kabe@xxxxxxxxxxxxxxxx wrote: > From: Taketo Kabe <kabe@xxxxxxxxxxxxxxxx> > > Fix for b43 wireless card stopping transmission when switching VTs. > > Setup: > Using BCM4306 rev.03 chip based CardBus wireless card. > IRQ is shared with yenta (cardbus bridge) and i915 (display) driver. > For firmware, installed latest but dated openfwwf 5.2 > (http://netweb.ing.unibs.it/~openfwwf/) > > How-to-reproduce: > Do "ssh <NetBSD-remotehost>", then "ls -lR /" to generate traffic, then > repeatedly switch VTs by Alt-F1<>Alt-F2. > Eventually (within a minute) the card stops working. > You can receive traffic but no transmission. > For unknown reason it doesn't occur when just generating traffic by > "ssh <remotehost> ls -lR /". > > With CONFIG_B43_DEBUG=y kernel config, when it stops, > the debug message shows > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 148, but got 180 > The slot offset I observed so far was always 32. > > When err_out2 is not set to make error messages successive, > the debug output will be like this: > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 148 > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 150 > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 120 > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 152 > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 122 > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 154 > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 124 > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 156 > kernel: b43-phy1 debug: Out of order TX status report on DMA ring 1. Expected 116, but got 126 > The TX ring alternates between 2 sequences; the ring seems > to be completely confused. Controller restart is needed. > > Workaround(1): > This problem doesn't occur when using propriatory firmware > you will extract by b43-fwcutter, so it may be a bug in > openfwwf firmware, as the comment in the b43_dma_handle_txstatus() suggests. > I wasn't able to find a bug in the terse openfwwf code though. > > Workaround(2): > Using "pio=1" option to not use DMA makes this problem to > not occur. > > Description of the patch: > This patch will forcibly reset the controller to make it > work again. Very kludgy and doesn't look right, but > the traffic will continue to flow. > > Signed-off-by: Taketo Kabe <kabe@xxxxxxxxxxxxxxxx> > Reviewed-by: Michael Buesch <m@xxxxxxx> > [kvalo@xxxxxxxxxxxxxx: clean up commit log] Failed to apply to wireless-drivers-next: fatal: sha1 information is lacking or useless (drivers/net/wireless/broadcom/b43/dma.c). error: could not build fake ancestor Applying: b43: fix transmit failure when VT is switched Patch failed at 0001 b43: fix transmit failure when VT is switched The copy of the patch that failed is found in: .git/rebase-apply/patch Please read: https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches#format_of_patches Also the change log should be after --- line: https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches#changelog_missing Patch set to Changes Requested. -- https://patchwork.kernel.org/patch/10391617/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches