Hello,
My new laptop apparently has a Real Tek R8822BE as the wifi device. The
module loads but I can not bring up the interface or do anything with
it. I think the problem is that the firmware load fails, see below. I
can not find any source for the listed firmware file or any make rules
to build it. Possibly connected, the machine also has an R8822B as the
Bluetooth device (possibly a secondary port on the same device?) which
shows the same error. The problem is not higher up in the networking
stack as eth0 works fine.
Any help will be appreciated.
Relevant (I think) info:
uname -a:
Linux IceFalcon 4.14.13-tuned #1 SMP Tue Jan 16 20:35:41 PST 2018 x86_64
Intel(R) Core(TM) i7-7700HQ CPU @ 2.80GHz GenuineIntel GNU/Linux
ifconfig wlan0:
wlan0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether d4:6a:6a:55:89:39 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ifconfig wlan0 up:
SIOCSIFFLAGS: Operation not permitted
lspci -v:
3c:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device b822
Subsystem: Hewlett-Packard Company Device 831b
Flags: bus master, fast devsel, latency 0, IRQ 131
I/O ports at c000 [size=256]
Memory at dc200000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [148] Device Serial Number 00-e0-4c-ff-fe-b8-22-01
Capabilities: [158] Latency Tolerance Reporting
Capabilities: [160] L1 PM Substates
Kernel driver in use: r8822be
Kernel modules: r8822be
dmesg:
[ 0.259212] pci 0000:3c:00.0: reg 0x10: [io 0xc000-0xc0ff]
[ 0.259235] pci 0000:3c:00.0: reg 0x18: [mem 0xdc200000-0xdc20ffff 64bit]
[ 0.259352] pci 0000:3c:00.0: supports D1 D2
[ 0.259353] pci 0000:3c:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.337550] pci_bus 0000:3c: resource 0 [io 0xc000-0xcfff]
[ 0.337551] pci_bus 0000:3c: resource 1 [mem 0xdc200000-0xdc2fffff]
[ 2.148955] r8822be: module is from the staging directory, the
quality is unknown, you have been warned.
[ 2.173850] r8822be 0000:3c:00.0: enabling device (0000 -> 0003)
[ 2.191530] r8822be: Using firmware rtlwifi/rtl8822befw.bin
[ 2.193717] r8822be 0000:3c:00.0: Direct firmware load for
rtlwifi/rtl8822befw.bin failed with error -2
[ 2.194503] r8822be: Selected firmware is not available
[ 2.195025] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 2.195321] r8822be: rtlwifi: wireless switch is on
[ 76.465245] r8822be: halmac_init_hal failed
[ 90.520215] r8822be: halmac_init_hal failed
[ 109.066224] r8822be: halmac_init_hal failed
[ 109.066486] r8822be: halmac_init_hal failed
[ 136.083957] r8822be: halmac_init_hal failed
[ 136.084197] r8822be: halmac_init_hal failed
[ 150.523513] r8822be: halmac_init_hal failed
[ 273.431684] r8822be: halmac_init_hal failed
