> Is this known bug? I can see my wireless network using wlist
> wlan0 scan.
This card (which seems to be a 4306 rev 3 like yours), works for me:
03:00.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03)
Subsystem: Melco Inc Unknown device [1154:0324]
Flags: bus master, fast devsel, latency 64, IRQ 11
Memory at 5c000000 (32-bit, non-prefetchable) [size=8K]
I'm currently associated via WPA2 to an AP.
Inserting the card:
pccard: CardBus card inserted into slot 0
b43-pci-bridge 0000:03:00.0: enabling device (0000 -> 0002)
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:03:00.0 to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:03:00.0
b43-phy0: Broadcom 4306 WLAN found
phy0: Selected rate control algorithm 'pid'
Broadcom 43xx driver loaded [ Features: PML, Firmware-ID: FW13 ]
Associating:
firmware: requesting b43/ucode5.fw
firmware: requesting b43/pcm5.fw
firmware: requesting b43/b0g0initvals5.fw
firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
phy0: HW CONFIG: freq=2412
phy0: HW CONFIG: freq=2412
phy0: HW CONFIG: freq=2417
phy0: HW CONFIG: freq=2422
phy0: HW CONFIG: freq=2427
phy0: HW CONFIG: freq=2432
phy0: HW CONFIG: freq=2437
phy0: HW CONFIG: freq=2442
phy0: HW CONFIG: freq=2447
phy0: HW CONFIG: freq=2452
phy0: HW CONFIG: freq=2457
phy0: HW CONFIG: freq=2462
phy0: HW CONFIG: freq=2412
phy0: HW CONFIG: freq=2437
phy0: HW CONFIG: freq=2437
eth1: authenticate with AP 00:13:19:80:da:30
eth1: authenticated
eth1: associate with AP 00:13:19:80:da:30
eth1: RX AssocResp from 00:13:19:80:da:30 (capab=0x11 status=0 aid=2)
eth1: associated
phy0: Allocated STA 00:13:19:80:da:30
phy0: Inserted STA 00:13:19:80:da:30
eth1: switched to short barker preamble (BSSID=00:13:19:80:da:30)
eth1: switched to long barker preamble (BSSID=00:13:19:80:da:30)
> How do I make it use the b43legacy
This is for a different card / firmware. Please refer to
http://wireless.kernel.org/en/users/Drivers/b43 for more
information. There's a section there "bcm43xx, b43legacy, b43,
softmac,... the full story". b43legacy won't solve your problem.
> I'm using opensuse 11 and have compiled the latest code and it
> is still not working. This worked BTW, in 10.2 and 10.3 with no
> problems and the card is currently working in vista (ugh).
Then it's a SuSE-Problem and you should ask your vendor.
However, you wrote "I compiled latest code" without specifing
what "latest" is. I'm using almost-latest-code (tm), e.g. I used
for my test wireless-testing, git describe
"v2.6.26-rc9-14207-ga520bdb".
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
