Search Linux Wireless

Re: brcmfmac: set p2p_disc error on BCM4350

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello Arend,

Did you had the chance to look into this?

On Mon, Jan 08, 2018 at 11:30:12AM +0100, William Dauchy wrote:
> Hello Arend,
> 
> Thanks for your quick answer.
> 
> On Mon, Jan 08, 2018 at 10:31:52AM +0100, Arend van Spriel wrote:
> > This has been reported before, but not been able to look into it. Diving
> > into firmware it seems that error can only occur if the mac address for the
> > p2pdev interface is already used. So if possible can you rebuild the driver
> > with the patch below applied and provide dmesg output and output of
> > 'ifconfig -a'.
> > 
> > Regards,
> > Arend
> > ---8<----------------------------------------------------------------
> > 
> > diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c
> > b/drivers/n
> > index 2ee5413..f96ad37 100644
> > --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c
> > +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c
> > @@ -2065,6 +2065,7 @@ static struct wireless_dev
> > *brcmf_p2p_create_p2pdev(struc
> >         int err;
> >         u32 bsscfgidx;
> > 
> > +       brcmf_err("enter: mac=%pM\n", addr);
> >         if (p2p->bss_idx[P2PAPI_BSSCFG_DEVICE].vif)
> >                 return ERR_PTR(-ENOSPC);
> > 
> >
> 
> Here is my brcmfmac dmesg output with patch applied
> (please tell me if you need complete dmesg)
> 
> brcmfmac: brcmf_fw_map_chip_to_name: using brcm/brcmfmac4350-pcie.bin for chip 0x004350(17232) rev 0x000008
> brcmfmac 0000:3a:00.0: Direct firmware load for brcm/brcmfmac4350-pcie.txt failed with error -2
> brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Oct 22 2015 06:16:26 version 7.35.180.119 (r594535) FWID 01-e791c176
> brcmfmac 0000:3a:00.0 wlp58s0: renamed from wlan0
> brcmfmac: brcmf_p2p_create_p2pdev: enter: mac=00:00:00:00:00:00
> brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
> brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlp58s0 type 10 failed: err=-16
> 
> ifconfig shows:
> 
> wlp58s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
>         inet 192.168.18.77  netmask 255.255.255.0  broadcast 192.168.18.255
>         inet6 fe80::3517:e1be:5bc7:899  prefixlen 64  scopeid 0x20<link>
>         ether 30:52:cb:83:71:33  txqueuelen 1000  (Ethernet)
>         RX packets 26557  bytes 34149730 (32.5 MiB)
>         RX errors 0  dropped 0  overruns 0  frame 0
>         TX packets 14965  bytes 2298777 (2.1 MiB)
>         TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

Best,
-- 
William



[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Wireless Regulations]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux