On Thu, Mar 17, 2016 at 1:55 AM, Michal Kazior <michal.kazior@xxxxxxxxx> wrote: > I suspect the BK/BE latency difference has to do with the fact that > there's bulk traffic going on BE queues (this isn't reflected > explicitly in the plots). The `bursts` flent test includes short > bursts of traffic on tid0 (BE) which is shared with ICMP and BE UDP_RR > (seen as green and blue lines on the plot). Due to (intended) limited > outflow (6mbps) BE queues build up and don't drain for the duration of > the entire test creating more opportunities for aggregating BE traffic > while other queues are near-empty and very short (time wise as well). I agree with your explanation. Access to the media and queue length are the two variables at play here. I just committed a new flent test that should exercise the vo,vi,be, and bk queues, "bursts_11e". I dropped the conventional ping from it and just rely on netperf's udp_rr for each queue. It seems to "do the right thing" on the ath9k.... And while I'm all in favor of getting 802.11e's behaviors more right, and this seems like a good way to get there... netperf's udp_rr is not how much traffic conventionally behaves. It doesn't do tcp slow start or congestion control in particular... In the case of the VO queue, for example, the (2004) intended behavior was 1 isochronous packet per 10ms per voice sending station and one from the ap, not a "ping". And at the time, VI was intended to be unicast video. TCP was an afterthought. (wifi's original (1993) mac was actually designed for ipx/spx!) I long for regular "rrul" and "rrul_be" tests against the new stuff to blow it up thoroughly as references along the way. (tcp_upload, tcp_download, (and several of the rtt_fair tests also between stations)). Will get formal about it here as soon as we end up on the same kernel trees.... Furthermore 802.11e is not widely used - in particular, not much internet bound/sourced traffic falls into more than BE and BK, presently. and in some cases weirder - comcast remarks a very large percentage of to the home inbound traffic as CS1 (BK), btw, and stations tend to use CS0. Data comes in on BK, acks go out on BE. I/we will try to come up with intermediate tests between the burst tests and the rrul tests as we go along the way. > If you consider Wi-Fi is half-duplex and latency in the entire stack In the context of this test regime... <pedantry> Saying wifi is "half"-duplex is a misleading way to think about it in many respects. it is a shared medium more like early, non-switched ethernet, with a weird mac that governs what sort of packets get access to (a txop) the medium first, across all stations co-operating within EDCA. Half or full duplex is something that mostly applied to p2p serial connections (or p2p wifi), not P2MP. Additionally characteristics like exponential backoff make no sense were wifi any form of duplex, full or half. Certainly much stuff within a txop (block acks for example) can be considered half duplex in a microcosmic context. I wish we actually had words that accurately described wifi's actual behavior. </pedantry> > (for processing ICMP and UDP_RR) is greater than 11e contention window > timings you can get your BE flow responses with extra delay (since > other queues might have responses ready quicker). yes. always having a request pending for each of the 802.11e queues is actually not the best idea, it is better to take advantage of better aggregation afforded by 802.11n/ac, to only have one or two of the queues in use against any given station and promote or demote traffic into a more-right queue. simple example of the damage having all 4 queues always contending is exemplified by running the rrul and rrul_be tests against nearly any given AP. > > I've modified traffic-gen and re-run tests with bursts on all tested > tids/ACs (tid0, tid1, tid5). I'm attaching the results. > > With bursts on all tids you can clearly see BK has much higher latency than BE. The long term goal here, of course, is for BK (or the other queues) to not have seconds of queuing latency but something more bounded to 2x media access time... > (Note, I've changed my AP to QCA988X with oldie firmware 10.1.467 for > this test; it doesn't have the weird hiccups I was seeing on QCA99X0 > and newer QCA988X firmware reports bogus expected throughput which is > most likely a result of my sloppy proof-of-concept change in ath10k). So I should avoid ben greer's firmware for now? > > > Michał > > On 16 March 2016 at 20:48, Jasmine Strong <jas@xxxxxxxx> wrote: >> BK usually has 0 txop, so it doesn't do aggregation. >> >> On Wed, Mar 16, 2016 at 11:55 AM, Bob Copeland <me@xxxxxxxxxxxxxxx> wrote: >>> >>> On Wed, Mar 16, 2016 at 11:36:31AM -0700, Dave Taht wrote: >>> > That is the sanest 802.11e queue behavior I have ever seen! (at both >>> > 6 and 300mbit! in the ath10k patched mac test) >>> >>> Out of curiosity, why does BE have larger latency than BK in that chart? >>> I'd have expected the opposite. >>> >>> -- >>> Bob Copeland %% http://bobcopeland.com/ >>> >>> _______________________________________________ >>> ath10k mailing list >>> ath10k@xxxxxxxxxxxxxxxxxxx >>> http://lists.infradead.org/mailman/listinfo/ath10k >> >> -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
