From: Jes Sorensen <Jes.Sorensen@xxxxxxxxxx>
The 8723bu is a combo WiFi/BT dongle, and path B is not used for WiFi,
so no point in calibrating it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@xxxxxxxxxx>
---
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 76 +-----------------------
1 file changed, 3 insertions(+), 73 deletions(-)
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 71d375c..c355d27 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -4988,50 +4988,6 @@ out:
return result;
}
-#ifdef RTL8723BU_PATH_B
-static int rtl8723bu_iqk_path_b(struct rtl8xxxu_priv *priv)
-{
- u32 reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc, path_sel;
- int result = 0;
-
- path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH);
-
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- /* One shot, path B LOK & IQK */
- rtl8xxxu_write32(priv, REG_IQK_AGC_CONT, 0x00000002);
- rtl8xxxu_write32(priv, REG_IQK_AGC_CONT, 0x00000000);
-
- mdelay(1);
-
- /* Check failed */
- reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
- reg_eb4 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
- reg_ebc = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
- reg_ec4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_B_2);
- reg_ecc = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_B_2);
-
- if (!(reg_eac & BIT(31)) &&
- ((reg_eb4 & 0x03ff0000) != 0x01420000) &&
- ((reg_ebc & 0x03ff0000) != 0x00420000))
- result |= 0x01;
- else
- goto out;
-
- if (!(reg_eac & BIT(30)) &&
- (((reg_ec4 & 0x03ff0000) >> 16) != 0x132) &&
- (((reg_ecc & 0x03ff0000) >> 16) != 0x36))
- result |= 0x02;
- else
- dev_warn(&priv->udev->dev, "%s: Path B RX IQK failed!\n",
- __func__);
-out:
- return result;
-}
-#endif
-
static int rtl8192eu_iqk_path_a(struct rtl8xxxu_priv *priv)
{
u32 reg_eac, reg_e94, reg_e9c;
@@ -5619,20 +5575,6 @@ static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4);
rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000);
-#ifdef RTL8723BU_PATH_B
- /* Set RF mode to standby Path B */
- if (priv->tx_paths > 1)
- rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_AC, 0x10000);
-#endif
-
-#if 0
- /* Page B init */
- rtl8xxxu_write32(priv, REG_CONFIG_ANT_A, 0x0f600000);
-
- if (priv->tx_paths > 1)
- rtl8xxxu_write32(priv, REG_CONFIG_ANT_B, 0x0f600000);
-#endif
-
/*
* RX IQ calibration setting for 8723B D cut large current issue
* when leaving IPS
@@ -5662,12 +5604,6 @@ static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
val32 &= 0x000000ff;
rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-#if 0 /* Only needed in restore case, we may need this when going to suspend */
- priv->RFCalibrateInfo.TxLOK[RF_A] =
- rtl8xxxu_read_rfreg(priv, RF_A,
- RF6052_REG_TXM_IDAC);
-#endif
-
val32 = rtl8xxxu_read32(priv,
REG_TX_POWER_BEFORE_IQK_A);
result[t][0] = (val32 >> 16) & 0x3ff;
@@ -6209,15 +6145,9 @@ static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32);
rtl8xxxu_write_rfreg(priv, RF_A, 0x43, 0x300bd);
- if (priv->rf_paths > 1) {
- dev_dbg(dev, "%s: beware 2T not yet supported\n", __func__);
-#ifdef RTL8723BU_PATH_B
- if (RF_Path == 0x0) //S1
- ODM_SetIQCbyRFpath(pDM_Odm, 0);
- else //S0
- ODM_SetIQCbyRFpath(pDM_Odm, 1);
-#endif
- }
+ if (priv->rf_paths > 1)
+ dev_dbg(dev, "%s: 8723BU 2T not supported\n", __func__);
+
rtl8xxxu_prepare_calibrate(priv, 0);
}
--
2.5.5
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
