On Thu, 2018-06-28 at 09:28 +0000, Kalle Valo wrote: > Ryan Hsu <ryanhsu@xxxxxxxxxxxxxx> wrote: > > > In the case of Station connects to AP with narrower bandwidth at > > beginning. > > And later the AP changes the bandwidth to winder bandwidth, the AP > > will > > beacon with wider bandwidth IE, eg VHT20->VHT40->VHT80 or VHT40- > > >VHT80. > > > > Since the supported BANDWIDTH will be limited by the PHYMODE, so > > while > > Station receives the bandwidth change request, it will also need to > > reconfigure the PHYMODE setting to firmware instead of just > > configuring > > the BANDWIDTH info, otherwise it'll trigger a firmware crash with > > non-support bandwidth. > > > > The issue was observed in WLAN.RM.4.4.1-00051-QCARMSWP-1, QCA6174 > > with > > below scenario: > > > > AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 > > MHz) > > disconnect from AP xxx for new auth to yyy > > RX ReassocResp from xxx (capab=0x1111 status=0 aid=102) > > associated > > > > .... > > > > AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 > > MHz) > > AP xxx changed bandwidth, new config is 5200 MHz, width 3 (5210/0 > > MHz) > > > > .... > > > > firmware register dump: > > [00]: 0x05030000 0x000015B3 0x00987291 0x00955B31 > > [04]: 0x00987291 0x00060730 0x00000004 0x00000001 > > [08]: 0x004089F0 0x00955A00 0x000A0B00 0x00400000 > > [12]: 0x00000009 0x00000000 0x00952CD0 0x00952CE6 > > [16]: 0x00952CC4 0x0098E25F 0x00000000 0x0091080D > > [20]: 0x40987291 0x0040E7A8 0x00000000 0x0041EE3C > > [24]: 0x809ABF05 0x0040E808 0x00000000 0xC0987291 > > [28]: 0x809A650C 0x0040E948 0x0041FE40 0x004345C4 > > [32]: 0x809A5C63 0x0040E988 0x0040E9AC 0x0042D1A8 > > [36]: 0x8091D252 0x0040E9A8 0x00000002 0x00000001 > > [40]: 0x809FDA9D 0x0040EA58 0x0043D554 0x0042D554 > > [44]: 0x809F8B22 0x0040EA78 0x0043D554 0x00000001 > > [48]: 0x80911210 0x0040EAC8 0x00000010 0x004041D0 > > [52]: 0x80911154 0x0040EB28 0x00400000 0x00000000 > > [56]: 0x8091122D 0x0040EB48 0x00000000 0x00400600 > > > > Reported-by: Rouven Czerwinski <rouven@xxxxxxxxxxxxxx> > > Tested-by: Timur Kristóf <timur.kristof@xxxxxxxxx> > > Signed-off-by: Ryan Hsu <ryanhsu@xxxxxxxxxxxxxx> > > Signed-off-by: Kalle Valo <kvalo@xxxxxxxxxxxxxx> > > Patch applied to ath-current branch of ath.git, thanks. > > 9191fc2a431b ath10k: update the phymode along with bandwidth change > request Thank you Kalle. Does this mean that the patch will get into kernel 4.18? Best regards, Tim
