Michal Kazior <michal.kazior@xxxxxxxxx> writes: > On 13 December 2016 at 14:44, Valo, Kalle <kvalo@xxxxxxxxxxxxxxxx> wrote: >> Erik Stromdahl <erik.stromdahl@xxxxxxxxx> writes: >> >>> Code refactorization: >>> >>> Moved the code for ep 0 in ath10k_htc_rx_completion_handler >>> to ath10k_htc_control_rx_complete. >>> >>> This eases the implementation of SDIO/mbox significantly since >>> the ep_rx_complete cb is invoked directly from the SDIO/mbox >>> hif layer. >>> >>> Since the ath10k_htc_control_rx_complete already is present >>> (only containing a warning message) there is no reason for not >>> using it (instead of having a special case for ep 0 in >>> ath10k_htc_rx_completion_handler). >>> >>> Signed-off-by: Erik Stromdahl <erik.stromdahl@xxxxxxxxx> >> >> I tested this on QCA988X PCI board just to see if there are any >> regressions. It crashes immediately during module load, every time, and >> bisected that the crashing starts on this patch: >> >> [ 1239.715325] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 >> [ 1239.885125] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2 >> [ 1239.885260] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2 >> [ 1239.885687] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000 >> [ 1239.885699] ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1 >> [ 1239.885899] ath10k_pci 0000:02:00.0: firmware ver 10.2.4.70.59-2 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 4159f498 >> [ 1239.941836] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2 >> [ 1239.941993] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 >> [ 1241.136693] BUG: unable to handle kernel NULL pointer dereference at (null) >> [ 1241.136738] IP: [< (null)>] (null) >> [ 1241.136759] *pdpt = 0000000000000000 *pde = f0002a55f0002a55 [ 1241.136781] >> [ 1241.136793] Oops: 0010 [#1] SMP >> >> What's odd is that when I added some printks on my own and enabled both >> boot and htc debug levels it doesn't crash anymore. After everything >> works normally after that, I can start AP mode and connect to it. Is it >> a race somewhere? > > Yes. htc_wait_target() is called after hif_start(). The ep_rx_complete > is set in htc_wait_target() [changed patch 4, but still too late]. > > ep_rx_complete must be set prior to calling hif_start(). You probably > crash on end of ath10k_htc_rx_completion_handler() when trying to call > ep->ep_ops.ep_rx_complete(ar, skb). Yeah, just checked and ep->ep_ops.ep_rx_complete is NULL at the end of ath10k_htc_rx_completion_handler(). -- Kalle Valo
