From: Ondrej Jirman <megous@xxxxxxxxxx>
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c1352 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@xxxxxxxxxx>
---
drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c | 1 +
drivers/pinctrl/sunxi/pinctrl-sunxi.c | 10 ++++++++++
drivers/pinctrl/sunxi/pinctrl-sunxi.h | 4 ++++
3 files changed, 15 insertions(+)
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c
index ef4268cc6227..30b1befa8ed8 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c
@@ -591,6 +591,7 @@ static const struct sunxi_pinctrl_desc h6_pinctrl_data = {
.irq_banks = 4,
.irq_bank_map = h6_irq_bank_map,
.irq_read_needs_mux = true,
+ .io_bias_cfg_variant = IO_BIAS_CFG_V2,
};
static int h6_pinctrl_probe(struct platform_device *pdev)
diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.c b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
index b8dd58ef33b7..0ab50a15a716 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sunxi.c
+++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
@@ -607,6 +607,8 @@ static int sunxi_pinctrl_set_io_bias_cfg(struct sunxi_pinctrl *pctl,
unsigned pin,
struct regulator *supply)
{
+ unsigned short bank = pin / PINS_PER_BANK;
+ unsigned long flags;
u32 val, reg;
int uV;
@@ -642,6 +644,14 @@ static int sunxi_pinctrl_set_io_bias_cfg(struct sunxi_pinctrl *pctl,
reg = readl(pctl->membase + sunxi_grp_config_reg(pin));
reg &= ~IO_BIAS_MASK;
writel(reg | val, pctl->membase + sunxi_grp_config_reg(pin));
+ } else if (pctl->desc->io_bias_cfg_variant == IO_BIAS_CFG_V2) {
+ val = uV <= 1800000 ? 1 : 0;
+
+ raw_spin_lock_irqsave(&pctl->lock, flags);
+ reg = readl(pctl->membase + PIO_POW_MOD_SEL_REG);
+ reg &= ~(1 << bank);
+ writel(reg | val << bank, pctl->membase + PIO_POW_MOD_SEL_REG);
+ raw_spin_unlock_irqrestore(&pctl->lock, flags);
}
return 0;
diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.h b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
index 642f667e99d2..4044a3cb1819 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sunxi.h
+++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
@@ -95,8 +95,12 @@
#define PINCTRL_SUN7I_A20 BIT(7)
#define PINCTRL_SUN8I_R40 BIT(8)
+#define PIO_POW_MOD_SEL_REG 0x340
+
/* Bias voltage configuration done via Pn_GRP_CONFIG registers. */
#define IO_BIAS_CFG_V1 1
+/* Bias voltage set in the PIO_POW_MOD_SEL_REG register. */
+#define IO_BIAS_CFG_V2 2
struct sunxi_desc_function {
unsigned long variant;
--
2.21.0
