This is to prepare for rx descriptor abstraction where we'll
be dereferencing ath10k_hw_params member in hw.h. Moreover
hw.h looks more suitable to house ath10k_hw_params definition
than core.h
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@xxxxxxxxxxxxxxxx>
---
drivers/net/wireless/ath/ath10k/core.h | 48 +---------------------------------
drivers/net/wireless/ath/ath10k/hw.h | 48 ++++++++++++++++++++++++++++++++++
2 files changed, 49 insertions(+), 47 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 30ae5bf..5ace413 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -715,53 +715,7 @@ struct ath10k {
struct ath10k_htc htc;
struct ath10k_htt htt;
- struct ath10k_hw_params {
- u32 id;
- u16 dev_id;
- const char *name;
- u32 patch_load_addr;
- int uart_pin;
- u32 otp_exe_param;
-
- /* Type of hw cycle counter wraparound logic, for more info
- * refer enum ath10k_hw_cc_wraparound_type.
- */
- enum ath10k_hw_cc_wraparound_type cc_wraparound_type;
-
- /* Some of chip expects fragment descriptor to be continuous
- * memory for any TX operation. Set continuous_frag_desc flag
- * for the hardware which have such requirement.
- */
- bool continuous_frag_desc;
-
- /* CCK hardware rate table mapping for the newer chipsets
- * like QCA99X0, QCA4019 got revised. The CCK h/w rate values
- * are in a proper order with respect to the rate/preamble
- */
- bool cck_rate_map_rev2;
-
- u32 channel_counters_freq_hz;
-
- /* Mgmt tx descriptors threshold for limiting probe response
- * frames.
- */
- u32 max_probe_resp_desc_thres;
-
- /* The padding bytes's location is different on various chips */
- enum ath10k_hw_4addr_pad hw_4addr_pad;
-
- u32 tx_chain_mask;
- u32 rx_chain_mask;
- u32 max_spatial_stream;
- u32 cal_data_len;
-
- struct ath10k_hw_params_fw {
- const char *dir;
- const char *board;
- size_t board_size;
- size_t board_ext_size;
- } fw;
- } hw_params;
+ struct ath10k_hw_params hw_params;
/* contains the firmware images used with ATH10K_FIRMWARE_MODE_NORMAL */
struct ath10k_fw_components normal_mode_fw;
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index e014cd7..1315557 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -363,6 +363,54 @@ enum ath10k_hw_cc_wraparound_type {
ATH10K_HW_CC_WRAP_SHIFTED_EACH = 2,
};
+struct ath10k_hw_params {
+ u32 id;
+ u16 dev_id;
+ const char *name;
+ u32 patch_load_addr;
+ int uart_pin;
+ u32 otp_exe_param;
+
+ /* Type of hw cycle counter wraparound logic, for more info
+ * refer enum ath10k_hw_cc_wraparound_type.
+ */
+ enum ath10k_hw_cc_wraparound_type cc_wraparound_type;
+
+ /* Some of chip expects fragment descriptor to be continuous
+ * memory for any TX operation. Set continuous_frag_desc flag
+ * for the hardware which have such requirement.
+ */
+ bool continuous_frag_desc;
+
+ /* CCK hardware rate table mapping for the newer chipsets
+ * like QCA99X0, QCA4019 got revised. The CCK h/w rate values
+ * are in a proper order with respect to the rate/preamble
+ */
+ bool cck_rate_map_rev2;
+
+ u32 channel_counters_freq_hz;
+
+ /* Mgmt tx descriptors threshold for limiting probe response
+ * frames.
+ */
+ u32 max_probe_resp_desc_thres;
+
+ /* The padding bytes's location is different on various chips */
+ enum ath10k_hw_4addr_pad hw_4addr_pad;
+
+ u32 tx_chain_mask;
+ u32 rx_chain_mask;
+ u32 max_spatial_stream;
+ u32 cal_data_len;
+
+ struct ath10k_hw_params_fw {
+ const char *dir;
+ const char *board;
+ size_t board_size;
+ size_t board_ext_size;
+ } fw;
+};
+
/* Target specific defines for MAIN firmware */
#define TARGET_NUM_VDEVS 8
#define TARGET_NUM_PEER_AST 2
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
