Hi, I met failure to resume from suspend to RAM with v5.1.19 and TP-Link Archer T2UH connected to my PC (Asus P8H77-V). I tried about a dozen times while trying to figure out the reason, the issue happened every time. Eventually I connected a serial console and captured this: [ 87.803576][ T4640] mt76x0u 2-1.6:1.0: vendor request req:06 off:ac80 failed:-110 [ 91.030328][ T4640] mt76x0u 2-1.6:1.0: vendor request req:07 off:b000 failed:-110 [ 94.256950][ T4640] mt76x0u 2-1.6:1.0: vendor request req:06 off:b000 failed:-110 [ 97.483579][ T4640] mt76x0u 2-1.6:1.0: vendor request req:06 off:aca0 failed:-110 (repeats) [ 100.211748][ C0] sysrq: Show Blocked State [ 107.479820][ C0] kworker/u8:51 D 0 4640 2 0x80000000 [ 107.486060][ C0] Workqueue: events_unbound async_run_entry_fn [ 107.492106][ C0] Call Trace: [ 107.495293][ C0] ? __schedule+0x381/0xa30 [ 107.499706][ C0] schedule+0x36/0x90 [ 107.503575][ C0] schedule_timeout+0x1e8/0x4c0 [ 107.508310][ C0] ? collect_expired_timers+0xb0/0xb0 [ 107.513593][ C0] wait_for_common+0x15f/0x190 [ 107.518249][ C0] ? wake_up_q+0x80/0x80 [ 107.522412][ C0] usb_start_wait_urb+0x82/0x160 [ 107.527222][ C0] ? wait_for_common+0x38/0x190 [ 107.531961][ C0] usb_control_msg+0xdc/0x140 [ 107.536542][ C0] __mt76u_vendor_request+0xc4/0x100 [mt76_usb] [ 107.542687][ C0] mt76u_copy+0x8b/0xb0 [mt76_usb] [ 107.547721][ C0] mt76x02_mac_shared_key_setup+0xdf/0x130 [mt76x02_lib] [ 107.554653][ C0] mt76x0_init_hardware+0x2b5/0x3a0 [mt76x0_common] [ 107.561141][ C0] ? usb_dev_thaw+0x10/0x10 [ 107.565533][ C0] mt76x0u_init_hardware+0x134/0x1b0 [mt76x0u] [ 107.571609][ C0] mt76x0_resume+0x33/0x60 [mt76x0u] [ 107.576791][ C0] usb_resume_interface.isra.1+0x81/0xd0 [ 107.582310][ C0] usb_resume_both+0xe8/0x130 [ 107.586888][ C0] usb_resume+0x16/0x60 [ 107.590936][ C0] dpm_run_callback+0x6e/0x190 [ 107.595599][ C0] device_resume+0x99/0x190 [ 107.599982][ C0] async_resume+0x19/0x30 [ 107.604204][ C0] async_run_entry_fn+0x37/0x140 Any ideas about it? FWIW, I've used a TL-WN722N so far without problems, just switched to the T2UH today. The whole machine is hanging at this point. without serial console my only choice was to press the reset button. At least mt76x0u should bail out with an error and not block the resume completely. Unplugging the hardware also didn't cause it to bail. Thanks, Johannes
