From: Jes Sorensen <Jes.Sorensen@xxxxxxxxxx>
8192eu has it's own IQK calibration procedure, and notably uses
undocumented RF register 0x56 in the process.
Signed-off-by: Jes Sorensen <Jes.Sorensen@xxxxxxxxxx>
---
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 608 ++++++++++++++++++++-
.../net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h | 1 +
2 files changed, 608 insertions(+), 1 deletion(-)
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 604deb4..61c0ece 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -4955,6 +4955,334 @@ out:
}
#endif
+static int rtl8192eu_iqk_path_a(struct rtl8xxxu_priv *priv)
+{
+ u32 reg_eac, reg_e94, reg_e9c;
+ int result = 0;
+
+ /*
+ * TX IQK
+ * PA/PAD controlled by 0x0
+ */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x00180);
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+ /* Path A IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82140303);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x68160000);
+
+ /* LO calibration setting */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00462911);
+
+ /* One shot, path A LOK & IQK */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+ mdelay(10);
+
+ /* Check failed */
+ reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+ reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
+ reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
+
+ if (!(reg_eac & BIT(28)) &&
+ ((reg_e94 & 0x03ff0000) != 0x01420000) &&
+ ((reg_e9c & 0x03ff0000) != 0x00420000))
+ result |= 0x01;
+
+ return result;
+}
+
+static int rtl8192eu_rx_iqk_path_a(struct rtl8xxxu_priv *priv)
+{
+ u32 reg_ea4, reg_eac, reg_e94, reg_e9c, val32;
+ int result = 0;
+
+ /* Leave IQK mode */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00);
+
+ /* Enable path A PA in TX IQK mode */
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, 0x800a0);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0000f);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf117b);
+
+ /* PA/PAD control by 0x56, and set = 0x0 */
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x00980);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_56, 0x51000);
+
+ /* Enter IQK mode */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+ /* TX IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+ rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+ /* path-A IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160c1f);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x68160c1f);
+
+ /* LO calibration setting */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911);
+
+ /* One shot, path A LOK & IQK */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+ mdelay(10);
+
+ /* Check failed */
+ reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+ reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
+ reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
+
+ if (!(reg_eac & BIT(28)) &&
+ ((reg_e94 & 0x03ff0000) != 0x01420000) &&
+ ((reg_e9c & 0x03ff0000) != 0x00420000)) {
+ result |= 0x01;
+ } else {
+ /* PA/PAD controlled by 0x0 */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x180);
+ goto out;
+ }
+
+ val32 = 0x80007c00 |
+ (reg_e94 & 0x03ff0000) | ((reg_e9c >> 16) & 0x03ff);
+ rtl8xxxu_write32(priv, REG_TX_IQK, val32);
+
+ /* Modify RX IQK mode table */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, 0x800a0);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0000f);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7ffa);
+
+ /* PA/PAD control by 0x56, and set = 0x0 */
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x00980);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_56, 0x51000);
+
+ /* Enter IQK mode */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+ /* IQK setting */
+ rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+ /* Path A IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x18008c1c);
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160c1f);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28160c1f);
+
+ /* LO calibration setting */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a891);
+
+ /* One shot, path A LOK & IQK */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+ mdelay(10);
+
+ reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+ reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2);
+
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x180);
+
+ if (!(reg_eac & BIT(27)) &&
+ ((reg_ea4 & 0x03ff0000) != 0x01320000) &&
+ ((reg_eac & 0x03ff0000) != 0x00360000))
+ result |= 0x02;
+ else
+ dev_warn(&priv->udev->dev, "%s: Path A RX IQK failed!\n",
+ __func__);
+
+out:
+ return result;
+}
+
+static int rtl8192eu_iqk_path_b(struct rtl8xxxu_priv *priv)
+{
+ u32 reg_eac, reg_eb4, reg_ebc;
+ int result = 0;
+
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x00180);
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+ /* Path B IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x18008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x821403e2);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x68160000);
+
+ /* LO calibration setting */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00492911);
+
+ /* One shot, path A LOK & IQK */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+ mdelay(1);
+
+ /* Check failed */
+ reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+ reg_eb4 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
+ reg_ebc = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
+
+ if (!(reg_eac & BIT(31)) &&
+ ((reg_eb4 & 0x03ff0000) != 0x01420000) &&
+ ((reg_ebc & 0x03ff0000) != 0x00420000))
+ result |= 0x01;
+ else
+ dev_warn(&priv->udev->dev, "%s: Path B IQK failed!\n",
+ __func__);
+
+ return result;
+}
+
+static int rtl8192eu_rx_iqk_path_b(struct rtl8xxxu_priv *priv)
+{
+ u32 reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc, val32;
+ int result = 0;
+
+ /* Leave IQK mode */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+
+ /* Enable path A PA in TX IQK mode */
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_WE_LUT, 0x800a0);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_RCK_OS, 0x30000);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_TXPA_G1, 0x0000f);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_TXPA_G2, 0xf117b);
+
+ /* PA/PAD control by 0x56, and set = 0x0 */
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x00980);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_56, 0x51000);
+
+ /* Enter IQK mode */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+ /* TX IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+ rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+ /* path-A IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x18008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82160c1f);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x68160c1f);
+
+ /* LO calibration setting */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911);
+
+ /* One shot, path A LOK & IQK */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+ mdelay(10);
+
+ /* Check failed */
+ reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+ reg_eb4 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
+ reg_ebc = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
+
+ if (!(reg_eac & BIT(31)) &&
+ ((reg_eb4 & 0x03ff0000) != 0x01420000) &&
+ ((reg_ebc & 0x03ff0000) != 0x00420000)) {
+ result |= 0x01;
+ } else {
+ /*
+ * PA/PAD controlled by 0x0
+ * Vendor driver restores RF_A here which I believe is a bug
+ */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x180);
+ goto out;
+ }
+
+ val32 = 0x80007c00 |
+ (reg_eb4 & 0x03ff0000) | ((reg_ebc >> 16) & 0x03ff);
+ rtl8xxxu_write32(priv, REG_TX_IQK, val32);
+
+ /* Modify RX IQK mode table */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_WE_LUT, 0x800a0);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_RCK_OS, 0x30000);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_TXPA_G1, 0x0000f);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_TXPA_G2, 0xf7ffa);
+
+ /* PA/PAD control by 0x56, and set = 0x0 */
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x00980);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_56, 0x51000);
+
+ /* Enter IQK mode */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+ /* IQK setting */
+ rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+ /* Path A IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x18008c1c);
+
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160c1f);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28160c1f);
+
+ /* LO calibration setting */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a891);
+
+ /* One shot, path A LOK & IQK */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xfa000000);
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+ mdelay(10);
+
+ reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+ reg_ec4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_B_2);
+ reg_ecc = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_B_2);
+
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+ rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_UNKNOWN_DF, 0x180);
+
+ if (!(reg_eac & BIT(30)) &&
+ ((reg_ec4 & 0x03ff0000) != 0x01320000) &&
+ ((reg_ecc & 0x03ff0000) != 0x00360000))
+ result |= 0x02;
+ else
+ dev_warn(&priv->udev->dev, "%s: Path B RX IQK failed!\n",
+ __func__);
+
+out:
+ return result;
+}
+
static void rtl8xxxu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
int result[][8], int t)
{
@@ -5385,6 +5713,194 @@ static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
}
}
+static void rtl8192eu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
+ int result[][8], int t)
+{
+ struct device *dev = &priv->udev->dev;
+ u32 i, val32;
+ int path_a_ok, path_b_ok;
+ int retry = 2;
+ const u32 adda_regs[RTL8XXXU_ADDA_REGS] = {
+ REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH,
+ REG_RX_WAIT_CCA, REG_TX_CCK_RFON,
+ REG_TX_CCK_BBON, REG_TX_OFDM_RFON,
+ REG_TX_OFDM_BBON, REG_TX_TO_RX,
+ REG_TX_TO_TX, REG_RX_CCK,
+ REG_RX_OFDM, REG_RX_WAIT_RIFS,
+ REG_RX_TO_RX, REG_STANDBY,
+ REG_SLEEP, REG_PMPD_ANAEN
+ };
+ const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = {
+ REG_TXPAUSE, REG_BEACON_CTRL,
+ REG_BEACON_CTRL_1, REG_GPIO_MUXCFG
+ };
+ const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = {
+ REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR,
+ REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B,
+ REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE,
+ REG_FPGA0_XB_RF_INT_OE, REG_CCK0_AFE_SETTING
+ };
+ u8 xa_agc = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1) & 0xff;
+ u8 xb_agc = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1) & 0xff;
+
+ /*
+ * Note: IQ calibration must be performed after loading
+ * PHY_REG.txt , and radio_a, radio_b.txt
+ */
+
+ if (t == 0) {
+ /* Save ADDA parameters, turn Path A ADDA on */
+ rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup,
+ RTL8XXXU_ADDA_REGS);
+ rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
+ rtl8xxxu_save_regs(priv, iqk_bb_regs,
+ priv->bb_backup, RTL8XXXU_BB_REGS);
+ }
+
+ rtl8xxxu_path_adda_on(priv, adda_regs, true);
+
+ /* MAC settings */
+ rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup);
+
+ val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING);
+ val32 |= 0x0f000000;
+ rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32);
+
+ rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600);
+ rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4);
+ rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22208200);
+
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_XAB_RF_SW_CTRL);
+ val32 |= (FPGA0_RF_PAPE | (FPGA0_RF_PAPE << FPGA0_RF_BD_CTRL_SHIFT));
+ rtl8xxxu_write32(priv, REG_FPGA0_XAB_RF_SW_CTRL, val32);
+
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_XA_RF_INT_OE);
+ val32 |= BIT(10);
+ rtl8xxxu_write32(priv, REG_FPGA0_XA_RF_INT_OE, val32);
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_XB_RF_INT_OE);
+ val32 |= BIT(10);
+ rtl8xxxu_write32(priv, REG_FPGA0_XB_RF_INT_OE, val32);
+
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+ rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+ rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+ for (i = 0; i < retry; i++) {
+ path_a_ok = rtl8192eu_iqk_path_a(priv);
+ if (path_a_ok == 0x01) {
+ val32 = rtl8xxxu_read32(priv,
+ REG_TX_POWER_BEFORE_IQK_A);
+ result[t][0] = (val32 >> 16) & 0x3ff;
+ val32 = rtl8xxxu_read32(priv,
+ REG_TX_POWER_AFTER_IQK_A);
+ result[t][1] = (val32 >> 16) & 0x3ff;
+
+ break;
+ }
+ }
+
+ if (!path_a_ok)
+ dev_dbg(dev, "%s: Path A TX IQK failed!\n", __func__);
+
+ for (i = 0; i < retry; i++) {
+ path_a_ok = rtl8192eu_rx_iqk_path_a(priv);
+ if (path_a_ok == 0x03) {
+ val32 = rtl8xxxu_read32(priv,
+ REG_RX_POWER_BEFORE_IQK_A_2);
+ result[t][2] = (val32 >> 16) & 0x3ff;
+ val32 = rtl8xxxu_read32(priv,
+ REG_RX_POWER_AFTER_IQK_A_2);
+ result[t][3] = (val32 >> 16) & 0x3ff;
+
+ break;
+ }
+ }
+
+ if (!path_a_ok)
+ dev_dbg(dev, "%s: Path A RX IQK failed!\n", __func__);
+
+ if (priv->rf_paths > 1) {
+ dev_warn(dev, "%s: Path B ongoing\n", __func__);
+
+ /* Path A into standby */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0x10000);
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+
+ /* Turn Path B ADDA on */
+ rtl8xxxu_path_adda_on(priv, adda_regs, false);
+
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x80800000);
+ rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+ rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+ for (i = 0; i < retry; i++) {
+ path_b_ok = rtl8192eu_iqk_path_b(priv);
+ if (path_b_ok == 0x01) {
+ val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
+ result[t][4] = (val32 >> 16) & 0x3ff;
+ val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
+ result[t][5] = (val32 >> 16) & 0x3ff;
+ break;
+ }
+ }
+
+ if (!path_b_ok)
+ dev_dbg(dev, "%s: Path B IQK failed!\n", __func__);
+
+ for (i = 0; i < retry; i++) {
+ path_b_ok = rtl8192eu_rx_iqk_path_b(priv);
+ if (path_a_ok == 0x03) {
+ val32 = rtl8xxxu_read32(priv,
+ REG_RX_POWER_BEFORE_IQK_B_2);
+ result[t][6] = (val32 >> 16) & 0x3ff;
+ val32 = rtl8xxxu_read32(priv,
+ REG_RX_POWER_AFTER_IQK_B_2);
+ result[t][7] = (val32 >> 16) & 0x3ff;
+ break;
+ }
+ }
+
+ if (!path_b_ok)
+ dev_dbg(dev, "%s: Path B RX IQK failed!\n", __func__);
+ }
+
+ /* Back to BB mode, load original value */
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, 0x00000000);
+
+ if (t) {
+ /* Reload ADDA power saving parameters */
+ rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup,
+ RTL8XXXU_ADDA_REGS);
+
+ /* Reload MAC parameters */
+ rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
+
+ /* Reload BB parameters */
+ rtl8xxxu_restore_regs(priv, iqk_bb_regs,
+ priv->bb_backup, RTL8XXXU_BB_REGS);
+
+ /* Restore RX initial gain */
+ val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1);
+ val32 &= 0xffffff00;
+ rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | 0x50);
+ rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | xa_agc);
+
+ if (priv->rf_paths > 1) {
+ val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1);
+ val32 &= 0xffffff00;
+ rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
+ val32 | 0x50);
+ rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
+ val32 | xb_agc);
+ }
+
+ /* Load 0xe30 IQC default value */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00);
+ }
+}
+
static void rtl8xxxu_prepare_calibrate(struct rtl8xxxu_priv *priv, u8 start)
{
struct h2c_cmd h2c;
@@ -5630,6 +6146,96 @@ static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
rtl8xxxu_prepare_calibrate(priv, 0);
}
+static void rtl8192eu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
+{
+ struct device *dev = &priv->udev->dev;
+ int result[4][8]; /* last is final result */
+ int i, candidate;
+ bool path_a_ok, path_b_ok;
+ u32 reg_e94, reg_e9c, reg_ea4, reg_eac;
+ u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc;
+ bool simu;
+
+ memset(result, 0, sizeof(result));
+ candidate = -1;
+
+ path_a_ok = false;
+ path_b_ok = false;
+
+ for (i = 0; i < 3; i++) {
+ rtl8192eu_phy_iqcalibrate(priv, result, i);
+
+ if (i == 1) {
+ simu = rtl8723bu_simularity_compare(priv, result, 0, 1);
+ if (simu) {
+ candidate = 0;
+ break;
+ }
+ }
+
+ if (i == 2) {
+ simu = rtl8723bu_simularity_compare(priv, result, 0, 2);
+ if (simu) {
+ candidate = 0;
+ break;
+ }
+
+ simu = rtl8723bu_simularity_compare(priv, result, 1, 2);
+ if (simu)
+ candidate = 1;
+ else
+ candidate = 3;
+ }
+ }
+
+ for (i = 0; i < 4; i++) {
+ reg_e94 = result[i][0];
+ reg_e9c = result[i][1];
+ reg_ea4 = result[i][2];
+ reg_eac = result[i][3];
+ reg_eb4 = result[i][4];
+ reg_ebc = result[i][5];
+ reg_ec4 = result[i][6];
+ reg_ecc = result[i][7];
+ }
+
+ if (candidate >= 0) {
+ reg_e94 = result[candidate][0];
+ priv->rege94 = reg_e94;
+ reg_e9c = result[candidate][1];
+ priv->rege9c = reg_e9c;
+ reg_ea4 = result[candidate][2];
+ reg_eac = result[candidate][3];
+ reg_eb4 = result[candidate][4];
+ priv->regeb4 = reg_eb4;
+ reg_ebc = result[candidate][5];
+ priv->regebc = reg_ebc;
+ reg_ec4 = result[candidate][6];
+ reg_ecc = result[candidate][7];
+ dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate);
+ dev_dbg(dev,
+ "%s: e94 =%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x "
+ "ecc=%x\n ", __func__, reg_e94, reg_e9c,
+ reg_ea4, reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc);
+ path_a_ok = true;
+ path_b_ok = true;
+ } else {
+ reg_e94 = reg_eb4 = priv->rege94 = priv->regeb4 = 0x100;
+ reg_e9c = reg_ebc = priv->rege9c = priv->regebc = 0x0;
+ }
+
+ if (reg_e94 && candidate >= 0)
+ rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result,
+ candidate, (reg_ea4 == 0));
+
+ if (priv->rf_paths > 1)
+ rtl8xxxu_fill_iqk_matrix_b(priv, path_b_ok, result,
+ candidate, (reg_ec4 == 0));
+
+ rtl8xxxu_save_regs(priv, rtl8723au_iqk_phy_iq_bb_reg,
+ priv->bb_recovery_backup, RTL8XXXU_BB_REGS);
+}
+
static void rtl8723a_phy_lc_calibrate(struct rtl8xxxu_priv *priv)
{
u32 val32;
@@ -9080,7 +9686,7 @@ static struct rtl8xxxu_fileops rtl8192eu_fops = {
.power_off = rtl8xxxu_power_off,
.reset_8051 = rtl8xxxu_reset_8051,
.llt_init = rtl8xxxu_auto_llt_table,
- .phy_iq_calibrate = rtl8723bu_phy_iq_calibrate,
+ .phy_iq_calibrate = rtl8192eu_phy_iq_calibrate,
.config_channel = rtl8723bu_config_channel,
.parse_rx_desc = rtl8723bu_parse_rx_desc,
.enable_rf = rtl8723b_enable_rf,
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
index c19f234..2aa14b1 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h
@@ -1130,6 +1130,7 @@
#define RF6052_REG_T_METER_8723B 0x42
#define RF6052_REG_UNKNOWN_43 0x43
#define RF6052_REG_UNKNOWN_55 0x55
+#define RF6052_REG_UNKNOWN_56 0x56
#define RF6052_REG_S0S1 0xb0
#define RF6052_REG_UNKNOWN_DF 0xdf
#define RF6052_REG_UNKNOWN_ED 0xed
--
2.5.5
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
