Many chips support channels in licensed bands. Add support for those,
along with a corresponding kernel config option to disable them by
default. Note that these channels are not selectable even if the
option has been compiled unless the user modifies the regulatory
database to explicitly enable the corresponding channels.
NOTE: These channels must not be used in most regulatory
domains unless you have a license from the FCC or similar!
Signed-off-by: Simon Wunderlich <sw@xxxxxxxxxxxxxxxxxx>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@xxxxxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/ath10k/Kconfig | 20 ++++++++++++++++++++
drivers/net/wireless/ath/ath10k/core.h | 4 ++++
drivers/net/wireless/ath/ath10k/mac.c | 9 +++++++++
drivers/net/wireless/ath/ath10k/wmi.c | 7 +++++--
4 files changed, 38 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/Kconfig b/drivers/net/wireless/ath/ath10k/Kconfig
index b4241cf9b7ed..13a23ed33f91 100644
--- a/drivers/net/wireless/ath/ath10k/Kconfig
+++ b/drivers/net/wireless/ath/ath10k/Kconfig
@@ -53,3 +53,23 @@ config ATH10K_DFS_CERTIFIED
---help---
This option enables DFS support for initiating radiation on
ath10k.
+
+config ATH10K_LICENSED_CHAN
+ bool "Support channels in licensed bands"
+ depends on ATH10K && CFG80211_CERTIFICATION_ONUS
+ default n
+ ---help---
+ This option enables support for licensed channels on such as
+ 4.9 GHz (public safety).
+
+ These are PUBLIC SAFETY CHANNELS and MUST NOT BE USED in most
+ regulatory domains UNLESS YOU HAVE A FULL LICENSE for their use from
+ your local radio regulator, e.g. the FCC or equivalent. Using these
+ channels without proper authorisation may result in serious legal
+ consequences.
+
+ You will also have to build a regulatory database with these channels
+ enabled to actually use them.
+
+ If you are a distro kernel builder or have any doubt whatsoever about
+ your legal ability to use these channels, say N.
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index d4b9a0ec1bdc..7674641537b4 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -46,7 +46,11 @@
#define WMI_READY_TIMEOUT (5 * HZ)
#define ATH10K_FLUSH_TIMEOUT_HZ (5 * HZ)
#define ATH10K_CONNECTION_LOSS_HZ (3 * HZ)
+#ifdef CONFIG_ATH10K_LICENSED_CHAN
+#define ATH10K_NUM_CHANS 47
+#else
#define ATH10K_NUM_CHANS 40
+#endif
/* Antenna noise floor */
#define ATH10K_DEFAULT_NOISE_FLOOR -95
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index a25f0ec15cf8..23895af0fc63 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -7669,6 +7669,15 @@ static const struct ieee80211_channel ath10k_5ghz_channels[] = {
CHAN5G(161, 5805, 0),
CHAN5G(165, 5825, 0),
CHAN5G(169, 5845, 0),
+#ifdef CONFIG_ATH10K_LICENSED_CHAN
+ CHAN5G(184, 4920, 0),
+ CHAN5G(188, 4940, 0),
+ CHAN5G(192, 4960, 0),
+ CHAN5G(196, 4980, 0),
+ CHAN5G(8, 5040, 0),
+ CHAN5G(12, 5060, 0),
+ CHAN5G(16, 5080, 0),
+#endif
};
struct ath10k *ath10k_mac_create(size_t priv_size)
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 4e60caec7ab4..de7a4fa9d347 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -2323,10 +2323,13 @@ int ath10k_wmi_event_mgmt_rx(struct ath10k *ar, struct sk_buff *skb)
/* Hardware can Rx CCK rates on 5GHz. In that case phy_mode is set to
* MODE_11B. This means phy_mode is not a reliable source for the band
* of mgmt rx.
+ *
+ * On the other hand, channel 8, 12 and 16 are defined in 5GHz as well
+ * (5040 - 5080 MHz), therefore apply the override only for channels <=7
*/
- if (channel >= 1 && channel <= 14) {
+ if (channel >= 1 && channel <= 7) {
status->band = NL80211_BAND_2GHZ;
- } else if (channel >= 36 && channel <= 169) {
+ } else if (channel >= 8 && channel <= 196) {
status->band = NL80211_BAND_5GHZ;
} else {
/* Shouldn't happen unless list of advertised channels to
--
2.11.0
