On Sun, Apr 07, 2019 at 05:31:52PM +0200, Clément Péron wrote: > Hi, > > On Sat, 6 Apr 2019 at 01:45, megous via linux-sunxi > <linux-sunxi@xxxxxxxxxxxxxxxx> wrote: > > > > From: Ondrej Jirman <megous@xxxxxxxxxx> > > > > Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is > > called bcm43356 and can be used with the brcmfmac driver. The module > > is powered by the two always on regulators (not AXP805). > > > > WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be > > configured so that it sets up an 1.8V input bias on this port. This is > > done by the pio driver by reading the vcc-pg-supply voltage. > > > > You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt > > configuration that can be found in the Xulongs's repository for H6: > > > > https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256 > > > > Mainline brcmfmac driver expects the firmware and nvram at the > > following paths relative to the firmware directory: > > > > brcm/brcmfmac43456-sdio.bin > > brcm/brcmfmac43456-sdio.txt > > > > Signed-off-by: Ondrej Jirman <megous@xxxxxxxxxx> > > --- > > .../dts/allwinner/sun50i-h6-orangepi-3.dts | 48 +++++++++++++++++++ > > 1 file changed, 48 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > > index 5270142527f5..6a201829bb62 100644 > > --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > > @@ -66,6 +66,26 @@ > > regulator-always-on; > > }; > > > > + reg_vcc33_wifi: vcc33-wifi { > > + /* Always on 3.3V regulator for WiFi and BT */ > > + compatible = "regulator-fixed"; > > + regulator-name = "vcc33-wifi"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-always-on; > > + vin-supply = <®_vcc5v>; > > + }; > > + > > + reg_vcc_wifi_io: vcc-wifi-io { > > + /* Always on 1.8V/300mA regulator for WiFi and BT IO */ > > + compatible = "regulator-fixed"; > > + regulator-name = "vcc-wifi-io"; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-always-on; > > + vin-supply = <®_vcc33_wifi>; > > + }; > > + > > /* > > * The board uses 2.5V RGMII signalling. Power sequence > > * to enable the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2) > > @@ -86,6 +106,14 @@ > > */ > > vin-supply = <®_aldo2>; /* GMAC-3V3 */ > > }; > > + > > + wifi_pwrseq: wifi_pwrseq { > > + compatible = "mmc-pwrseq-simple"; > > + clocks = <&rtc 1>; > > Maybe I missed something, but the RTC in H6 is not yet available : > https://lkml.org/lkml/2018/10/31/822 You're right. I'm using an out-of-tree patch for that and didn't notice the dependency. I guess, WiFi DTS patch can be ignored for now. thanks, o. > Regards, > Clement > > > + clock-names = "ext_clock"; > > + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */ > > + post-power-on-delay-ms = <200>; > > + }; > > }; > > > > &cpu0 { > > @@ -146,6 +174,25 @@ > > status = "okay"; > > }; > > > > +&mmc1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc1_pins>; > > + vmmc-supply = <®_vcc33_wifi>; > > + vqmmc-supply = <®_vcc_wifi_io>; > > + mmc-pwrseq = <&wifi_pwrseq>; > > + bus-width = <4>; > > + non-removable; > > + status = "okay"; > > + > > + brcm: sdio-wifi@1 { > > + reg = <1>; > > + compatible = "brcm,bcm4329-fmac"; > > + interrupt-parent = <&r_pio>; > > + interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */ > > + interrupt-names = "host-wake"; > > + }; > > +}; > > + > > &ohci0 { > > status = "okay"; > > }; > > @@ -157,6 +204,7 @@ > > &pio { > > vcc-pc-supply = <®_bldo2>; > > vcc-pd-supply = <®_cldo1>; > > + vcc-pg-supply = <®_vcc_wifi_io>; > > }; > > > > &r_i2c { > > -- > > 2.21.0 > > > > -- > > You received this message because you are subscribed to the Google Groups "linux-sunxi" group. > > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxx. > > For more options, visit https://groups.google.com/d/optout.
