Hello, I apologize in advance, I am new to posting on here. I am trying to use the radio Sparklan WPEQ-160ACN(BT) (USB only, no PCIe) on an embedded ARM SBC. The card is detected in lsusb but does not create an interface in /sys/class/net. I don't see anything in the logs that ath10k tried to load any firmware, etc. The current wiki says that usb is not supported. (https://wireless.wiki.kernel.org/en/users/drivers/ath10k#not_supported) Is the wiki still correct? Thank you, Ryan Logs and info below: root@bionic-armhf:~# lsusb Bus 001 Device 003: ID 0cf3:9378 Atheros Communications, Inc. Bus 001 Device 002: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@bionic-armhf:~# uname -a Linux bionic-armhf 4.20.7-gaf078a3 #1 SMP Wed Feb 13 17:42:49 PST 2019 armv7l armv7l armv7l GNU/Linux root@bionic-armhf:~# ls /sys/class/net/ can0 enp8s0 eth0 lo root@bionic-armhf:~# dmesg | grep ath root@bionic-armhf:~# dmesg | grep usb [ 0.201196] usbcore: registered new interface driver usbfs [ 0.201386] usbcore: registered new interface driver hub [ 0.201713] usbcore: registered new device driver usb [ 3.756564] usbcore: registered new interface driver usb-storage [ 3.766381] imx_usb 2184000.usb: Linked as a consumer to regulator.10 [ 3.782126] imx_usb 2184200.usb: Linked as a consumer to regulator.9 [ 3.834669] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20 [ 3.843208] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.850519] usb usb1: Product: EHCI Host Controller [ 3.855420] usb usb1: Manufacturer: Linux 4.20.7-gaf078a3 ehci_hcd [ 3.861673] usb usb1: SerialNumber: ci_hdrc.1 [ 4.228010] usb usb1-port1: over-current condition [ 4.588013] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 4.669721] usb_otg_vbus: disabling [ 4.808872] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3 [ 4.817185] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 5.157790] usb 1-1.2: new high-speed USB device number 3 using ci_hdrc [ 5.320105] usb 1-1.2: New USB device found, idVendor=0cf3, idProduct=9378, bcdDevice= 3.00 [ 5.328545] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5.335877] usb 1-1.2: Product: USBWLAN [ 5.339783] usb 1-1.2: Manufacturer: Qualcomm Atheros [ 5.344856] usb 1-1.2: SerialNumber: 12345678 root@bionic-armhf:~# root@bionic-armhf:~# ls /lib/firmware/ath10k/QCA9377/hw1.0/ board-2.bin board.bin firmware-5.bin notice_ath10k_firmware-5.txt
