HW_1_0_BOARD_DATA_FILE, + .board_size = QCA9377_BOARD_DATA_SZ, + .board_ext_size = QCA9377_BOARD_EXT_DATA_SZ, + }, + .hw_ops = &qca6174_ops, + .hw_clk = qca6174_clk, + .target_cpu_freq = 176000000, + .decap_align_bytes = 4, + .n_cipher_suites = 8, + .num_peers = TARGET_QCA9377_HL_NUM_PEERS, + .ast_skid_limit = 0x10, + .num_wds_entries = 0x20, + .uart_pin_workaround = true, + }, + { .id = QCA4019_HW_1_0_DEV_VERSION, .dev_id = 0, .bus = ATH10K_BUS_AHB, diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h index 2ae57c1de7b5..ddb1d23ec6de 100644 --- a/drivers/net/wireless/ath/ath10k/hw.h +++ b/drivers/net/wireless/ath/ath10k/hw.h @@ -768,6 +768,9 @@ ath10k_is_rssi_enable(struct ath10k_hw_params *hw, #define TARGET_HL_TLV_AST_SKID_LIMIT 16 #define TARGET_HL_TLV_NUM_WDS_ENTRIES 2 +/* Target specific defines for QCA9377 high latency firmware */ +#define TARGET_QCA9377_HL_NUM_PEERS 15 + /* Diagnostic Window */ #define CE_DIAG_PIPE 7 -- 2.7.4
