Search Linux Wireless

[PATCH 3/3] brcmfmac: sdio: Disable auto-tuning around commands expected to fail

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus.  This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times.  The comment in the code reinforces this by saying
"just one write attempt may fail"

Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.

Let's disable retuning around the commands we expect might fail.

Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
---

 drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
index 3fd2d58a3c88..c09bb8965487 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c
@@ -27,6 +27,7 @@
 #include <linux/mmc/sdio_ids.h>
 #include <linux/mmc/sdio_func.h>
 #include <linux/mmc/card.h>
+#include <linux/mmc/core.h>
 #include <linux/semaphore.h>
 #include <linux/firmware.h>
 #include <linux/module.h>
@@ -708,6 +709,7 @@ brcmf_sdio_kso_control(struct brcmf_sdio *bus, bool on)
 		bmask = SBSDIO_FUNC1_SLEEPCSR_KSO_MASK;
 	}
 
+	mmc_expect_errors_begin(bus->sdiodev->func1->card->host);
 	do {
 		/* reliable KSO bit set/clr:
 		 * the sdiod sleep write access is synced to PMU 32khz clk
@@ -730,6 +732,7 @@ brcmf_sdio_kso_control(struct brcmf_sdio *bus, bool on)
 				   &err);
 
 	} while (try_cnt++ < MAX_KSO_ATTEMPTS);
+	mmc_expect_errors_end(bus->sdiodev->func1->card->host);
 
 	if (try_cnt > 2)
 		brcmf_dbg(SDIO, "try_cnt=%d rd_val=0x%x err=%d\n", try_cnt,
-- 
2.21.0.1020.gf2820cf01a-goog




[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Wireless Regulations]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux