From: Ben Greear <greearb@xxxxxxxxxxxxxxx>
Firmware already supports this, so just enable the path
to configure the vdev parameter.
One potential issue: The firmware (10.1 at least) defaults to 2,
and the mac80211 stack defaults to 4. So applying this patch would
change the firmware behaviour regardless of user settings.
I verified this tweaked the proper firmware setting when I
ran this command:
iw phy wiphy0 set retry short 2 long 2
Signed-off-by: Ben Greear <greearb@xxxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/ath10k/mac.c | 31 +++++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath10k/wmi.c | 2 +-
drivers/net/wireless/ath/ath10k/wmi.h | 2 ++
3 files changed, 34 insertions(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index c90c8bb..b458e5b 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -2027,6 +2027,16 @@ static int ath10k_mac_vif_setup_ps(struct ath10k_vif *arvif)
return 0;
}
+static int ath10k_mac_vif_config_retry_limit(struct ath10k_vif *arvif, int limit)
+{
+ struct ath10k *ar = arvif->ar;
+ int vdev_param = ar->wmi.vdev_param->rc_num_retries;
+
+ lockdep_assert_held(&arvif->ar->conf_mutex);
+
+ return ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, limit);
+}
+
static int ath10k_mac_vif_disable_keepalive(struct ath10k_vif *arvif)
{
struct ath10k *ar = arvif->ar;
@@ -5516,6 +5526,24 @@ static int ath10k_config_ps(struct ath10k *ar)
return ret;
}
+static int ath10k_config_retry_limit(struct ath10k *ar, int limit)
+{
+ struct ath10k_vif *arvif;
+ int ret = 0;
+
+ lockdep_assert_held(&ar->conf_mutex);
+
+ list_for_each_entry(arvif, &ar->arvifs, list) {
+ ret = ath10k_mac_vif_config_retry_limit(arvif, limit);
+ if (ret) {
+ ath10k_warn(ar, "failed to setup retry-limit: %d\n", ret);
+ break;
+ }
+ }
+
+ return ret;
+}
+
static int ath10k_mac_txpower_setup(struct ath10k *ar, int txpower)
{
int ret;
@@ -5592,6 +5620,9 @@ static int ath10k_config(struct ieee80211_hw *hw, u32 changed)
ath10k_warn(ar, "failed to recalc monitor: %d\n", ret);
}
+ if (changed & IEEE80211_CONF_CHANGE_RETRY_LIMITS)
+ ret = ath10k_config_retry_limit(ar, conf->long_frame_max_tx_count);
+
mutex_unlock(&ar->conf_mutex);
return ret;
}
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 6aaa439..816883d 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -874,7 +874,7 @@ static struct wmi_vdev_param_map wmi_10x_vdev_param_map = {
.tx_encap_type = WMI_VDEV_PARAM_UNSUPPORTED,
.ap_detect_out_of_sync_sleeping_sta_time_secs =
WMI_10X_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS,
- .rc_num_retries = WMI_VDEV_PARAM_UNSUPPORTED,
+ .rc_num_retries = WMI_10X_VDEV_PARAM_RC_NUM_RETRIES,
.cabq_maxdur = WMI_VDEV_PARAM_UNSUPPORTED,
.mfptest_set = WMI_VDEV_PARAM_UNSUPPORTED,
.rts_fixed_rate = WMI_VDEV_PARAM_UNSUPPORTED,
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index 95ff280..b01778e 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -5369,6 +5369,8 @@ enum wmi_10x_vdev_param {
WMI_10X_VDEV_PARAM_MCAST2UCAST_SET,
/* Enable/Disable RTS-CTS */
WMI_10X_VDEV_PARAM_ENABLE_RTSCTS,
+ /** Total number of HW retries */
+ WMI_10X_VDEV_PARAM_RC_NUM_RETRIES,
WMI_10X_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS,
--
2.4.11
